| 1. |
- Yang, Lei, et al.
(författare)
-
Experimental and Theoretical Investigation of the Function of 4- tert -Butyl Pyridine for Interface Energy Level Adjustment in Efficient Solid-State Dye-Sensitized Solar Cells
- 2018
-
Ingår i: ACS Applied Materials and Interfaces. - : American Chemical Society. - 1944-8244 .- 1944-8252. ; 10:14, s. 11572-11579
-
Tidskriftsartikel (refereegranskat)abstract
- 4-tert-Butylpyridine (t-BP) is commonly used in solid state dye-sensitized solar cells (ssDSSCs) to increase the photovoltaic performance. In this report, the mechanism how t-BP functions as a favorable additive is investigated comprehensively. ssDSSCs were prepared with different concentrations of t-BP, and a clear increase in efficiency was observed up to a maximum concentration and for higher concentrations the efficiency thereafter decreases. The energy level alignment in the complete devices was measured using hard X-ray photoelectron spectroscopy (HAXPES). The results show that the energy levels of titanium dioxide are shifted further away from the energy levels of spiro-OMeTAD as the t-BP concentration is increased. This explains the higher photovoltage obtained in the devices with higher t-BP concentration. In addition, the electron lifetime was measured for the devices and the electron lifetime was increased when adding t-BP, which can be explained by the recombination blocking effect at the surface of TiO2. The results from the HAXPES measurements agree with those obtained from density functional theory calculations and give an understanding of the mechanism for the improvement, which is an important step for the future development of solar cells including t-BP.
|
|
| 2. |
- Hao, Yan, et al.
(författare)
-
Peripheral Hole Acceptor Moieties on an Organic Dye Improve Dye-Sensitized Solar Cell Performance
- 2015
-
Ingår i: Advanced Science. - : Wiley-Blackwell. - 2198-3844. ; 2:11
-
Tidskriftsartikel (refereegranskat)abstract
- Investigation of charge transfer dynamics in dye-sensitized solar cells is of fundamental interest and the control of these dynamics is a key factor for developing more efficient solar cell devices. One possibility for attenuating losses through recombination between injected electrons and oxidized dye molecules is to move the positive charge further away from the metal oxide surface. For this purpose, a metal-free dye named E6 is developed, in which the chromophore core is tethered to two external triphenylamine (TPA) units. After photoinduced electron injection into TiO2, the remaining hole is rapidly transferred to a peripheral TPA unit. Electron-hole recombination is slowed down by 30% compared to a reference dye without peripheral TPA units. Furthermore, it is found that the added TPA moieties improve the electron blocking effect of the dye, retarding recombination of electrons from TiO2 to the cobalt-based electrolyte.
|
|
| 3. |
- Wu, Hua, et al.
(författare)
-
Mixed-Halide Double Perovskite Cs2AgBiX6 (X=Br, I) with Tunable Optical Properties via Anion Exchange
- 2021
-
Ingår i: ChemSusChem. - : Wiley. - 1864-5631 .- 1864-564X. ; 14:20, s. 4507-4515
-
Tidskriftsartikel (refereegranskat)abstract
- Lead-free double perovskites, A2M+M′3+X6, are considered as promising alternatives to lead-halide perovskites, in optoelectronics applications. Although iodide (I) and bromide (Br) mixing is a versatile tool for bandgap tuning in lead perovskites, similar mixed I/Br double perovskite films have not been reported in double perovskites, which may be due to the large activation energy for ion migration. In this work, mixed Br/I double perovskites were realized utilizing an anion exchange method starting from Cs2AgBiBr6 solid thin-films with large grain-size. The optical and structural properties were studied experimentally and theoretically. Importantly, the halide exchange mechanism was investigated. Hydroiodic acid was the key factor to facilitate the halide exchange reaction, through a dissolution–recrystallization process. In addition, the common organic iodide salts could successfully perform halide-exchange while retaining high mixed-halide phase stability and strong light absorption capability.
|
|
| 4. |
- Lindblad, Rebecka, et al.
(författare)
-
Controlling energy level positions in hole conducting molecular films by additives
- 2018
-
Ingår i: Journal of Electron Spectroscopy and Related Phenomena. - : Elsevier. - 0368-2048 .- 1873-2526. ; 224, s. 100-106
-
Tidskriftsartikel (refereegranskat)abstract
- Hard X-ray photoelectron spectroscopy (HAXPES) has been used to study the bulk electronic structure of thin molecular films of the organic compounds 2,2',7,7'-tetrakis (N,N'-di-p-methoxyphenyl-amine)-9,9'-spiro-bifluorene (spiro-OMeTAD), 4-(diethylamino)-benzaldehyde-1,1-diphenyl-hydrazone (DEH) and poly(3-hexylthiophene) (P3HT). Molecular layers of these compounds are hole conducting, a property that for example has been used in different solar cell configurations. The function of such a device benefits from the inclusion of additives such as Li-TFSI, or dopants such as Co-complexes, into the molecular layer. Here we report on effects of adding Li-TFSI to DEH and P3HT as observed by photoelectron spectroscopy and we compare with results on the spiro-OMeTAD hole conductor. It can be concluded that the Li-salt causes a shift of the Fermi level in DEH and P3HT towards the HOMO resulting in a p-doping of the molecular material. Similar shifts of the Fermi level could also be observed when adding different Co(+III) complexes to the Spiro-OMeTAD hole conductor, indicating means for more controlled doping.
|
|
| 5. |
- Zhang, Jinbao, et al.
