Sökning: onr:"swepub:oai:DiVA.org:hv-18384" >
High Temperature Fa...
High Temperature Fatigue Performance of Electron Beam Powder Bed Fusion Manufactured Alloy 718
-
- Kjellsson, Henrik (författare)
- PTW,Univ West, Sweden
-
- Balachandramurthi, Arun Ramanathan, 1989- (författare)
- Högskolan Väst,Avdelningen för avverkande och additativa tillverkningsprocesser (AAT),PTW,Univ West, Sweden
-
- Moverare, Johan, Professor, 1973- (författare)
- Linköpings universitet,Högskolan Väst,Avdelningen för avverkande och additativa tillverkningsprocesser (AAT),Department of Management and Engineering, Linköping University, 58183, Linköping (SWE),PTW,Konstruktionsmaterial,Tekniska fakulteten,Univ West, Sweden
-
visa fler...
-
- Hansson, Thomas, 1964- (författare)
- Högskolan Väst,Avdelningen för avverkande och additativa tillverkningsprocesser (AAT),PTW,Univ West, Sweden; GKN Aerosp Sweden AB, Sweden
-
visa färre...
-
(creator_code:org_t)
- 2022-04-29
- 2022
- Engelska.
-
Ingår i: Metallurgical and Materials Transactions. A. - : Springer Nature. - 1073-5623 .- 1543-1940. ; 53, s. 2496-2514
- Relaterad länk:
-
https://doi.org/10.1...
-
visa fler...
-
https://hv.diva-port... (primary) (Raw object)
-
https://liu.diva-por... (primary) (Raw object)
-
https://urn.kb.se/re...
-
https://doi.org/10.1...
-
https://urn.kb.se/re...
-
visa färre...
Abstract
Ämnesord
Stäng
- The microstructure and mechanical properties of additively manufactured (AM) parts have been shown to be different from that of cast and wrought counterparts. In this study, electron beam powder bed fusion (EB-PBF) fabricated Alloy 718 was exposed to three different heat treatment routes followed by strain-controlled fatigue testing at 550 degrees C. The fatigue tests were performed with specimens built with their center axis parallel and transverse relative to the build direction. The microstructure showed saturated precipitation of delta-Ni3Nb after repeated solution treatment at 954 degrees C. In contrast, no delta-Ni3Nb precipitates could be observed after a single-step solution treatment at 1025 degrees C. However, the disparity of secondary phases showed no noticeable influence on the fatigue life. A significant difference in fatigue behavior was noted between the parallel and transverse directions. The specimens loaded parallel to the elongated grains showed on average similar to 5x greater life in comparison to the perpendicularly loaded specimens. Compared to corresponding heat-treated material conditions tested at ambient temperature, the specimens showed lower life at high strain amplitude and superior life at low strain amplitude. Moreover, competitive internal and surface failure modes were observed at the lower strain amplitudes while for the higher strain ranges, surface failure modes dominated. (C) The Author(s) 2022
Ämnesord
- TEKNIK OCH TEKNOLOGIER -- Materialteknik -- Bearbetnings-, yt- och fogningsteknik (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Materials Engineering -- Manufacturing, Surface and Joining Technology (hsv//eng)
- TEKNIK OCH TEKNOLOGIER -- Materialteknik -- Annan materialteknik (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Materials Engineering -- Other Materials Engineering (hsv//eng)
Nyckelord
- Fatigue of materials; Fatigue testing; Microstructure
- Production Technology
- Produktionsteknik
- Production Technology
- Produktionsteknik
Publikations- och innehållstyp
- ref (ämneskategori)
- art (ämneskategori)
Hitta via bibliotek
Till lärosätets databas