| 1. |
- Kersten, Anton, 1991, et al.
(författare)
-
Measuring and Separating Conducted Three-Wire Emissions from a Fault-Tolerant, NPC Propulsion Inverter with a Split-Battery Using Hardware Separators Based on HF Transformers
- 2021
-
Ingår i: IEEE Transactions on Power Electronics. - 0885-8993 .- 1941-0107. ; 36:1, s. 378-390
-
Tidskriftsartikel (refereegranskat)abstract
- Conducted emissions on the traction battery's power cables in EVs must be limited to avoid unwanted electromagnetic interference (EMI). When designing an EMI filter, it is advantageous to have information of the common mode (CM) and differential mode (DM) noise levels. This article deals with the measurement and separation of the dc side's three-wire DM/CM noise of a fault-tolerant three-level neutral-point-clamped (NPC) inverter with a split-battery system. Two hardware separators, based on small-circuit highfrequency transformers, were developed to identify the dc side's CM, line-DM, and phase-DM noise levels. Their characterized CM and DM rejection ratios for the frequency range from 150 kHz to 110 MHz are at least -33 and -21 dB, respectively. The separated noise of the NPC inverter was measured, using an inductive load, when operating the inverter with three-level and two-level modulation, resembling normal operation and a possible operation under fault, respectively. A simple three-wire CM model of the used testbed and the DM power module oscillation were derived to validate the separated noise's resonance peaks/valleys. It has been seen that the CM noise is dominant, especially below 10 MHz, except for the power module oscillations. Furthermore, when using the two-level modulation, in the case of a clamping diode fault, the noise levels are increased by about 3 dB.
|
|
| 2. |
- Kersten, Anton, 1991
(författare)
-
Modular Battery Systems for Electric Vehicles based on Multilevel Inverter Topologies - Opportunities and Challenges
- 2021
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Modular battery systems based on multilevel inverter (MLI) topologies can possibly overcome some shortcomings of two-level inverters when used for vehicle propulsion. The results presented in this thesis aim to point out the advantages and disadvantages, as well as the technical challenges, of modular vehicle battery systems based on MLIs in comparison to a conventional, two-level IGBT inverter drivetrain. The considered key aspects for this comparative investigation are the drive cycle efficiency, the inverter cost, the fault tolerance capability of the drivetrain and the conducted electromagnetic emissions. Extensive experiments have been performed to support the results and conclusions. In this work, it is shown that the simulated drive cycle efficiency of different low-voltage-MOSFET-based, cascaded seven-level inverter types is improved in comparison to a similarly rated, two-level IGBT inverter drivetrain. For example, the simulated WLTP drive cycle efficiency of a cascaded double-H-bridge (CDHB) inverter drivetrain in comparison to a two-level IGBT inverter, when used in a small passenger car, is increased from 94.24% to 95.04%, considering the inverter and the ohmic battery losses. In contrast, the obtained efficiency of a similar rated seven-level cascaded H-bridge (CHB) drivetrain is almost equal to that of the two-level inverter drivetrain, but with the help of a hybrid modulation technique, utilizing fundamental selective harmonic elimination at lower speeds, it could be improved to 94.85%. In addition, the CDHB and CHB inverters’ cost, in comparison to the two-level inverter, is reduced from 342€ to 202€ and 121€, respectively. Furthermore, based on a simple three-level inverter with a dual battery pack, it is shown that MLIs inherently allow for a fault tolerant operation. It is explained how the drivetrain of a neutral point clamped (NPC) inverter can be operated under a fault condition, so that the vehicle can drive with a limited maximum power to the next service station, referred to as limp home mode. Especially, the detection and localization of open circuit faults has been investigated and verified through simulations and experiments. Moreover, it is explained how to measure the conducted emissions of an NPC inverter with a dual battery pack according to the governing standard, CISPR 25, because the additional neutral point connection forms a peculiar three-wire DC source. To separate the measured noise spectra into CM, line-DM and phase-DMquantities, two hardware separators based on HF transformers are developed and utilized. It is shown that the CM noise is dominant. Furthermore, the CM noise is reduced by 3dB to 6dB when operating the inverter with three-level instead of two-level modulation.
|
|
| 3. |
- Kersten, Anton, 1991, et al.
