| 1. |
- Karlsson, Olov, et al.
(author)
-
Heat treatments of high temperature dried norway spruce boards: Saccharides and furfurals in sapwood surfaces
- 2012
-
In: BioResources. - : BioResources. - 1930-2126 .- 1930-2126. ; 7:2, s. 2284-2299
-
Journal article (peer-reviewed)abstract
- Carbohydrates that migrate to wood surfaces in sapwood during drying might influence properties such as mould susceptibility and colour. Sugars on the surface of Norway spruce boards during various heat treatments were studied. Samples (350mm×125mm×25mm) were double-stacked, facing sapwood-side outwards, and dried at 110°C to a target moisture content (MC) of 40%. Dried sub-samples (80 mm × 125 mm × 25 mm) were stacked in a similar way and further heated at 110°C and at 130°C for 12, 24, and 36 hours, respectively. Glucose, fructose, and sucrose as well as 5-hydroxymethylfurfural (HMF) and furfural in the sapwood surface layer of treated wood were analysed using HPLC (RI- and UV-detectors). Carbohydrates degraded to a lower extent at 110°C than at 130°C. Furfural and to a larger extent HMF increased with treatment period and temperature. Heat treatment led to a decrease in lightness and hue of the sapwood surface of sub-samples, while chroma increased somewhat. Furthermore, considerably faster degradation (within a few minutes) of the carbohydrates on the surface of the dried spruce boards was observed when single sub-samples were conductively hot pressed at 200°C. Treatment period and initial MC influenced the presence of the carbohydrates in wood surface as well as colour change (ΔE ab) of the hot pressed sub-samples.
|
|
| 2. |
- Ahmed, Sheikh Ali, et al.
(author)
-
Uneven distribution of preservative in kiln-dried sapwood lumber of Scots pine : Impact of wood structure and resin allocation
- 2012
-
In: Holzforschung. - : Walter de Gruyter. - 0018-3830 .- 1437-434X. ; 66:2, s. 251-258
-
Journal article (peer-reviewed)abstract
- Scots pine (Pinus sylvestris L.) sapwood lumber was collected after kiln drying and preservative treatment with Celcure AC 800 (a copper-amine wood preservative). Distribution of the preservative throughout the lumber was visually examined. Not all, but some samples showed specific localized areas without any preservative distribution throughout their entire length. Those samples were assessed further for anatomical properties, specifically in impregnated and unimpregnated areas. Additional study was conducted on the morphological nature and redistribution of lipophilic extractives using three different histochemical staining methods. Intrinsic wood properties – especially the frequency of axial resin canals and the percentage of canals blocked – were found to be responsible for the irregular distribution of the preservative. Furthermore, the inability to create continuous and frequent interstitial spaces due to the collapse of thin-walled ray cells throughout the lumber resulted in un-even distribution of preservatives. Staining techniques were useful to localize places with more or less abundance of extractives (e.g., fats) in impregnated and unimpregnated wood, which varied considerably. Histochemical observations revealed information pertaining to the kiln dry specific distribution and redistribution of extractives between the areas. Moreover, resin reallocation and modification in ray parenchyma and resin canals induced by kiln drying would be another reason for the impregnation anomalies.
|
|
| 3. |
- Sehlstedt-Persson, Margot, et al.
(author)
-
Mold growth on sapwood boards exposed outdoors : the impact of wood drying
- 2011
-
In: Forest products journal. - : Forest Products Society. - 0015-7473. ; 61:2, s. 170-179
-
Journal article (peer-reviewed)abstract
- Mold growth on dried Norway spruce and Scots pine sapwood boards was investigated in an accelerated outdoor field test for 96 days. The boards were dried using three different methods of stacking: single stacking, double stacking with the sapwood sides in each pair facing toward each other, and double stacking with sapwood sides facing outward. Drying was performed at three temperatures: 25ºC, corresponding to air drying, and kiln drying at 70ºC and 110ºC. The degree of mold growth was visually assessed on both sides of each board. On average, pine boards showed a higher level of mold growth than the spruce boards. The highest average level of mold growth was found on the boards kiln dried at 708C, whereas the air-dried boards and the boards kiln dried at 110ºC showed considerably less mold growth. Stacking the boards during drying had a large impact on mold susceptibility of the sapwood. This study confirmed that, during the drying process, it is possible to direct the migration of nutrients in sapwood toward one chosen side of each board by double stacking; the opposite side leaches out, which has a great impact on surface mold growth. Chemical analyses of monosaccharide sugar gradients beneath the boards’ surfaces confirmed the results.
|
|
| 4. |
|
|
