| 1. |
- Xu, Yunsheng, et al.
(författare)
-
Methacrylated lignosulfonate as compatibilizer for flax fiber reinforced biocomposites with soybean-derived polyester matrix
- 2020
-
Ingår i: Composites Communications. - : Elsevier BV. - 2452-2139.
-
Tidskriftsartikel (refereegranskat)abstract
- The poor adhesion between natural fibers and polymer matrix restricts the mechanical performance of natural fiber reinforced composites. Here, lignosulfonate was methacrylated and evaluated as a potential compatibilizer for flax fiber reinforced soybean-derived polyester thermosets. Significant improvement in both tensile and flexural properties of the fiber composites were achieved when the flax fiber mat was treated with methacrylated lignosulfonate solution. In particular, the flexural modulus and flexural strength more than doubled from 2.6 to 6.7 GPa and from 36 MPa to 76.8 MPa, respectively when the fibers were soaked in 5 wt % MLS solution. The SEM analysis revealed improved fiber-matrix interface and lower extent of fiber pull-out in the methacrylated lignosulfonate treated fiber composites, which correlates with the improved mechanical properties.
|
|
| 2. |
- Noè, C., et al.
(författare)
-
Frontal-Photopolymerization of Fully Biobased Epoxy Composites
- 2022
-
Ingår i: Macromolecular materials and engineering. - : Wiley. - 1438-7492 .- 1439-2054. ; 307:6, s. 2100864-
-
Tidskriftsartikel (refereegranskat)abstract
- The radical-induced cationic frontal photopolymerization (RICFP) of fully biobased epoxy composites is successfully demonstrated. This curing strategy considerably reduces the curing time and improves the efficiency of the composite fabrication. Two different natural fiber fabrics made of cellulose and flax fibers are embedded in two epoxy matrices, one derived from vanillin (diglycidylether of vanillyl alcohol-DGEVA) and the other from petroleum (3,4-epoxycyclohexylmethyl 3,4-epoxycyclohexanecarboxylate-CE). After RICFP the composites are characterized by means of dynamic mechanical thermal analysis and tensile tests. The mechanical properties improved with increasing fiber content, confirming a strong adhesion between the matrix and the reinforcing fiber fabrics, which is further evidenced by scanning electron microscopy analyses of the fracture surfaces. Furthermore, these fully bio-based composites possess comparable or even higher mechanical strength compared with the corresponding epoxy composites fabricated with conventional CE resin. A promising facile route to high-performing natural fiber-biobased epoxy resin composites is presented.
|
|
| 3. |
- Seoane, Fernando, et al.
(författare)
-
Conductive Polymer Films as Textrodes for Biopotential Sensing
- 2011
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- Introduction: After several years of progresses in textile technology and wearable measurement instrumentation, applications of wearable textile-electronics systems are arising providing a stable background for commercial applications. So far, the available commercial solutions are centered on fitness applications and mostly based in the acquisition of heart rate through Textile Electrodes (Textrodes) based on metallic threads or on conductive rubber compounds. Methods and Materials: In this work a novel material approach is presented to produce Textrodes for acquisition of Electrocardiographic (ECG) signals using a conductive polypropylene (PP1386 from Premix, Finland) polymer material. The polymer was film extruded into thin films, and used as such in the Textrode. Conductive Polymer Films (CPF) have been used to produce Textrodes, and its measurement performance has been compared with the ECG signals obtained with commercial Textrode fabrics and conventional Ag/AgCl electrodes. In order to set up the same measurement conditions, a chest strap tailored to host the testing electrodes has been used. Results: The close resemblance of the ECG acquired with the textile fabric electrodes, the Ag/AgCl electrodes and the PP1386 CPF electrodes suggest that the Polymer Electrodes PP1386 are a feasible alternative to the current textile fabrics that use silver thread as conductive material and also to conductive rubber material. Discussion & Conclusion: The availability of the Conductive Polymer Electrode PP1386 in a film form allows the manufacturing of electrodes by conventional textile processes, like lamination or sewing, therefore facilitating the transition from lab prototyping to industrial manufacturing. Replacing the traditional silver thread as conductive element in the fabrication of Textrodes will definitely reduce the material cost per Textrode. Biocompatibility issues and manufacturability issues must be addressed but the exhibited functional performance is showing encouraging results.
|
|
| 4. |
- Kumar Ramamoorthy, Sunil, 1987-, et al.