(författare)
-
Online and On-Board Battery Impedance Estimation of Battery Cells, Modules or Packs in a Reconfigurable Battery System or Multilevel Inverter
- 2020
-
Ingår i: IECON Proceedings (Industrial Electronics Conference). - 2162-4704 .- 2577-1647. ; 2020-October, s. 1884-1891
-
Konferensbidrag (refereegranskat)abstract
- This paper shows two approaches to determine the battery impedance of battery cells or battery modules when used in a reconfigurable battery system (RBS) or in any type of modular multilevel converter (MMC) for electric drive applications. A generic battery model is used and the concepts of the recursive time and frequency-domain parameter extraction, using a current step and an electrochemical impedance spectroscopy, are explained. Thus, it is shown and demonstrated that the balancing current of neighboring cells/modules ,when in parallel operation, can be used, similar to the time-domain parameter extraction utilizing a current step, to determine the battery parameters. Furthermore, it is shown and demonstrated that a part of the inverter can be used as variable AC voltage source to control a sinusoidal current through the motor inductances of the drive train, which can be injected to the inserted battery cells/modules of an adjacent phase to perform an on-board impedance spectroscopy. Using either of the two presented approaches, the individual battery impedances can be easily determined, yielding the state of health (SOH) and the power capability of individual battery cells/modules. Nonetheless, the analyzed approaches were just considered to be applied at machine standstill, which is not suitable for grid-tied applications.
|
|
| 4. |
- Theliander, Oskar, et al.
(författare)
-
Battery Modeling and Parameter Extraction for Drive Cycle Loss Evaluation of a Modular Battery System for Vehicles Based on a Cascaded H-Bridge Multilevel Inverter
- 2020
-
Ingår i: IEEE Transactions on Industry Applications. - 0093-9994 .- 1939-9367. ; 56:6, s. 6968-6977
-
Tidskriftsartikel (refereegranskat)abstract
- This article deals with the modeling and the parameterization of the battery packs used in cascaded H-bridge multilevel propulsion inverters. Since the battery packs are intermittently conducting the motor currents, the battery cells are stressed with a dynamic current containing a substantial amount of low-order harmonic components up to a couple of kHz, which is a major difference in comparison to a traditional two-level inverter drive. Different models, such as pure resistive and dynamic RC -networks, are considered to model the energy losses for different operating points (OPs) and driving cycles. Using a small-scale setup, the models’ parameters are extracted using both a low-frequency, pulsed current, and an electrochemical impedance spectroscopy (EIS) sweep. The models are compared against measurements conducted on the small-scale setup at different OPs. Additionally, a drive cycle loss comparison is simulated. The simple resistive model overestimates the losses by about 20% and is, thus, not suitable. The dynamic three-time-constant model, parameterized by a pulsed current, complies with the measurements for all analyzed OPs, especially at low speed, with a maximum deviation of 3.8%. Extracting the parameters using an EIS seems suitable for higher speeds, though the losses for the chosen OPs are underestimated by 1.5%–7.9%.
|
|
| 5. |
- Kruglov, Dmitrii, 1994, et al.
(författare)
-
Enhancing mmWave On-Chip-Antennas Using In-Package Electromagnetic Bandgap Structures
- 2021
-
Ingår i: European Microwave Conference. - 1527-3342 .- 1557-9581. - 9782874870637 ; , s. 885-888
-
Konferensbidrag (refereegranskat)abstract
- We propose a silicon on-Chip-in-Package antenna design featuring a simulated radiation efficiency of > 70% and an S11 matching better than −10 dB in the 112–125 GHz frequency range. High radiation performance is achieved by: (i) thinning the silicon substrate down to 100 μm through wafer-level grinding; (ii) embedding the IC in-between two PCBs, one of which forms an electromagnetic bandgap structure that attenuates the EM leakage inside the silicon substrate. Furthermore, since the die-embedding concept employs the gap-waveguide packaging technology, a universal contactless waveguide interconnect is realized between the IC and the radiating gap waveguide in the package. This will also enable modular antenna designs.
|
|
| 6. |
- Gülgün, Ziya, et al.