(författare)
-
Matrix-Assisted Laser Desorption/Ionization Mass Spectrometric Analysis of Poly(3,4-ethylenedioxythiophene) in Solid-State Dye-Sensitized Solar Cells : Comparison of In Situ Photoelectrochemical Polymerization in Aqueous Micellar and Organic Media
- 2015
-
Ingår i: Analytical Chemistry. - : American Chemical Society (ACS). - 0003-2700 .- 1520-6882. ; 87:7, s. 3942-3948
-
Tidskriftsartikel (refereegranskat)abstract
- Solid-state dye-sensitized solar cells (sDSCs) are devoid of such issues as electrolyte evaporation or leakage and electrode corrosion, which are typical for traditional liquid electrolyte-based DSCs. Poly(3,4-ethylenedioxythiophene) (PEDOT) is one of the most popular and efficient p-type conducting polymers that are used in sDSCs as a solid-state hole-transporting material. The most convenient way to deposit this insoluble polymer into the dye-sensitized mesoporous working electrode is in situ photoelectrochemical polymerization. Apparently, the structure and the physicochemical properties of the generated conducting polymer, which determine the photovoltaic performance of the corresponding solar cell, can be significantly affected by the preparation conditions. Therefore, a simple and fast analytical method that can reveal information on polymer chain length, possible chemical modifications, and impurities is strongly required for the rapid development of efficient solar energy-converting devices. In this contribution, we applied matrix-assisted laser desorption/ionization mass spectrometry (MALDI MS) for the analysis of PEDOT directly on sDSCs. It was found that the PEDOT generated in aqueous micellar medium possesses relatively shorter polymeric chains than the PEDOT deposited from an organic medium. Furthermore, the micellar electrolyte promotes a transformation of one of the thiophene terminal units to thiophenone. The introduction of a carbonyl group into the PEDOT molecule impedes the growth of the polymer chain and reduces the conductivity of the final polymer film. Both the simplicity of sample preparation (only application of the organic matrix onto the solar cell is needed) and the rapidity of analysis hold the promise of making MALDI MS an essential tool for the physicochemical characterization of conducting polymer-based sDSCs.
|
|
| 6. |
- Cappel, Ute B., et al.
(författare)
-
Characterization of the Interface Properties and Processes in Solid State Dye-Sensitized Solar Cells Employing a Perylene Sensitizer
- 2011
-
Ingår i: The Journal of Physical Chemistry C. - : American Chemical Society (ACS). - 1932-7447 .- 1932-7455. ; 115:10, s. 4345-4358
-
Tidskriftsartikel (refereegranskat)abstract
- We recently reported on a perylene sensitizer, ID176, which performs much better in solid state dye-sensitized solar cells than in those using liquid electrolytes with iodide/tri-iodide as the redox couple (J. Phys. Chem. C2009, 113, 14595-14597). Here, we present a characterization of the sensitizer and of the TiO2/dye interface by UV-visible absorption and fluorescence spectroscopy, spectroelectrochemistry, photoelectron spectroscopy, electroabsorption spectroscopy, photoinduced absorption spectroscopy, and femtosecond transient absorption measurements. We report that the absorption spectrum of the sensitizer is red-shifted by addition of lithium ions to the surface due to a downward shift of the excited state level of the sensitizer, which is of the same order of magnitude as the downward shift of the titanium dioxide conduction band edge. Results from photoelectron spectroscopy and electrochemistry suggest that the excited state is largely located below the conduction band edge of TiO2 but that there are states in the band gap of TiO2 which might be available for photoinduced electron injection. The sensitizer was able to efficiently inject into TiO2, when a lithium salt was present on the surface, while injection was much less effective in the absence of lithium ions or in the presence of solvent. In the presence of the hole conductor 2,2-,7,7-tetrakis-(N,N-di-p-methoxyphenyl-amine)-9,9-spirobifluorene (spiro-MeOTAD) and LiTFSI, charge separation was monitored by the emergence of a Stark shift of the dye in transient absorption spectra, and both injection and regeneration appear to be completed within 1 ps. Regeneration by spiro-MeOTAD is therefore several orders of magnitude faster than regeneration by iodide, and ID176 can even be photoreduced by spiro-MeOTAD.
|
|
| 7. |
- Feldt, Sandra M., et al.
(författare)
-
Characterization of surface passivation by poly(methylsiloxane) for dye-sensitized solar cells employing the ferrocene redox couple.
