| 1. |
- Bentham, James, et al.
(author)
-
A century of trends in adult human height
- 2016
-
In: eLIFE. - : eLife Sciences Publications Ltd. - 2050-084X. ; 5
-
Journal article (peer-reviewed)abstract
- Being taller is associated with enhanced longevity, and higher education and earnings. We reanalysed 1472 population-based studies, with measurement of height on more than 18.6 million participants to estimate mean height for people born between 1896 and 1996 in 200 countries. The largest gain in adult height over the past century has occurred in South Korean women and Iranian men, who became 20.2 cm (95% credible interval 17.5–22.7) and 16.5 cm (13.3– 19.7) taller, respectively. In contrast, there was little change in adult height in some sub-Saharan African countries and in South Asia over the century of analysis. The tallest people over these 100 years are men born in the Netherlands in the last quarter of 20th century, whose average heights surpassed 182.5 cm, and the shortest were women born in Guatemala in 1896 (140.3 cm; 135.8– 144.8). The height differential between the tallest and shortest populations was 19-20 cm a century ago, and has remained the same for women and increased for men a century later despite substantial changes in the ranking of countries.
|
|
| 2. |
|
|
| 3. |
- Hopfner, M., et al.
(author)
-
Validation of MIPAS ClONO2 measurements
- 2007
-
In: Atmospheric Chemistry and Physics. - : Copernicus GmbH. - 1680-7316 .- 1680-7324. ; 7, s. 257-281
-
Journal article (peer-reviewed)abstract
- Altitude profiles of ClONO2 retrieved with the IMK (Institut fur Meteorologie und Klimaforschung) science-oriented data processor from MIPAS/Envisat (Michelson Interferometer for Passive Atmospheric Sounding on Envisat) mid-infrared limb emission measurements between July 2002 and March 2004 have been validated by comparison with balloon-borne (Mark IV, FIRS2, MIPAS-B), airborne (MIPAS-STR), ground-based (Spitsbergen, Thule, Kiruna, Harestua, Jungfraujoch, Izana, Wollongong, Lauder), and spaceborne (ACE-FTS) observations. With few exceptions we found very good agreement between these instruments and MIPAS with no evidence for any bias in most cases and altitude regions. For balloon-borne measurements typical absolute mean differences are below 0.05 ppbv over the whole altitude range from 10 to 39 km. In case of ACE-FTS observations mean differences are below 0.03 ppbv for observations below 26 km. Above this altitude the comparison with ACE-FTS is affected by the photochemically induced diurnal variation of ClONO2. Correction for this by use of a chemical transport model led to an overcompensation of the photochemical effect by up to 0.1 ppbv at altitudes of 30-35 km in case of MIPAS-ACE-FTS comparisons while for the balloon-borne observations no such inconsistency has been detected. The comparison of MIPAS derived total column amounts with ground-based observations revealed no significant bias in the MIPAS data. Mean differences between MIPAS and FTIR column abundances are 0.11 +/- 0.12 x 10(14) cm(-2) (1.0 +/- 1.1%) and -0.09 +/- 0.19 x 10(14) cm(-2) (-0.8 +/- 1.7%), depending on the coincidence criterion applied. chi(2) tests have been performed to assess the combined precision estimates of MIPAS and the related instruments. When no exact coincidences were available as in case of MIPAS-FTIR or MIPAS-ACE-FTS comparisons it has been necessary to take into consideration a coincidence error term to account for chi(2) deviations. From the resulting chi(2) profiles there is no evidence for a systematic over/underestimation of the MIPAS random error analysis.
|
|
| 4. |
- Wang, D.Y., et al.
