Sökning: onr:"swepub:oai:DiVA.org:hv-9324" >
Influence of cuttin...
Influence of cutting edge geometry on force build-up process in intermittent turning
-
- Agic, Adnan, 1967- (författare)
- University College West,Högskolan Väst,Avdelningen för avverkande och additativa tillverkningsprocesser (AAT),Seco Tools AB, Fagersta, Sweden ; Department of Engineering Science, University West, Trollhättan, Sweden,PTW
-
- Gutnichenko, O. (författare)
- Lund University,Lunds universitet,Industriell Produktion,Institutionen för maskinvetenskaper,Institutioner vid LTH,Lunds Tekniska Högskola,Production and Materials Engineering,Department of Mechanical Engineering Sciences,Departments at LTH,Faculty of Engineering, LTH
-
- Eynian, Mahdi, 1980- (författare)
- University College West,Högskolan Väst,Avdelningen för avverkande och additativa tillverkningsprocesser (AAT),PTW,Department of Engineering Science, University West, Trollhättan, Sweden
-
visa fler...
-
- Ståhl, J. E. (författare)
- Lund University,Lunds universitet,Industriell Produktion,Institutionen för maskinvetenskaper,Institutioner vid LTH,Lunds Tekniska Högskola,Production and Materials Engineering,Department of Mechanical Engineering Sciences,Departments at LTH,Faculty of Engineering, LTH
-
visa färre...
-
(creator_code:org_t)
- Elsevier BV, 2016
- 2016
- Engelska.
-
Ingår i: Procedia CIRP. - : Elsevier BV. - 2212-8271 .- 2212-8271. ; 46, s. 364-367
- Relaterad länk:
-
https://doi.org/10.1...
-
visa fler...
-
https://doi.org/10.1...
-
https://his.diva-por... (primary) (Raw object)
-
http://dx.doi.org/10... (free)
-
https://urn.kb.se/re...
-
https://doi.org/10.1...
-
https://urn.kb.se/re...
-
https://lup.lub.lu.s...
-
visa färre...
Abstract
Ämnesord
Stäng
- In the intermittent turning and milling processes, during the entry phase the cutting edges are subjected to high impact loads that can give rise to dynamical and strength issues which in general cause tool life reduction. In this study the effect of geometrical features of the cutting tool on the force generation during the entry phase is investigated. Cutting forces are measured by a stiff dynamometer at a high sampling frequency. In addition, the chip load area is analyzed and related to the measured cutting force. The results show that micro-geometrical features, in particular the protection chamfer, significantly affect the force generation during the entry phase.
Ämnesord
- TEKNIK OCH TEKNOLOGIER -- Maskinteknik -- Produktionsteknik, arbetsvetenskap och ergonomi (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Mechanical Engineering -- Production Engineering, Human Work Science and Ergonomics (hsv//eng)
- TEKNIK OCH TEKNOLOGIER -- Materialteknik -- Bearbetnings-, yt- och fogningsteknik (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Materials Engineering -- Manufacturing, Surface and Joining Technology (hsv//eng)
- TEKNIK OCH TEKNOLOGIER -- Materialteknik (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Materials Engineering (hsv//eng)
Nyckelord
- Cutting
- force
- edge
- chip
- turning
- dynamic
- Manufacturing and materials engineering
- Produktions- och materialteknik
- chip
- cutting
- dynamic
- edge
- force
- turning
Publikations- och innehållstyp
- ref (ämneskategori)
- art (ämneskategori)
Hitta via bibliotek
Till lärosätets databas