Sökning: onr:"swepub:oai:DiVA.org:liu-153292" >
Effect of Machining...
Effect of Machining Parameters on Cutting Force and Surface Integrity when High-Speed Turning AD730™ with PCBN Tools
-
- Chen, Zhe, 1987- (författare)
- Linköping University,Linköpings universitet,Konstruktionsmaterial,Tekniska fakulteten
-
- Peng, Ru Lin, 1960- (författare)
- Linköping University,Linköpings universitet,Konstruktionsmaterial,Tekniska fakulteten
-
- Zhou, Jinming (författare)
- Lund University,Lunds universitet,Industriell Produktion,Institutionen för maskinvetenskaper,Institutioner vid LTH,Lunds Tekniska Högskola,Production and Materials Engineering,Department of Mechanical Engineering Sciences,Departments at LTH,Faculty of Engineering, LTH
-
visa fler...
-
- M'Saoubi, Rachid (författare)
- Seco Tools AB, Fagersta, Sweden
-
- Gustafsson, David (författare)
- Siemens Industrial Turbomachinery AB, Finspång, Sweden
-
- Moverare, Johan, 1973- (författare)
- Linköping University,Linköpings universitet,Konstruktionsmaterial,Tekniska fakulteten
-
visa färre...
-
(creator_code:org_t)
- 2018-10-18
- 2019
- Engelska.
-
Ingår i: The International Journal of Advanced Manufacturing Technology. - : Springer London. - 0268-3768 .- 1433-3015. ; 100:9-12, s. 2601-2615
- Relaterad länk:
-
https://link.springe...
-
visa fler...
-
http://dx.doi.org/10... (free)
-
https://urn.kb.se/re...
-
https://doi.org/10.1...
-
https://lup.lub.lu.s...
-
visa färre...
Abstract
Ämnesord
Stäng
- The novel wrought nickel-based superalloy, AD 730™, is a good candidate material for turbine disc applications at high temperatures beyond 650 °C. The present study focuses on the machining performance of this newly developed alloy under high-speed turning conditions with advanced PCBN tools. Meanwhile, the machined surface integrity as influenced by cutting speed and feed rate was also investigated. The surface integrity was thoroughly characterized in terms of surface roughness and morphology, machining-induced plastic deformation, white layer formation, and residual stresses. It has been found that the cutting speed and feed rate had a strong effect on the cutting forces and resultant surface integrity. The cutting forces required when machining the alloy were gradually reduced with increasing cutting speed, while at 250 m/min and above, the flank tool wear became stronger which led to increased thrust force and feed force. A higher feed rate, on the other hand, always resulted in higher cutting forces. Increasing the cutting speed and feed rate in general deteriorated the surface integrity. High cutting speeds within the range of 200–250 m/min and a low feed rate of 0.1 mm/rev are preferable in order to implement more cost-effective machining without largely reducing the surface quality achieved. The formation of tensile residual stresses on the machined AD 730™, however, could be of a concern where good fatigue resistance is critical.
Ämnesord
- TEKNIK OCH TEKNOLOGIER -- Materialteknik (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Materials Engineering (hsv//eng)
- TEKNIK OCH TEKNOLOGIER -- Materialteknik -- Bearbetnings-, yt- och fogningsteknik (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Materials Engineering -- Manufacturing, Surface and Joining Technology (hsv//eng)
Nyckelord
- Nickel-based superalloy
- High-speed turning
- Cutting forces
- Surface integrity
- AD730
- Cubic boron nitride (CBN) tool
- AD 730™
- Cubic boron nitride (CBN) tool
- Cutting forces
- High-speed turning
- Nickel-based superalloy
- Surface integrity
Publikations- och innehållstyp
- ref (ämneskategori)
- art (ämneskategori)
Hitta via bibliotek
Till lärosätets databas