Sökning: onr:"swepub:oai:lup.lub.lu.se:1a50064f-87e6-4d69-8aca-2b14f463e517" >
Adhesive wear of Ti...
Adhesive wear of TiAlN coatings during low speed turning of stainless steel 316L
-
- Moreno, Maiara (författare)
- Lund University,Lunds universitet,Linköpings universitet,Linköping University,Nanostrukturerade material,Tekniska fakulteten,Seco Tools AB, Sweden; Lund Univ, Sweden,Industriell Produktion,Institutionen för maskinvetenskaper,Institutioner vid LTH,Lunds Tekniska Högskola,Production and Materials Engineering,Department of Mechanical Engineering Sciences,Departments at LTH,Faculty of Engineering, LTH
-
- Andersson, Jon M. (författare)
- Seco Tools AB
-
- M'Saoubi, Rachid (författare)
- Lund University,Lunds universitet,Industriell Produktion,Institutionen för maskinvetenskaper,Institutioner vid LTH,Lunds Tekniska Högskola,Production and Materials Engineering,Department of Mechanical Engineering Sciences,Departments at LTH,Faculty of Engineering, LTH,Seco Tools AB
-
visa fler...
-
- Kryzhanivskyy, Vyacheslav (författare)
- Seco Tools AB, Sweden
-
- Johansson-Jöesaar, Mats P., 1965- (författare)
- Linköpings universitet,Linköping University,Seco Tools AB, Sweden,Nanostrukturerade material,Tekniska fakulteten
-
- Johnson, Lars J.S. (författare)
- Sandvik Coromant AB,Sandvik Coromant, Sweden
-
- Odén, Magnus, 1965- (författare)
- Linköpings universitet,Linköping University,Nanostrukturerade material,Tekniska fakulteten
-
- Rogström, Lina (författare)
- Linköpings universitet,Linköping University,Nanostrukturerade material,Tekniska fakulteten
-
visa färre...
-
(creator_code:org_t)
- Elsevier BV, 2023
- 2023
- Engelska.
-
Ingår i: Wear. - : Elsevier BV. - 0043-1648 .- 1873-2577. ; 524-525
- Relaterad länk:
-
http://dx.doi.org/10... (free)
-
visa fler...
-
https://liu.diva-por... (primary) (Raw object)
-
https://lup.lub.lu.s...
-
https://doi.org/10.1...
-
https://urn.kb.se/re...
-
visa färre...
Abstract
Ämnesord
Stäng
- The wear behavior of TiAlN coatings during turning of stainless steel 316L at low cutting speeds (60–120 m/min) was investigated using scanning electron microscopy. In this speed range, the coatings fail by fracture due to an adhesive wear mechanism. The fracture of the coating is described in detail, including the strong influence of Al-content and cutting speed on the rate of wear. Low Al-content (x ≤ 0.23) coatings showed worse wear resistance than high Al-content (x ≥ 0.53) samples. Less substrate is exposed when the cutting speed is increased, because of reduced adhesive wear. The TiN and Ti0.77Al0.23N coatings are severely worn for all cutting speeds while Ti0.47Al0.53N and Ti0.38Al0.62N remain essentially unaffected at the highest speed. The difference in wear behavior is interpreted as a difference in the fracture toughness of the coatings.
Ämnesord
- TEKNIK OCH TEKNOLOGIER -- Materialteknik -- Bearbetnings-, yt- och fogningsteknik (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Materials Engineering -- Manufacturing, Surface and Joining Technology (hsv//eng)
Nyckelord
- Adhesive wear
- Electron microscopy
- Fracture
- Low-speed turning operation
- Stainless steel 316L
- TiAlN
- TiAlN; Low-speed turning operation; Electron microscopy; Stainless steel 316L; Adhesive wear; Fracture
Publikations- och innehållstyp
- art (ämneskategori)
- ref (ämneskategori)
Hitta via bibliotek
-
Wear
(Sök värdpublikationen i LIBRIS)
Till lärosätets databas