- 2010
-
Ingår i: The Journal of Physical Chemistry C. - : American Chemical Society (ACS). - 1932-7447 .- 1932-7455. ; 114:23, s. 10551-10558
-
Tidskriftsartikel (refereegranskat)abstract
- One-electron outer-sphere redox couples, such as ferrocene/ferrocenium, are an interesting alternative to the iodide/triiodide redox couple that is normally employed in dye-sensitized solar cells (DSCs) because they should reduce the driving force needed to regenerate the dye. Unfortunately, one-electron redox couples also show enhanced recombination with photoinjected electrons, and methods to inhibit this recombination are needed for functioning DSCs. In this study, dye-sensitized titanium dioxide surfaces were passivated by a trichloromethylsilane reaction in order to decrease the fast recombination rates when using the ferrocene redox couple. The formation and binding of poly(methylsiloxane) on the dye-sensitized TiO2 surface was verified with infrared spectroscopy and photoelectron spectroscopy. Photoelectrochemical characterization of the silanization method showed that the treatment decreased the recombination rate of photoinjected electrons with ferrocenium and thereby improved the efficiency of the DSC. Transient absorption spectroscopy revealed, however, that the poly(methylsiloxane) coatings slowed down the regeneration of the oxidized dye by the ferrocene and prevented the regeneration of some of the dye molecules.
|
|
| 8. |
- Hahlin, Maria, et al.
(författare)
-
Electronic and molecular structures of organic dye/TiO2 interfaces for solar cell applications : a core level photoelectron spectroscopy study
- 2010
-
Ingår i: Physical Chemistry, Chemical Physics - PCCP. - : Royal Society of Chemistry (RSC). - 1463-9076 .- 1463-9084. ; 12:7, s. 1507-1517
-
Tidskriftsartikel (refereegranskat)abstract
- The electronic and molecular properties of three organic dye molecules with the general structure donor-linker-anchor have been investigated using core level photoelectron spectroscopy (PES). The molecules contain a diphenylaniline donor unit, a thiophene linker unit, and cyanoacrylic acid or rhodanine-3-acetic acid anchor units. They have been investigated both in the form of a multilayer and adsorbed onto nanoporous TiO2 and the experimental results were also compared with DFT calculations. The changes at the dye-sensitized TiO2 surface due to the modification of either the donor unit or the anchor unit was investigated and the results showed important differences in coverage as well as in electronic and molecular surface properties. By measuring the core level binding energies, the sub-molecular properties were characterized and the result showed that the adsorption to the TiO2 influences the energy levels of the sub-molecular units differently.
|
|
| 9. |
- Hua, Yong, et al.
(författare)
-
Facile synthesis of fluorene-based hole transport materials for highly efficient perovskite solar cells and solid-state dye-sensitized solar cells
- 2016
-
Ingår i: Nano Energy. - : Elsevier. - 2211-2855 .- 2211-3282. ; 26, s. 108-113
-
Tidskriftsartikel (refereegranskat)abstract
- Two novel low-cost fluorene-based hole transport materials (HTMs) HT1 and HT2 as alternatives to the expensive HTM Spiro-OMeTAD have been designed and synthesized for the application in perovskite solar cells (PSCs) and solid-state dye-sensitized solar cell (ssDSCs). The two HTMs were prepared through a facile two-step reaction from cheap starting material and with a total yield higher than 90%. These HTMs exhibit good solubility and charge-transport ability. PSCs based on HT2 achieved power conversion efficiency (PCE) of 18.04% under air conditions, which is comparable to that of the cell employing the commonly used Spiro-OMeTAD (18.27%), while HT1-based cell showed a slightly worse performance with a PCE of 17.18%. For ssDSCs, the HT2-based device yielded a PCE of 6.35%, which is also comparable to that of a cell fabricated based on Spiro-OMeTAD (6.36%). We found that the larger dimensional structure and molecular weight of HT2 enable better photovoltaic performance than that of the smaller one HT1. These results show that easily synthesized fluorene-based HTMs have great potential to replace the expensive Spiro-OMeTAD for both PSCs and ssDSCs.
|
|
| 10. |
- Marinado, Tannia, et al.
(författare)
-
Surface Molecular Quantification and Photoelectrochemical Characterization of Mixed Organic Dye and Coadsorbent Layers on TiO2 for Dye-Sensitized Solar Cells
- 2010
-
Ingår i: The Journal of Physical Chemistry C. - : American Chemical Society (ACS). - 1932-7447 .- 1932-7455. ; 114:27, s. 11903-11910
-
Tidskriftsartikel (refereegranskat)abstract
- Different molecular layers on TiO2 were prepared by using the p-dimethylaniline triphenylamine based organic dye, D29, together with the coadsorbents decylphosphonic acid (DPA), dineohexyl bis(3,3-dimethylbutyl)phosphinic acid (DINHOP), and chenodeoxycholic acid (CDCA). The surface molecular structure of dye and coadsorbent layers on TiO2 was investigated by photoelectron spectroscopy (PES). A focus was to determine the surface molecular concentrations using characteristic photoelectron core levels. Dye-sensitized solar cells (DSCs) were prepared from the same substrate and were further characterized by photoelectrochemical methods. Together the investigation gives information on the arrangement of the mixed molecular layer and a first insight to the extent to which the coadsorbents exchange with dye molecules on the TiO2 surface for the examined conditions.
|
|
