| 1. |
- Sun, S., et al.
(författare)
-
Thermal performance characterization of nano thermal interface materials after power cycling
- 2012
-
Ingår i: Proceedings - Electronic Components and Technology Conference. - 0569-5503. - 9781467319669 ; , s. 1426-1430
-
Konferensbidrag (refereegranskat)abstract
- The need for faster, smaller, and more reliable and efficient products has resulted in increase of heat generated in microelectronic components. The removal of the heat generated is an important issue in electronic packaging. A novel Nano-TIM was developed to improve the heat dissipation of electronics packaging. This paper aims at studying the heat dissipation performance of a new class of nano-structured polymer-metal composite film (Nano-TIM) after power cycling. The new Nano-TIM uses metal to provide continuous thermal pathways while using nano-polymer to control the elasticity of the TIM. Through semiconductor processing and RTD principle, chips including 5*5, 10*10, 20*20, 30*30 (mm 2), were developed to study different size's influence on heat dissipation effect of the Nano-TIM. Additional parameters studied include power effect. RTD is used respectively to measure the junction temperature, and then the R thJC (Junction-to-Case Thermal Resistance) is calculated afterwards. The Transient thermal resistances of the Nano-TIM were also tested by T3Ster method to further study heat dissipation effect of Nano-TIM. The morphologies and interaction between the Nano-TIM and chips were carefully studied using X-ray Scanning Microscope to analyze heat flow path. The result shows that Nano-TIMs can be used to 30 mm in chip length as the thermal interface material.
|
|
| 2. |
- Zhang, L., et al.
(författare)
-
Study on the adhesion strength of new nano-structured polymer-metal composite for thermal interface material (Nano-TIM) under different pressures
- 2011
-
Ingår i: Proceedings - 12th International Conference on Electronic Packaging Technology and High Density Packaging, ICEPT-HDP 2011, Shanghai, 8-11 August 2011. - 9781457717680 ; , s. 426-429
-
Konferensbidrag (refereegranskat)abstract
- With the continual increase in cooling demand for microprocessors, the microelectronics industry has been increasingly focused on the development of thermal solutions. Thermal Interface Material (TIM) plays a key role in reducing the thermal resistance of packaging and the thermal resistance between the electronic device and the external cooling components. Nano-TIM, a new type of thermal interface material, was developed to improve the heat dissipation of electronic devices. This paper describes work undertaken to research the reliability of Nano-TIM. Pull tests were used to investigate the shear strength of samples with Nano-TIM of different thicknesses coalesced between two PCBs with Sn coating made under different pressure. Scanning Electron Microscopy (SEM) analysis techniques were used to determine the morphology of the shear fracture section after pull tests and observe the structure of the cross section of Nano-TIM coalesced between two PCBs with Sn coating.
|
|
| 3. |
- Liu, Z. Y., et al.
(författare)
-
Micromechanical characterization of casting-induced inhomogeneity in an Al0.8CoCrCuFeNi high-entropy alloy
- 2011
-
Ingår i: Scripta Materialia. - : Elsevier BV. - 1359-6462. ; 64:9, s. 868-871
-
Tidskriftsartikel (refereegranskat)abstract
- The microstructural features and micromechanical behavior of individual phases in a cast Al0.8CoCrCuFeNi high-entropy alloy (HEA) were characterized by high-resolution scanning electron microscopy and micro-compression tests. Use of neutron diffraction enabled the detection of a new phase which was otherwise unobservable by conventional X-ray diffraction. The identified phase constitution agreed well with the compositional analysis and the micro-compression results. The delicate microscale characterization of individual phase provides new insights for the design of novel HEAs with desirable mechanical properties. (C) 2011 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
|
|
| 4. |
- Tang, X., et al.
(författare)
-
Development and characterisation of nanofiber films with high adhesion
- 2011
-
Ingår i: Proceedings - Electronic Components and Technology Conference. - 0569-5503. ; , s. 673-677
-
Konferensbidrag (refereegranskat)abstract
- With the development of thermal management, thermal interface material (TIM) plays a more and more important role in electronic packaging. This paper reports the study on fabrication of a nanofiber films used for nano-thermal interface material (nano-TIM) with the adhesive function. The nano-TIM with high thermal conductivity and low thermal resistivity has been fabricated by electrospinning process. In the present work, hotmelt was added into the electrospinning solution to improve the adhesion properties of the film. The morphology of the film was observed by Scanning Electrical Microscope (SEM). The nanofiber films have a nano-scale structure with hotmelt randomly attached into the fiber matrix. Shear tests were conducted to measure the bonding strength of nanofiber films. The results show that the nanofiber films reached a 6.52 MPa in terms of average shear strength, more than 2 times better than the case without the hotmelt addition. © 2011 IEEE.
|
|
| 5. |
- Carlberg, Björn, 1983, et al.
