| 1. |
- Hakonen, Aron, 1970, et al.
(author)
-
Hand-Held Femtogram Detection of Hazardous Picric Acid with Hydrophobic Ag Nanopillar SERS Substrates and Mechanism of Elasto-Capillarity
- 2017
-
In: ACS Sensors. - : American Chemical Society (ACS). - 2379-3694. ; 2:2, s. 198-202
-
Journal article (peer-reviewed)abstract
- Picric acid (PA) is a severe environmental and security risk due to its unstab e, toxic, and explosive properties. It is also challenging to detect in trace amounts and in situ because of its highly acidic and anionic character. Here, we assess sensing of PA under nonlaboratory conditions using surface-enhanced Raman scattering (SERS) silver nanopillar substrates and handheld Raman spectroscopy equipment. The advancing elasto-capillarity effects are explained by molecular dynamics simulations. We obtain a SERS PA detection limit on the order of 20 ppt, corresponding attomole amounts, which together with the simple analysis methodology demonstrates that the presented approach is highly competitive for ultrasensitive analysis in the field.
|
|
| 2. |
- Zucca, M., et al.
(author)
-
Metrology for Inductive Charging of Electric Vehicles (MICEV)
- 2019
-
In: 2019 AEIT International Conference of Electrical and Electronic Technologies for Automotive (AEIT AUTOMOTIVE). ; , s. 1-6
-
Conference paper (peer-reviewed)abstract
- The European Union funded project MICEV aims at improving the traceability of electrical and magnetic measurement at charging stations and to better assess the safety of this technology with respect to human exposure. The paper describes some limits of the instrumentation used for electrical measurements in the charging stations, and briefly presents two new calibration facilities for magnetic field meters and electric power meters. Modeling approaches for the efficiency and human exposure assessment are proposed. In the latter case, electromagnetic computational codes have been combined with dosimetric computational codes making use of highly detailed human anatomical phantoms in order to establish human exposure modeling real charging stations. Detailed results are presented for light vehicles where, according to our calculations, the concern towards human exposure is limited. Currently, the project has reached half way point (about 18 months) and will end in August 2020.
|
|
| 3. |
- Hallstrom, J., et al.
(author)
-
Performance of a modular wideband 1000 kV HVDC reference divider
- 2014
-
In: CPEM Digest (Conference on Precision Electromagnetic Measurements). - 9781479952052 ; , s. 782-783
-
Conference paper (peer-reviewed)abstract
- This paper describes the performance of a wideband HVDC reference divider. The divider concept is a shielded modular divider and it is intended for traceable calibration of HVDC measuring systems up to 1000 kV in customers' laboratories. The first priority in the design was the accuracy of HVDC measurements. In addition, the divider was designed to have wide bandwidth, both to enable measurement of ripple voltages and to prevent damage during possible flashovers. © 2014 IEEE.
|
|
| 4. |
- Holmquist, Lars Erik, et al.
(author)
-
Building Intelligent Environments with Smart-Its
- 2004
-
In: IEEE Computer Graphics and Applications. - 0272-1716 .- 1558-1756. ; 24:1, s. 56-64
-
Journal article (peer-reviewed)abstract
- The development of Smart-Its for building smart environments is discussed. Smart-Its are small, self-contained, stick-on computers that attach to everyday objects. These augmented objects become soft media, enabling dynamic digital relationships with users and each other. A Smart-Its consists of a core board with a wireless transceiver to let the device communicate with other Smart-Its, plus a sensor board that gives the Smart-Its data about its sorroundings. The major advantage of the system is that it allows designers and researchers to construct responsive or intelligent environments.
|
|
| 5. |
- Hällström, Jari K., et al.
(author)
-
Performance of a wideband 200-kV HVDC reference divider module
- 2014
-
In: IEEE Transactions on Instrumentation and Measurement. - 0018-9456 .- 1557-9662. ; 63:9, s. 2264-2270
-
Journal article (peer-reviewed)abstract
- This paper describes the design and performance of a wideband high-voltage dc (HVDC) reference divider module. The module has a nominal voltage of 200 kV, and it has been designed so that a number of modules can be stacked to extend voltages up to 1000 kV. The module, or a stack of modules, will be used for traceable calibration of HVDC measuring systems in customers' laboratories. The first priority in the design was the accuracy of HVDC measurements. In addition, the divider was designed to have wide bandwidth, both to enable measurement of ripple voltages and to prevent damage during possible flashovers.
|
|
| 6. |
- Van Den Berg, F. D., et al.