(författare)
-
Multiple Spoofer Detection for Mobile GNSS Receivers Using Statistical Tests
- 2021
-
Ingår i: IEEE Access. - : Institute of Electrical and Electronics Engineers (IEEE). - 2169-3536. ; 9, s. 166382-166394
-
Tidskriftsartikel (refereegranskat)abstract
- We consider Global Navigation Satellite Systems (GNSS) spoofing attacks and devise a countermeasure appropriate for mobile GNSS receivers. Our approach is to design detectors that, operating after the signal acquisition, enable the victim receiver to determine with high probability whether it is under a spoofing attack or not. Namely, the binary hypothesis is that either the GNSS receiver tracks legitimate satellite signals, H-0, or spoofed signals, H-1. We assume that there exists an unknown number of multiple spoofers in the environment and the attack strategy (which legitimate signals are spoofed by which spoofers) is not known to the receiver. Based on these assumptions, we propose an algorithm that identifies the number of spoofers and clusters the spoofing data by using Bayesian information criterion (BIC) rule. Depending on the estimated and clustered data we propose a detector, called as generalized likelihood ratio (GLRT)-like detector. We compare the performance of the GLRT-like detector with a genie-aided detector in which the attack strategy and the number of spoofers is known by the receiver. In addition to this, we extend the GLRT-like detector for the case where the noise variance is also unknown and present the performance results.
|
|
| 7. |
- Schilliger Kildal, Madeleine, 1987, et al.
(författare)
-
Verification of the Random Line-of-Sight Measurement Setup at 1.5-3 GHz including MIMO Throughput Measurements of a Complete Vehicle
- 2020
-
Ingår i: IEEE Transactions on Vehicular Technology. - 0018-9545 .- 1939-9359. ; 69:11, s. 13165-13179
-
Tidskriftsartikel (refereegranskat)abstract
- The performance evaluation of wireless systems is crucial for the development of future systems with more connected devices. It is essential to have an easy and relevant method for ensuring the wireless communication performance of the devices. We have recently developed a new random line-of-sight (random-LOS) measurement system for evaluating the communication performance of wireless devices, e.g., transceivers and antennas installed on a vehicle. In the measurement system, a plane wave is generated in the test zone emulating the far-field wave transmitted from a radio base station. In this paper we present both numerical simulations and actual experimental results of the random-LOS over-the-air (OTA) measurement setup operating in the 1.5-3 GHz band. The measurement accuracy is determined by the field variations within the test zone, where a smaller variation gives better measurement accuracy. In this paper the achieved accuracy expressed in terms of standard deviation (STD) was evaluated to be approximately 1 dB of the power within a cylindrical test zone of height 0.4 m and diameter 2 m. The active multiple-input multiple-output (MIMO) performance of antenna systems installed on an actual vehicle was measured and evaluated using the presented setup. A comparison to a theoretical zero forcing (ZF) receiver is also presented.
|
|
| 8. |
- Zhang, Kewei
(författare)
-
Secure GNSS-based Positioning and Timing : Distance-Decreasing attacks, fault detection and exclusion, and attack detection with the help of opportunistic signals
- 2021
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- With trillions of devices connected in large scale systems in a wired or wireless manner, positioning and synchronization become vital. Global Navigation Satellite System (GNSS) is the first choice to provide global coverage for positioning and synchronization services. From small mobile devices to aircraft, from intelligent transportation systems to cellular networks, and from cargo tracking to smart grids, GNSS plays an important role, thus, requiring high reliability and security protection. However, as GNSS signals propagate from satellites to receivers at distance of around 20 000 km, the signal power arriving at the receivers is very low, making the signals easily jammed or overpowered. Another vulnerability stems from that civilian GNSS signals and their specifications are publicly open, so that anyone can craft own signals to spoof GNSS receivers: an adversary forges own GNSS signals and broadcasts them to the victim receiver, to mislead the victim into believing that it is at an adversary desired location or follows a false trajectory, or adjusts its clock to a time dictated by the adversary. Another type of attack is replaying GNSS signals: an adversary transmits a pre-recorded GNSS signal stream to the victim receiver, so that the receiver calculates an erroneous position and time. Recent incidents reported in press show that the GNSS functionalities in a certain