(författare)
-
Polymer nanofiber based continuous metal phase composite for thermal management applications
- 2010
-
Ingår i: 3rd Electronics System Integration Technology Conference, ESTC 2010; Berlin; Germany; 13 September 2010 through 16 September 2010. - 9781424485536 ; , s. Art. no. 5642950-
-
Konferensbidrag (refereegranskat)abstract
- A new composite design approach for thermal interface materials is presented. A porous electro spun nanofiber network composed of temperature stable poly imide was infiltrated with liquid phase indium at a pressure of 30 MPa. The polymer phase defmes composition and geometry, while the continuous metal phase gives binding to surfaces and high thermal conductivity. The composite was characterized by assembly of tri-layer copper/TIM/copper sandwich structures and subsequent xenon flash measurements extracting the thermal properties of the intermediate TIM layer. The interfacial contact resistance was found to be 8 Kmm2/W and the thermal conductivity was 28 W/mK, indicating the potential for use in thermal management applications.
|
|
| 6. |
- Zhang, Y., et al.
(författare)
-
Characterization of nano-enhanced interconnect materials for fine pitch assembly
- 2014
-
Ingår i: Soldering and Surface Mount Technology. - : Emerald. - 1758-6836 .- 0954-0911. ; 26:1, s. 12-17
-
Tidskriftsartikel (refereegranskat)abstract
- Purpose - Multiple fillers are adopted to study the filler influences on electrical and mechanical properties of the conductive adhesives. The performances of the developed nano-enhanced interconnect materials in printing process are also evaluated. The paper aims to discuss these issues. Design/methodology/approach - Micron-sized silver flakes are used as the basic fillers, and submicro- and nano-sized silver spheres and carbon nanotubes (CNTs) are adopted to obtain conductive adhesives with multiple fillers. Differential scanning calorimetry measurement is carried out to characterize the curing behavior of the samples with different fillers, four-probe method is used to obtain the bulk resistivity, shear test is conducted for adhesive strength, and environmental loading test is also involved. Furthermore, printing trials with different patterns have been carried out. Findings -The electrical resistivity of the adhesives with submicro-sized silver spheres does not monotonically change with the increasing sphere proportion, and there exists an optimized value for the ratio of silver flakes to spheres. Samples with relatively small amount of CNT additives show improved electrical properties, while their mechanical strengths tend to decrease. For the printing application, the adhesives with 18.3 volume% filler content behave much better than those with lower filler content of 6 percent. The presence of the nano-particles makes a slight improvement in the printing results. Research limitations/implications - More detailed printing performance and reliability test of the samples need to be carried out in the future. Originality/value - The conductive adhesives as interconnect materials exhibit some improved properties with optimized bimodal or trimodal fillers. The additive of the nano-fillers affects slightly on the printing quality of the bimodal conductive adhesives.
|
|
| 7. |
- Carlberg, Björn, 1983, et al.
(författare)
-
Polymer-metal nanofibrous composite for thermal management of microsystems
- 2012
-
Ingår i: Materials Letters. - : Elsevier BV. - 1873-4979 .- 0167-577X. ; 75, s. 229-232
-
Tidskriftsartikel (refereegranskat)abstract
- In this letter, a composite structure based on a porous electrospun polyimide structure infiltrated with indium aimed at thermal interface material applications is presented. A porous nanofibrous structure was prepared by electrospinning of polyimide. An interfacial nanocomposite layer of silver nanoparticles partially or fully embedded in the polyimide matrix was synthesized on the fiber surfaces, followed by autocatalytic deposition of a uniform silver coating (using the interfacial layer as an anchored seed layer) serving as a reactive wetting layer for the infiltrating melt. The thermal performance of the composite was evaluated and the thermal conductivity was determined to be 27 W/mK, accompanied by low contact resistance of the metallurgical bond (
|
|
| 8. |
- Carlberg, Björn, 1983, et al.