(författare)
-
End of life textiles as reinforcements in biocomposites
- 2017
-
Ingår i: Journal of Polymers and the Environment. - : Springer. - 1566-2543 .- 1572-8919 .- 1572-8900. ; , s. -12
-
Tidskriftsartikel (refereegranskat)abstract
- A number of attempts have been made to recycle cotton/polyester blend woven fabrics after use; however, most of these fabrics are disposed of in landfills. Major part of these blend fabrics are not recycled due to complexity of the fibre arrangement and cannot be separated economically. This study shows that these discarded woven fabrics could be directly used as reinforcements in composites without fibre separation. Uniform alignment in the woven fabric provided consistent properties to the composites. The fabrics were reinforced by soybean-based-bioresins to produce biocomposites. The composites were analysed for mechanical, thermal, viscoelastic and morphological properties. Porosity and wettability of the composites were also evaluated. Results demonstrate that the tensile strength and modulus of over 100 and 10 MPa, respectively, can be obtained without any fibre treatment. Furthermore, impact strength over 70 kJ/m2 was obtained without any chemical treatment on fibres. The porosity of the composites produced was less than 9 vol%. Additionally, the fabrics were treated with alkali in order to improve the fibre–matrix interface and the composite properties were studied. From the economical perspective, these composites can be produced at a low cost as the major component is available for free or low cost.
|
|
| 5. |
- Darabi, Sozan, 1994, et al.
(författare)
-
Green Conducting Cellulose Yarns for Machine-Sewn Electronic Textiles
- 2020
-
Ingår i: ACS Applied Materials & Interfaces. - : American Chemical Society (ACS). - 1944-8252 .- 1944-8244. ; 12:50, s. 56403-56412
-
Tidskriftsartikel (refereegranskat)abstract
- The emergence of "green"electronics is a response to the pressing global situation where conventional electronics contribute to resource depletion and a global build-up of waste. For wearable applications, green electronic textile (e-textile) materials present an opportunity to unobtrusively incorporate sensing, energy harvesting, and other functionality into the clothes we wear. Here, we demonstrate electrically conducting wood-based yarns produced by a roll-to-roll coating process with an ink based on the biocompatible polymer:polyelectrolyte complex poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS). The developed e-textile yarns display a, for cellulose yarns, record-high bulk conductivity of 36 Scm-1, which could be further increased to 181 Scm-1 by adding silver nanowires. The PEDOT:PSS-coated yarn could be machine washed at least five times without loss in conductivity. We demonstrate the electrochemical functionality of the yarn through incorporation into organic electrochemical transistors (OECTs). Moreover, by using a household sewing machine, we have manufactured an out-of-plane thermoelectric textile device, which can produce 0.2 μW at a temperature gradient of 37 K.
|
|
| 6. |
- Erem, Aysin, et al.
(författare)
-
In vitro assesment of antimicrobial activity and characteristics of polyamide 6/silver nanocomposite fibers
- 2013
-
Ingår i: Fibers And Polymers. - : Elsevier. - 1229-9197 .- 1875-0052. ; 14:9, s. 1415-1421
-
Tidskriftsartikel (refereegranskat)abstract
- In this study, the preparation method and characteristics of silver (Ag) nanoparticle (NP) loaded polyamide 6 (PA6) nanocomposite and its antimicrobial activity against Klebsiella pneumonia and Staphylococcus aureus were investigated. The melt intercalation method was used to prepare a series of PA 6 nanocomposite fibers containing, 0; 1; 3; 5 % (wt.) Ag. PA6/Ag nanocomposite fibers exhibit increased antimicrobial efficiency with the increase of nanoparticle contents. On the other hand, thermal characterization tests show that the increased concentration of Ag nanoparticles reduces the mechanical properties due to their partial agglomeration leading to flaw generation. The crystallinity of the fibers was found to decrease about 10 % with increase of Ag to 5 %. This was attributed to faster cooling rate experienced in the presence of high thermal conductivity Ag particles.
|
|
| 7. |
- Mehrjerdi, A. K., et al.