(author)
-
Validation of nitric acid retrieved by the IMK-IAA processor from MIPAS/ENVISAT measurements
- 2007
-
In: Atmospheric Chemistry and Physics. - : Copernicus GmbH. - 1680-7316 .- 1680-7324. ; 7, s. 721-738
-
Journal article (peer-reviewed)abstract
- The Michelson Interferometer for Passive Atmospheric Sounding (MIPAS) onboard the ENVISAT satellite provides profiles of temperature and various trace-gases from limb-viewing mid-infrared emission measurements. The stratospheric nitric acid (HNO(3)) from September 2002 to March 2004 was retrieved from the MIPAS observations using the science-oriented data processor developed at the Institut fur Meteorologie und Klimaforschung (IMK), which is complemented by the component of non-local thermodynamic equilibrium (non-LTE) treatment from the Instituto de Astrofisica de Andalucia (IAA). The IMK-IAA research product, different from the ESA operational product, is validated in this paper by comparison with a number of reference data sets. Individual HNO3 profiles of the IMK-IAA MIPAS show good agreement with those of the balloon-borne version of MIPAS (MIPAS-B) and the infrared spectrometer MkIV, with small differences of less than 0.5 ppbv throughout the entire altitude range up to about 38 km, and below 0.2 ppbv above 30 km. However, the degree of consistency is largely affected by their temporal and spatial coincidence, and differences of 1 to 2 ppbv may be observed between 22 and 26 km at high latitudes near the vortex boundary, due to large horizontal inhomogeneity of HNO(3). Statistical comparisons of MIPAS IMK-IAA HNO(3) VMRs with respect to those of satellite measurements of Odin/SMR, ILAS-II, ACE-FTS, as well as the MIPAS ESA product show good consistency. The mean differences are generally +/- 0.5 ppbv and standard deviations of the differences are of 0.5 to 1.5 ppbv. The maximum differences are 2.0 ppbv around 20 to 25 km. This gives confidence in the general reliability of MIPAS HNO(3) VMR data and the other three satellite data sets.
|
|
| 5. |
- Pöntinen, M., et al.
(author)
-
Euclid: Identification of asteroid streaks in simulated images using deep learning
- 2023
-
In: Astronomy and Astrophysics. - : EDP Sciences. - 0004-6361 .- 1432-0746. ; 679
-
Journal article (peer-reviewed)abstract
- The material composition of asteroids is an essential piece of knowledge in the quest to understand the formation and evolution of the Solar System. Visual to near-infrared spectra or multiband photometry is required to constrain the material composition of asteroids, but we currently have such data, especially in the near-infrared wavelengths, for only a limited number of asteroids. This is a significant limitation considering the complex orbital structures of the asteroid populations. Up to 150 000 asteroids will be visible in the images of the upcoming ESA Euclid space telescope, and the instruments of Euclid will offer multiband visual to near-infrared photometry and slitless near-infrared spectra of these objects. Most of the asteroids will appear as streaks in the images. Due to the large number of images and asteroids, automated detection methods are needed. A non-machine-learning approach based on the Streak Det software was previously tested, but the results were not optimal for short and/or faint streaks. We set out to improve the capability to detect asteroid streaks in Euclid images by using deep learning. We built, trained, and tested a three-step machine-learning pipeline with simulated Euclid images. First, a convolutional neural network (CNN) detected streaks and their coordinates in full images, aiming to maximize the completeness (recall) of detections. Then, a recurrent neural network (RNN) merged snippets of long streaks detected in several parts by the CNN. Lastly, gradient-boosted trees (XGBoost) linked detected streaks between different Euclid exposures to reduce the number of false positives and improve the purity (precision) of the sample. The deep-learning pipeline surpasses the completeness and reaches a similar level of purity of a non-machine-learning pipeline based on the StreakDet software. Additionally, the deep-learning pipeline can detect asteroids 0.25–0.5 magnitudes fainter than StreakDet. The deep-learning pipeline could result in a 50% increase in the number of detected asteroids compared to the StreakDet software. There is still scope for further refinement, particularly in improving the accuracy of streak coordinates and enhancing the completeness of the final stage of the pipeline, which involves linking detections across multiple exposures.
|
|
| 6. |
- Brasseur, Z., et al.