(författare)
-
Surface-Confined Synthesis of Silver Nanoparticle Composite Coating on Electrospun Polyimide Nanofibers
- 2011
-
Ingår i: Small. - : Wiley. - 1613-6810 .- 1613-6829. ; 7:21, s. 3057-3066
-
Tidskriftsartikel (refereegranskat)abstract
- A methodology for fabricating hierarchical nanostructures by surface-confined synthesis of silver nanoparticles on electrospun polyimide nanofibers is reported. Through surface-confined imide cleavage at the dianhydride domain via immersion in an aqueous KOH solution, potassium polyamate coatings of accurately defined thickness are formed (at a rate of 25 nm h(-1)). By utilizing the ion-exchange capability of the polyamate resin, silver ions are introduced through immersion in an aqueous AgNO(3) solution. Subsequent reduction of the metal ion species leads to the formation of nanoparticles at the fiber surface. Two modes of reduction, chemical and thermal, are investigated in the report, each leading to distinct morphologies of the nanoparticle coatings. Via thermal reduction, a composite surface layer consisting of monodisperse silver nanoparticles (average diameter 5.2 nm) embedded in a re-imidized polyimide matrix is achieved. In the case of chemical reduction, the reduction process occurs preferentially at the surface of the fiber, leading to the formation of silver nanoparticles anchored at the surface, though not embedded, in a polyamic acid matrix. By regulating the modification depth, control of the particle density on the fiber surface is established. In both reduction approaches, the polyimide nanofiber core exhibits maintained integrity.
|
|
| 9. |
- Casa, Marcello, et al.
(författare)
-
Development and characterization of graphene-enhanced thermal conductive adhesives
- 2014
-
Ingår i: 15th International Conference on Electronic Packaging Technology, ICEPT 2014; Wangjiang HotelChengdu; China; 12 August 2014 through 15 August 2014. - 9781479947072 ; :Art. no. 6922700, s. 480-483
-
Konferensbidrag (refereegranskat)abstract
- According to Moore's Laws, complexity and power densities of electronic devices are increased during the last decades, moreover their dimensions are shrinking to nanometers causing hot-spot temperature escalation. Thermal management, therefore, becomes a critical issue for next generation of electronics. This scenario motivates development of novel thermal conductive adhesive (TCA) with enhanced thermal conductivity. Conventional TCAs use polymers as the matrix (base material) and utilize large loading weight fraction of the filler, usually silver particles, to achieve the thermal conductivity of 1-4 W/ m K at room temperature [1]. Lately it was discovered that graphene exhibit superior thermal conductivity [2] even when they are incorporated with matrix materials [3], which offers a potential to develop high thermal conductive graphene-filled compound. In this paper, a new functionalized graphene and its filled TCA have been developed and characterized. Starting from pristine graphite flakes, graphene was prepared through chemical exfoliation and functionalized with a nano silver layer to form a special metal/graphene hybrid material. Moreover, an efficient method to uniformly disperse the nano-scaled graphene hybrid material in silver-epoxy matrix was developed. Cross-section view of SEM has shown a homogeneous component structure, and TGA analysis of hybrid material is given. The developed compound is based on a commercial TCA which is composed with epoxy matrix and micro-sized Ag flakes. Thermal characterization through Laser-flash equipment has indicated that a significant thermal conductivity improvement was achieved through adding functionalized graphene into the material. Different TCA samples with different weight percentages of functionalized graphene ranging from 0 % (reference) to 11.5 % were prepared and tested to study thermal conductivity change. Data show that a thermal conductivity value of 7.6 W/ m K is reached when the graphene/silver percentage is 11.5 % that is almost 4 times higher than our reference.
|
|
| 10. |
- Chen, S., et al.
(författare)
-
A solder joint structure with vertically aligned carbon nanofibres as reinforcements
- 2014
-
Ingår i: Proceedings of the 5th Electronics System-Integration Technology Conference, ESTC 2014. - 9781479940264 ; , s. Art. no. 6962851-
-
Konferensbidrag (refereegranskat)abstract
- In this paper, a solder joint structure was developed for the electronic packaging industry. Vertically aligned carbon nanofibres (VACNFs) were grown, transferred and used at the interface between Si/Au pads and Sn-3.0Ag-0.5Cu (SAC305) alloy as reinforcements in order to increase the solder joint thermal fatigue resistance. The transfer and assembly processes related to VACNFs were optimised and developed. The thermal cycling test results show that the thermal fatigue life of VACNF/SAC305 solder joints is 40% longer than that of pure SAC305. The dye and pry analysis and scanning electron microscopy observation prove that the VACNFs can effectively delay the crack propagation near the interface and consequently prolong the solder joint thermal fatigue life.
|
|
