| 1. |
- Ahmed, Sheikh Ali, et al.
(författare)
-
Anatomical properties and process parameters affecting blister/blow formation in densified European aspen and downy birch sapwood boards by thermo-hygro-mechanical compression
- 2013
-
Ingår i: Journal of Materials Science. - : Springer Science and Business Media LLC. - 0022-2461 .- 1573-4803. ; 48:24, s. 8571-8579
-
Tidskriftsartikel (refereegranskat)abstract
- Approximately, 13.5 % of the standing volume of productive forest land in Sweden is covered by birch and aspen, which provides the vast potential to produce value-added products such as densified wood. This study shows whether it is possible to densify those species with a thermo-hygro-mechanical (THM) process using heat, steam, and pressure. In this process, transverse compression on thin European aspen (Populus tremula) and downy birch (Betula pubescens) boards was performed at 200 ºC with a maximum steam pressure of 550 kPa. To obtain a theoretical 50 % compression set, the press’s maximum hydraulic pressure ranged from 1.5 to 7.3 MPa. Preliminary tests showed that ~75 % of the birch boards produced defects (blisters/blows) while only 25 % of the aspen boards did. Mainly, radial delamination associated with internal checks in intrawall and transwall fractures caused small cracks (termed blisters) while blows are characterized by relatively larger areas of delamination visible as a bumpy surface on the panel. Anatomical investigations revealed that birch was more prone to those defects than aspen. However, those defects could be minimized by increasing the pre-treatment time during the THM processing.
|
|
| 2. |
- Ananías, Rubén A., et al.
(författare)
-
Collapse of Eucalyptus nitens Wood after Drying Depending on the Radial Location Within the Stem
- 2014
-
Ingår i: Drying Technology. - : Informa UK Limited. - 0737-3937 .- 1532-2300. ; 32:14, s. 1699-1705
-
Tidskriftsartikel (refereegranskat)abstract
- Collapse is almost certain to occur in the industrial drying of Eucalyptus nitens, and as such this prevents the lumber manufacturing industry in Chile from producing commercial solid wood products from this species. This problem is still unsolved, and different studies to reduce collapse are currently underway. In this exploratory study, shrinkage and collapse after drying of Eucalyptus nitens was measured for boards cut from different radial locations within the stem (core, transition and outer wood from pith to bark) and having different annual ring orientation (flat-sawn and quarter-sawn). Even though exploratory, the results appear to confirm that pieces that were cut from the center of the trees were less susceptible to collapse than the pieces cut from the transition zone between the center and the periphery. On average, collapse in transition wood was approximately 50% higher than the collapse observed in wood cut from the central zone of the trees.
|
|
| 3. |
|
|
| 4. |
|
|
| 5. |
|
|
| 6. |
|
|
| 7. |
- Elustondo, Diego, et al.
(författare)
-
Drying Western Red Cedar with Superheated Steam
- 2014
-
Ingår i: Drying Technology. - : Informa UK Limited. - 0737-3937 .- 1532-2300. ; 32:5, s. 550-556
-
Tidskriftsartikel (refereegranskat)abstract
- This exploratory study evaluated the possibility of drying 50-mm-thick western red cedar with superheated steam. Since there are no industrial facilities in Canada drying western red cedar with superheated steam, the study was designed to explore the potential of this technology in terms of lumber quality, moisture content distribution, and drying time. The experiments showed that the 50-mm-thick product can be dried in less than three days without jeopardizing lumber quality (in comparison with the two weeks that is currently required in conventional kilns), and the percentage of pieces that remained wet after drying was within the 10% to 15% range that is typically tolerated in industry.
|
|
| 8. |
- Elustondo, Diego, et al.
(författare)
-
Drying with superheated steam : Maximum drying rate as a linear function of pressure
- 2002
-
Ingår i: Chemical Engineering Journal. - 1385-8947 .- 1873-3212. ; 86:1-2, s. 69-74
-
Tidskriftsartikel (refereegranskat)abstract
- Drying with superheated steam (SS) as heating agent is controlled through three operative variables, the steam temperature, the recycle velocity, and the system pressure. Once the other conditions are fixed, there is an optimum pressure at which drying rate reaches its maximum value. The exact optimum conditions can be found through a differential mass and energy balance over the heat exchange area, resulting in two equations. The first one to calculate the drying rate as function of the operating conditions and the second one to find the values of those conditions which make the operation optimum. Then, using these equations, this paper shows that the relationship between maximum drying rate and pressure can be rewritten in a unique linear equation. Experiments were performed in a model system to obtain a family of drying rates versus pressure curves, and in accordance with the predicted behaviour, it was observed that all maximum drying rates lay on a straight line
|
|
| 9. |
- Elustondo, Diego, et al.
(författare)
-
Evaluation of three semi-empirical models for superheated steam vacuum drying of timbers
- 2003
-
Ingår i: Drying Technology. - 0737-3937 .- 1532-2300. ; 21:5, s. 875-893
-
Tidskriftsartikel (refereegranskat)abstract
- Superheated steam drying at sub-atmospheric pressure (SSV) has been successfully employed in Europe and Asia for drying some types of timbers, showing that drying time could be reduced by 50% with respect to conventional drying without significant losses in the quality of the final product. This reduction is the consequence of a different heat and mass transfer control mechanism. Since SSV drying is carried out in absence of gaseous air, diffusion of the generated vapor is not a limiting factor and drying rate becomes more dependent on heat transference. Therefore, classical interpretation of timber drying as a process based on moisture migration control is not applicable to SSV. This work is targeting the development and validation of a simplified semi-empirical model for SSV drying of timbers. Mathematical representation of the proposed model is uncomplicated and straightforward to apply, and the comparison between model predicted and experimental data showed a high degree of agreement under variable drying conditions.
|
|
| 10. |
|
|
