| 1. |
- Abdesselam, A., et al.
(författare)
-
Engineering for the ATLAS SemiConductor Tracker (SCT) end-cap
- 2008
-
Ingår i: Journal of Instrumentation. - 1748-0221 .- 1748-0221. ; 3
-
Tidskriftsartikel (refereegranskat)abstract
- The ATLAS SemiConductor Tracker (SCT) is a silicon-strip tracking detector which forms part of the ATLAS inner detector. The SCT is designed to track charged particles produced in proton-proton collisions at the Large Hadron Collider (LHC) at CERN at an energy of 14 TeV. The tracker is made up of a central barrel and two identical end-caps. The barrel contains 2112 silicon modules, while each end-cap contains 988 modules. The overall tracking performance depends not only on the intrinsic measurement precision of the modules but also on the characteristics of the whole assembly, in particular, the stability and the total material budget. This paper describes the engineering design and construction of the SCT end-caps, which are required to support mechanically the silicon modules, supply services to them and provide a suitable environment within the inner detector. Critical engineering choices are highlighted and innovative solutions are presented - these will be of interest to other builders of large-scale tracking detectors. The SCT end-caps will be fully connected at the start of 2008. Further commissioning will continue, to be ready for proton-proton collision data in 2008.
|
|
| 2. |
- Abdesselam, A., et al.
(författare)
-
The barrel modules of the ATLAS semiconductor tracker
- 2006
-
Ingår i: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576. ; 568:2, s. 642-671
-
Tidskriftsartikel (refereegranskat)abstract
- This paper describes the silicon microstrip modules in the barrel section of the SemiConductor Tracker (SCT) of the ATLAS experiment at the CERN Large Hadron Collider (LHC). The module requirements, components and assembly techniques are given, as well as first results of the module performance on the fully assembled barrels that make up the detector being installed in the ATLAS experiment.
|
|
| 3. |
- Abdesselam, A., et al.
(författare)
-
The ATLAS semiconductor tracker end-cap module
- 2007
-
Ingår i: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576. ; 575:3, s. 353-389
-
Tidskriftsartikel (refereegranskat)abstract
- The challenges for the tracking detector systems at the LHC are unprecedented in terms of the number of channels, the required read-out speed and the expected radiation levels. The ATLAS Semiconductor Tracker. (SCT) end-caps have a total of about 3 million electronics channels each reading out every 25 ns into its own on-chip 3.3 mu s buffer. The highest anticipated dose after 10 years operation is 1.4x10(14) cm(-2) in units of 1 MeV neutron equivalent (assuming the damage factors scale with the non-ionising energy loss). The forward tracker has 1976 double-sided modules, mostly of area similar to 70 cm(2), each having 2 x 768 strips read out by six ASICs per side. The requirement to achieve an average perpendicular radiation length of 1.5% X-0, while coping with up to 7 W dissipation per module (after irradiation), leads to stringent constraints on the thermal design. The additional requirement of 1500e(-) equivalent noise charge (ENC) rising to only 1800e(-) ENC after irradiation, provides stringent design constraints on both the high-density Cu/Polyimide flex read-out circuit and the ABCD3TA read-out ASICs. Finally, the accuracy of module assembly must not compromise the 16 mu m (r phi) resolution perpendicular to the strip directions or 580 mu m radial resolution coming from the 40 mrad front-back stereo angle. A total of 2210 modules were built to the tight tolerances and specifications required for the SCT. This was 234 more than the 1976 required and represents a yield of 93%. The component flow was at times tight, but the module production rate of 40-50 per week was maintained despite this. The distributed production was not found to be a major logistical problem and it allowed additional flexibility to take advantage of where the effort was available, including any spare capacity, for building the end-cap modules. The collaboration that produced the ATLAS SCT end-cap modules kept in close contact at all times so that the effects of shortages or stoppages at different sites could be rapidly resolved.
|
|
| 4. |
- Ghavami, Saeid, et al.