(author)
-
Measurement report: Introduction to the HyICE-2018 campaign for measurements of ice-nucleating particles and instrument inter-comparison in the Hyytiala boreal forest
- 2022
-
In: Atmospheric Chemistry and Physics. - : Copernicus GmbH. - 1680-7316 .- 1680-7324. ; 22:8, s. 5117-5145
-
Journal article (peer-reviewed)abstract
- The formation of ice particles in Earth's atmosphere strongly influences the dynamics and optical properties of clouds and their impacts on the climate system. Ice formation in clouds is often triggered heterogeneously by ice-nucleating particles (INPs) that represent a very low number of particles in the atmosphere. To date, many sources of INPs, such as mineral and soil dust, have been investigated and identified in the low and mid latitudes. Although less is known about the sources of ice nucleation at high latitudes, efforts have been made to identify the sources of INPs in the Arctic and boreal environments. In this study, we investigate the INP emission potential from high-latitude boreal forests in the mixed-phase cloud regime. We introduce the HyICE-2018 measurement campaign conducted in the boreal forest of Hyytiala, Finland, between February and June 2018. The campaign utilized the infrastructure of the Station for Measuring Ecosystem-Atmosphere Relations (SMEAR) II, with additional INP instruments, including the Portable Ice Nucleation Chamber I and II (PINC and PINCii), the SPectrometer for Ice Nuclei (SPIN), the Portable Ice Nucleation Experiment (PINE), the Ice Nucleation SpEctrometer of the Karlsruhe Institute of Technology (INSEKT) and the Microlitre Nucleation by Immersed Particle Instrument (mu L-NIPI), used to quantify the INP concentrations and sources in the boreal environment. In this contribution, we describe the measurement infrastructure and operating procedures during HyICE-2018, and we report results from specific time periods where INP instruments were run in parallel for inter-comparison purposes. Our results show that the suite of instruments deployed during HyICE-2018 reports consistent results and therefore lays the foundation for forthcoming results to be considered holistically. In addition, we compare measured INP concentrations to INP parameterizations, and we observe good agreement with the Tobo et al. (2013) parameterization developed from measurements conducted in a ponderosa pine forest ecosystem in Colorado, USA.
|
|
| 7. |
|
|
| 8. |
- Schneider, J., et al.
(author)
-
Additive manufacturing of a metallic optical bench—process development, material qualification and demonstration
- 2023
-
In: CEAS Space Journal. - : Springer Nature. - 1868-2502 .- 1868-2510. ; 15:1, s. 55-68
-
Journal article (peer-reviewed)abstract
- With the large-class science mission ATHENA, the European Space Agency (ESA) aims at exploring the hot and energetic universe with advanced X-Ray technology. As a central component of the telescope, hundreds of silicon pore optic (SPO) modules will be assembled in an optical bench with a diameter of about 2.5 m. Several approaches are under investigation for the manufacturing of this supporting structure, and for handling the challenging constraints with respect to size, geometry and material. In cooperation with ESA, the Fraunhofer IWS is currently investigating the manufacturing of the optical bench made from Ti-6Al-4 V by means of Additive Manufacturing using Laser Metal Deposition (LMD) followed by subtractive finishing. Several development steps have been covered in a holistic manner starting with the system engineering of the production site. The main focus of the activity was on the process development for the Additive Manufacturing as well as the subtractive finishing. Furthermore, the properties of the produced material were also investigated. Within the scope of this publication, a general overview is given about the project related developments, achievements, and flanking activities for solving various challenges. The suitability of the developed technologies and workflows are now being evaluated through the manufacture of a representative, large-scale breadboard.
|
|
| 9. |
- Seidel, A., et al.
(author)
-
Surface modification of additively manufactured gamma titanium aluminide hardware
- 2019
-
In: Journal of laser applications. - : Laser Institute of America. - 1042-346X .- 1938-1387. ; 31:2
-
Journal article (peer-reviewed)abstract
- A major part of additive manufacturing focuses on the fabrication of metallic parts in different fields of applications. Examples include components for jet engines and turbines and also implants in the medical sector. Titanium alloys represent a material group which is used cross-sectoral in a large number of applications. The present paper addresses the titanium aluminides in particular. These materials have a low density in combination with a comparatively high-temperature resistance [G. Sauthoff, Intermetallics (Wiley-VCH Verlag, Weinheim, Germany, 2008)]. Nevertheless, the laser material processing is rather challenging because of their distinct tendency to lamellar interface cracking. This requires tailored processing strategies and equipment [C. Leyens et al., in Ti-2015: The 13th World Conference on Titanium, Symposium 5. Intermetallics and MMCs, 16–20 August 2015, San Diego, CA (The Minerals, Metals & Materials Society, Pittsburgh, PA, 2016)]. This work focusses on tailored processing of titanium aluminides with focus on the process-dependent surface characteristics. This includes the as-built status for powder bed processing and direct laser metal deposition but also the surface modification via post and/or advanced machining. Finally, comprehensive characterization is performed using destructive as well as nondestructive testing methods. The latter includes 3D scanning, computed tomography, microscopic analysis, and, in particular, surface roughness measurements.
|
|