(författare)
-
Mechanical and thermo-physical properties of high-density polyethylene modified with talc
- 2013
-
Ingår i: Journal of Applied Polymer Science. - : Wiley. - 1097-4628 .- 0021-8995. ; 129:4, s. 2128-2138
-
Tidskriftsartikel (refereegranskat)abstract
- The aim of this study was to examine the physical, mechanical, and thermo-physical properties of high-density polyethylene (HDPE) modified with talc. Different weight fractions of talc (up to 35 wt %) were compounded with an HDPE matrix containing 2.5 wt % of carbon black (CB) in a twin-screw compounder. The composites were then processed by injection moulding to obtain specimens for testing. The results indicate that CB causes a significant decrease in the toughness, while talc not only enhances the thermal conductivity and thermo-physical properties of the composites but can also play a role in compensating for the negative effects of CB on impact resistance. The experimental data show that the presence of CB reduces the impact resistance of HDPE by up to 34%, while addition of up to 8 wt % talc can return this value to close to that of pure HDPE. No significant effect on the composite tensile yield and fracture strength was observed for either component at all concentrations. The thermal conductivity, thermal diffusivity, and specific density values of the composites increased almost linearly, but the increase in moisture absorption in the long term showed nonlinear behavior in the concentration range of the experiment.
|
|
| 8. |
- Rajan, Rathish, et al.
(författare)
-
Effect of viscose fabric modification on the mechanical and water absorption properties of composites prepared through vacuum infusion
- 2014
-
Ingår i: Journal of reinforced plastics and composites (Print). - : Sage Publications Ltd.. - 0731-6844 .- 1530-7964. ; 33:15, s. 1416-1429
-
Tidskriftsartikel (refereegranskat)abstract
- Viscose fabric-reinforced unsaturated polyester composites were successfully prepared through vacuum infusion process. Unidirectional viscose fabric was modified by two different organosilane coupling agents and by acetylation treatment. The main objective was to study the influence of fabric treatment on the mechanical and water absorption properties of the composites. Flexural, tensile and impact properties of composites were studied. The results from mechanical testing of composites pointed out that 3-aminopropyltriethoxy silane treatment increased the flexural and impact strengths of the composites with respect to untreated fabric composite. The impact strength of 3-aminopropyltriethoxy silane-treated fabric composites almost doubled compared to the value of untreated fabric composite. Among all the composites under study, those with fabrics treated by 2 vol% 3-aminopropyltriethoxy silane in ethanol/water (95:5) solution exhibited significant improvement in water uptake resistance. An unsaturated polyester gelcoat and topcoat were applied as the outer surface on the composites with untreated fabric. This was done in order to investigate the visual surface appearance and evaluate the gelcoat and topcoat effect on water absorption after accelerated water immersion test. The regenerated cellulose fibre as reinforcement shows high potential to be used as an alternative for natural bast fibres, especially, when toughness of material matters. Chemical treatment of regenerated cellulose fibres could result in improvement in properties of polymer composites, considering that the appropriate treatment method is selected for the corresponding fibre–matrix system.
|
|
| 9. |
- Ramamoorthy, Sunil Kumar, 1987-, et al.
(författare)
-
Performance of biocomposites from surface modified regenerated cellulose fibers and lactic acid thermoset bioresin
- 2015
-
Ingår i: Cellulose. - : Springer Science and Business Media LLC. - 0969-0239 .- 1572-882X.
-
Tidskriftsartikel (refereegranskat)abstract
- The effect of surface treatments, silane and alkali, on regenerated cellulose fibers was studied by using the treated fibers as reinforcement in lactic acid thermoset bioresin. The surface treatments were performed to improve the physico–chemical interactions at the fiber–matrix interface. Tensile, flexural and impact tests were used as indicator of the improvement of the interfacial strength. Furthermore, thermal conductivity, viscoelasticity measurements as well as microscopy images were made to characterize the fiber surface treatments and the effect on adhesion to the matrix. The results showed that silane treatment improved the mechanical properties of the composites as the silane molecule acts as link between the cellulose fiber and the resin (the fiber bonds with siloxane bridge while the resin bonds with organofunctional group of the bi-functional silane molecule) which gives molecular continuity in the interphase of the composite. Porosity volume decreased significantly on silane treatment due to improved interface and interlocking between fiber and matrix. Decrease in water absorption and increase in contact angle confirmed the change in the hydrophilicity of the composites. The storage modulus increased when the reinforcements were treated with silane whereas the damping intensity decreased for the same composites indicating a better adhesion between fiber and matrix on silane treatment. Thermogravimetric analysis indicated that the thermal stability of the reinforcement altered after treatments. The resin curing was followed using differential scanning calorimetry and the necessity for post-curing was recommended. Finite element analysis was used to predict the thermal behavior of the composites and a non-destructive resonance analysis was performed to ratify the modulus obtained from tensile testing. The changes were also seen on composites reinforced with alkali treated fiber. Microscopy images confirmed the good adhesion between the silane treated fibers and the resin at the interface.
|
|
| 10. |
|
|