(författare)
-
Brevinin-2R semi-selectively kills cancer cells by a distinct mechanism, which involves the lysosomal-mitochondrial death pathway
- 2008
-
Ingår i: Journal of Cellular and Molecular Medicine (Print). - : Wiley-Blackwell. - 1582-1838 .- 1582-4934. ; 12:3, s. 1005-1022
-
Tidskriftsartikel (refereegranskat)abstract
- Brevinin-2R is a novel non-hemolytic defensin that was isolated from the skin of the frog Rana ridibunda. It exhibits preferential cytotoxicity towards malignant cells, including Jurkat (T-cell leukemia), BJAB (B-cell lymphoma), HT29/219, SW742 (colon carcinomas), L929 (fibrosarcoma), MCF-7 (breast adenocarcinoma), A549 (lung carcinoma), as compared to primary cells including peripheral blood mononuclear cells (PBMC), T cells and human lung fibroblasts. Jurkat and MCF-7 cells overexpressing Bcl2, and L929 and MCF-7 over-expressing a dominant-negative mutant of a pro-apoptotic BNIP3 (ΔTM-BNIP3) were largely resistant towards Brevinin-2R treatment. The decrease in mitochondrial membrane potential (ΔΨm), or total cellular ATP levels, and increased reactive oxygen species (ROS) production, but not caspase activation or the release of apoptosis-inducing factor (AIF) or endonuclease G (Endo G), were early indicators of Brevinin-2R-triggered death. Brevinin-2R interacts with both early and late endosomes. Lysosomal membrane permeabilization inhibitors and inhibitors of cathepsin-B and cathepsin-L prevented Brevinin-2R-induced cell death. Autophagosomes have been detected upon Brevinin-2R treatment. Our results show that Brevinin-2R activates the lysosomalmitochondrial death pathway, and involves autophagy-like cell death.
|
|
| 5. |
- Klionsky, Daniel J., et al.
(författare)
-
Guidelines for the use and interpretation of assays for monitoring autophagy in higher eukaryotes
- 2008
-
Ingår i: Autophagy. - : Landes Bioscience. - 1554-8627 .- 1554-8635. ; 4:2, s. 151-175
-
Forskningsöversikt (refereegranskat)abstract
- Research in autophagy continues to accelerate,1 and as a result many new scientists are entering the field. Accordingly, it is important to establish a standard set of criteria for monitoring macroautophagy in different organisms. Recent reviews have described the range of assays that have been used for this purpose.2,3 There are many useful and convenient methods that can be used to monitor macroautophagy in yeast, but relatively few in other model systems, and there is much confusion regarding acceptable methods to measure macroautophagy in higher eukaryotes. A key point that needs to be emphasized is that there is a difference between measurements that monitor the numbers of autophagosomes versus those that measure flux through the autophagy pathway; thus, a block in macroautophagy that results in autophagosome accumulation needs to be differentiated from fully functional autophagy that includes delivery to, and degradation within, lysosomes (in most higher eukaryotes) or the vacuole (in plants and fungi). Here, we present a set of guidelines for the selection and interpretation of the methods that can be used by investigators who are attempting to examine macroautophagy and related processes, as well as by reviewers who need to provide realistic and reasonable critiques of papers that investigate these processes. This set of guidelines is not meant to be a formulaic set of rules, because the appropriate assays depend in part on the question being asked and the system being used. In addition, we emphasize that no individual assay is guaranteed to be the most appropriate one in every situation, and we strongly recommend the use of multiple assays to verify an autophagic response.
|
|
| 6. |
- Maddika, Subbareddy, et al.
(författare)
-
Cancer-specific toxicity of apoptin is independent of death receptors but involves the loss of mitochondrial membrane potential and the release of mitochondrial cell-death mediators by a Nur77-dependent pathway
- 2005
-
Ingår i: Journal of Cell Science. - : The Company of Biologists Ltd.. - 0021-9533 .- 1477-9137. ; 118, s. 4485-4493
-
Tidskriftsartikel (refereegranskat)abstract
- Apoptin, a small proline-rich protein derived from the chicken anaemia virus, induces cell death selectively in cancer cells. The signalling pathways of apoptin-induced, cancer cell-selective apoptosis are not well understood. Here, we demonstrate that apoptin triggers apoptosis by activating the mitochondrial/intrinsic pathway, and that it acts independently of the death receptor/extrinsic pathway. Jurkat cells deficient in either FADD or caspase-8 (which are both necessary for the extrinsic pathway) were equally as sensitive to apoptin as their parental clones. This demonstrates that apoptin is likely to act through the mitochondrial death pathway. Apoptin treatment causes a loss of mitochondrial membrane potential, and release of the mitochondrial proteins cytochrome c and apoptosis-inducing factor. Apoptin-induced cell death is counteracted by the anti-apoptotic Bcl-2 family members, Bcl-2 itself and Bcl-XL, as shown in Jurkat leukaemia cells. In addition, we describe the processing and activation of caspase-3. By contrast, cleavage of caspase-8, which is predominantly triggered by the death receptor pathway, is not observed. Furthermore, apoptin triggers the cytoplasmic translocation of Nur77, and the inhibition of Nur77 expression by siRNA significantly protects MCF7 cells from apoptin-triggered cell death. Thus, our data indicate that the apoptin death signal(s) ultimately converges at the mitochondria, and that it acts independently of the death receptor pathway.
|
|