(author)
-
Product uniformity control - A research collaboration of european steel industries to non-destructive evaluation of microstructure and mechanical properties
- 2018
-
In: Stud. Appl. Electromagn. Mech.. - : IOS Press. - 9781614998358 ; 43, s. 120-129
-
Conference paper (peer-reviewed)abstract
- In steel manufacturing, the conventional method to determine the mechanical properties and microstructure is by offline, destructive (lab-)characterisation of sample material that is typically taken from the head or the tail of the coil. Since coils can be up to 7 km long, the samples are not always representative for the main coil body. Also, the time delay (typically a few days) between the actual production and the availability of the characterisation results implies that these results cannot be exploited for real-time adaptation of the process settings. Information about the microstructure and material properties can also be obtained from electromagnetic (EM) and ultrasonic (US) parameters, which can be measured in real-time, non-destructively, and over the full length of the steel strip product. With the aim to improve the consistency in product quality by use of inline EM and US measurements, a European project called "Product Uniformity Control" (PUC) has been set up as a broad collaboration between 4 major European Steel Manufacturers and 10 Universities / Research institutes. Using both numerical simulations and experimental characterisations, we study the inline measured EM and US parameters in regard of the microstructural and mechanical properties. In this way, we aim to establish an improved understanding of their mutual relationships, and to apply this knowledge in existing and new nondestructive evaluation techniques. In this paper, the concerted approach of modelling and experimental validation will be addressed, and results of this work will be shown in combination with inline measured data.
|
|
| 7. |
- Viallon, J., et al.
(author)
-
A high accuracy reference facility for ongoing comparisons of CO2 in air standards
- 2023
-
In: Metrologia. - : Institute of Physics. - 0026-1394 .- 1681-7575. ; 60:6
-
Journal article (peer-reviewed)abstract
- The design, performance characteristics and validation of a next generation reference facility for carbon dioxide (CO2) in air standards based on manometry is presented. Novel attributes of the facility include automated operation, avoidance of significant pressure corrections for measurements on extracted CO2, fully characterized trapping efficiencies, and reduced measurement uncertainty. Improvements in system performance have been achieved using specific materials, notably Silconert®-treated stainless-steel, providing increased mechanical stability whilst minimizing carbon dioxide adsorption on surfaces, and avoiding use of elastomer O-rings, which would lead to losses of CO2. Full automation of the cryogenic extraction process of CO2 from air has been achieved, avoiding any manual intervention within the temperature stabilized section of the facility, and allowed full characterization and correction for trapping efficiencies and trace water measurement. The facility has been validated across the CO2 in air amount fraction range of (380-800) µmol mol−1 using standards with values traceable to the reference value of the CCQM−K120 (2018) comparison. It was demonstrated to operate with a standard measurement uncertainty of 0.09 µmol mol−1 at 400 µmol mol−1. The automation allows five measurement results per day to be produced with a typical standard deviation of the mean at or below 0.02 µmol mol−1. The facility will be used as a stable reference in the future BIPM.QM−K2 ongoing comparison, to compare consistency of amount fraction values in different CO2 in air standards. The CO2 amount fraction in two ensembles of nine BIPM standards covering the same range will also be measured with the facility to provide their SI-traceable values, and further monitored on a longer time scale. Each ensemble will constitute a CO2 in air scale to be compared with other available scales such as WMO.CO2.X2019 through the BIPM.QM−K5 comparison.
|
|
| 8. |
- Zhao, Yichen, et al.
(author)
-
Relaxation is the key to longer life : suppressed degradation of P3HT films on conductive substrates
- 2014
-
In: Journal of Materials Chemistry A. - : Royal Society of Chemistry (RSC). - 2050-7488 .- 2050-7496. ; 2:33, s. 13270-13276
-
Journal article (peer-reviewed)abstract
- Here we show the dependence of the degree of degradation of poly-3-hexylthiophene (P3HT) films on the conductivity of the supporting substrate. P3HT is widely used for organic solar cells and electronic devices because it allows simple, low cost fabrication and has potential for the fabrication of flexible devices. However, P3HT is known to have a relatively low photostability, and investigating the photodegradation mechanism is an active research field. We find that P3HT films on conductive substrates show significantly retarded degradation and retain their chemical and morphological features when compared to similar films on glass substrates. This 'substrate effect' in retarding the degradation of P3HT films is evident even upon prolonged exposure to air for up to five months.
|
|