area, e.g., Black Sea, have been affected by cyberattacks composed of the above-mentioned attack types. This thesis, thus, studies GNSS vulnerabilities and proposes detection and mitigation methods for GNSS attacks, notably spoofing and replay attacks. We analyze the effectiveness of one important and powerful replay attack, the so-called Distance-decreasing (DD) attacks that were previously investigated for wireless communication systems, on GNSS signals. DD attacks are physical layer attacks, targeting time-of-flight ranging protocols, to shorten the perceived as measured distance between the transmitter and receiver. The attacker first transmits an adversary-chosen data bit to the victim receiver before the signal arrives at the attacker; upon receipt of the GNSS signal, the attacker estimates the data bit based on the early fraction of the bit period, and then switches to transmitting the estimate to the victim receiver. Consequently, the DD signal arrives at the victim receiver earlier than the genuine GNSS signals would have, which in effect shortens the pseudorange measurement between the sender (satellite) and the victim receiver, consequently, affecting the calculated position and time of the receiver. We study how the DD attacks affect the bit error rate (BER) of the received signals at the victim, and analyze its effectiveness, that is, the ability to shorten pseudorange measurements, on different GNSS signals. Several approaches are considered for the attacker to mount a DD attack with high probability of success (without being detected) against a victim receiver, for cryptographically unprotected and protected signals. We analyze the tracking output of the DD signals at the victim receiver and propose a Goodness of Fit (GoF) test and a Generalized Likelihood Ratio Test (GLRT) to detect the attacks. The evaluation of the two tests shows that they are effective, with the result being perhaps more interesting when considering DD attacks against Galileo signals that can be cryptographically protected. Moreover, this thesis investigates the feasibility of validating the authenticity of the GNSS signals with the help of opportunistic signals, which is information readily available in modern communication environments, e.g., 3G, 4G and WiFi. We analyze the time synchronization accuracy of different technologies, e.g., Network Time Protocol (NTP), WiFi and local oscillator, as the basis for detecting a discrepancy with the GNSS-obtained time. Two detection approaches are proposed and one testbench is designed for the evaluation. A synthesized spoofing attack is used to verify the effectiveness of the approaches. Beyond attack detection, we develop algorithms to detect and exclude faulty signals, namely the Clustering-based Solution Separation Algorithm (CSSA) and the Fast Multiple Fault Detection and Exclusion (FM-FDE). They both utilize the redundant available satellites, more than the minimum a GNSS receiver needs for position and time offset calculation. CSSA adopts data clustering to group subsets of positions calculated with different subsets of available satellites. Basically, these positions, calculated with subsets not containing any faulty satellites, should be close to each other, i.e., in a dense area; otherwise they should be scattered. FM-FDE is a more efficient algorithm that uses distances between positions, calculated with fixed-size subsets, as test statistics to detect and exclude faulty satellite signals. As the results show, FM-FDE runs faster than CSSA and other solution-separation fault detection and exclusion algorithms while remaining equally effective.
|
|
| 9. |
|
|
| 10. |
- Lu, Yang, et al.
(författare)
-
Mark ratio modulation over pulse position modulation
- 2020
-
Ingår i: Optical Fiber Technology. - : Elsevier BV. - 1095-9912 .- 1068-5200. ; 57
-
Tidskriftsartikel (refereegranskat)abstract
- Orthogonal modulation superimposes non-amplitude-modulated signals on Manchester coded or pulse position modulated amplitude shift keying (ASK) signals, allowing two traffic flows with different bit rates to be modulated on the same wavelength channel, and hence improving spectrum efficiency. Inspired by the orthogonal modulation, this paper proposes a novel modulation format, i.e., mark ratio modulation over pulse position modulation (PPM), which utilizes the mark ratio difference between the PPM symbols and the inverse PPM symbols to deliver an overlaid signal. Better than traditional orthogonal modulation, in the mark ratio modulation over PPM, both low-speed and high-speed traffic flows are modulated by ASK with no need to sacrifice the extinction ratio, while keeping the reception simple and easy. According to theoretical analysis and test, we found 4PPM is a good option, which can balance the trade-off between the PPM signal's effective bit rate and the mark ratio modulated signal's quality.
|
|
