SwePub
Sök i LIBRIS databas

  Utökad sökning

onr:"swepub:oai:lup.lub.lu.se:e45fd8da-2677-4ba7-aedb-b04190956160"
 

Sökning: onr:"swepub:oai:lup.lub.lu.se:e45fd8da-2677-4ba7-aedb-b04190956160" > Influence of anisot...

LIBRIS Formathandbok  (Information om MARC21)
FältnamnIndikatorerMetadata
00003339naa a2200289 4500
001oai:lup.lub.lu.se:e45fd8da-2677-4ba7-aedb-b04190956160
003SwePub
008160401s2014 | |||||||||||000 ||eng|
024a https://lup.lub.lu.se/record/47325872 URI
024a https://doi.org/10.1088/0965-0393/22/8/0850052 DOI
040 a (SwePub)lu
041 a engb eng
042 9 SwePub
072 7a art2 swepub-publicationtype
072 7a ref2 swepub-contenttype
100a Hallberg, Håkanu Lund University,Lunds universitet,Hållfasthetslära,Institutionen för byggvetenskaper,Institutioner vid LTH,Lunds Tekniska Högskola,Solid Mechanics,Department of Construction Sciences,Departments at LTH,Faculty of Engineering, LTH4 aut0 (Swepub:lu)soli-hha
2451 0a Influence of anisotropic grain boundary properties on the evolution of grain boundary character distribution during grain growth - a 2D level set study
264 c 2014-10-30
264 1b IOP Publishing,c 2014
520 a The present study elaborates on a 2D level set model of polycrystal microstructures that was recently established by adding the influence of anisotropic grain boundary energy and mobility on microstructure evolution. The new model is used to trace the evolution of grain boundary character distribution during grain growth. The employed level set formulation conveniently allows the grain boundary characteristics to be quantified in terms of coincidence site lattice (CSL) type per unit of grain boundary length, providing a measure of the distribution of such boundaries. In the model, both the mobility and energy of the grain boundaries are allowed to vary with misorientation. In addition, the influence of initial polycrystal texture is studied by comparing results obtained from a polycrystal with random initial texture against results from a polycrystal that initially has a cube texture. It is shown that the proposed level set formulation can readily incorporate anisotropic grain boundary properties and the simulation results further show that anisotropic grain boundary properties only have a minor influence on the evolution of CSL boundary distribution during grain growth. As anisotropic boundary properties are considered, the most prominent changes in the CSL distributions are an increase of general low-angle Σ1 boundaries as well as a more stable presence of Σ3 boundaries. The observations also hold for the case of an initially cube-textured polycrystal. The presence of this kind of texture has little influence over the evolution of the CSL distribution. Taking into consideration the anisotropy of grain boundary properties, grain growth alone does not seem to be sufficient to promote any significantly increased overall presence of CSL boundaries.
650 7a TEKNIK OCH TEKNOLOGIERx Maskinteknik0 (SwePub)2032 hsv//swe
650 7a ENGINEERING AND TECHNOLOGYx Mechanical Engineering0 (SwePub)2032 hsv//eng
710a Hållfasthetslärab Institutionen för byggvetenskaper4 org
773t Modelling and Simulation in Materials Science and Engineeringd : IOP Publishingg 22:8q 22:8x 0965-0393x 1361-651X
856u http://dx.doi.org/10.1088/0965-0393/22/8/085005x freey FULLTEXT
8564 8u https://lup.lub.lu.se/record/4732587
8564 8u https://doi.org/10.1088/0965-0393/22/8/085005

Hitta via bibliotek

Till lärosätets databas

Hitta mer i SwePub

Av författaren/redakt...
Hallberg, Håkan
Om ämnet
TEKNIK OCH TEKNOLOGIER
TEKNIK OCH TEKNO ...
och Maskinteknik
Artiklar i publikationen
Modelling and Si ...
Av lärosätet
Lunds universitet

Sök utanför SwePub

Kungliga biblioteket hanterar dina personuppgifter i enlighet med EU:s dataskyddsförordning (2018), GDPR. Läs mer om hur det funkar här.
Så här hanterar KB dina uppgifter vid användning av denna tjänst.

 
pil uppåt Stäng

Kopiera och spara länken för att återkomma till aktuell vy