| 1. |
- Chang, Abdul Sattar, et al.
(author)
-
Pd-Co3O4-based nanostructures for the development of enzyme-free glucose sensor
- 2022
-
In: Bulletin of Materials Science. - : INDIAN ACAD SCIENCES. - 0250-4707 .- 0973-7669. ; 45:2
-
Journal article (peer-reviewed)abstract
- In this study, we report enzyme-free glucose sensors based on palladium (Pd) nanoparticles deposited onto Co3O4 nanostructures. A simple, low-temperature aqueous method was used for the fabrication of Co3O4 nanostructures. Then, Pd nanoparticles were decorated onto Co3O4 nanostructures using the ultraviolet reduction method. Morphology, elemental composition and crystalline features of the proposed composite nanostructures were investigated by powder X-ray diffraction, scanning electron microscopy and energy dispersive spectroscopy techniques. Cyclic voltammetry and linear sweep voltammetry were used to investigate the electrochemical behaviour of Pd-Co3O4 nanostructures during glucose sensing. The proposed nanostructures showed excellent electrochemical activity for the quantitative detection of glucose at a potential of 0.6 V vs. Ag/AgCl. Importantly, the fabricated enzyme-free glucose sensor shows a linear response over the range of 1-6.0 mM glucose, with a limit of detection of 0.01 mM. The interference study was also carried out to probe the selectivity of Pd-Co3O4 nanostructures towards glucose detection in the presence of different interfering substances. The combined results attest that the as-synthesized Pd-Co3O4 nanostructures are highly stable and selective for the detection of glucose, suggesting their great potential for the quantitative determination of glucose in different biological fluids.
|
|
| 2. |
- Desai, R., et al.
(author)
-
Bulk magnetic properties of CdFe(2)O(4)in nano-regime
- 2007
-
In: Bulletin of Materials Science. - : Springer Science and Business Media LLC. - 0250-4707 .- 0973-7669. ; 30:3, s. 197-203
-
Journal article (peer-reviewed)abstract
- Cadmium ferrite particles have been synthesized using co-precipitation technique followed by a low temperature (600 degrees C) annealing in a time scale much shorter than reported in literature. Incorporation of sodium chloride during annealing helps to form a single phase spinel structure with a final particle size of around 50 nm. Even at such a short length scale we observe the overall magnetic properties to be similar to those of the bulk. The observed magnetic properties can be explained on the basis of an anti-ferromagnetic core with a shell containing 'ferromagnetic-like', but canted spin structure.
|
|
| 3. |
- Dissanayake, M. A. K. L., et al.
(author)
-
High-efficiency dye-sensitized solar cells fabricated with electrospun PVdF-HFP polymer nanofibre-based gel electrolytes
- 2023
-
In: Bulletin of Materials Science. - 0973-7669 .- 0250-4707. ; 46:2
-
Journal article (peer-reviewed)abstract
- Poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP) electrospun polymer nanofibre-based quasi-solid or gel electrolytes were successfully fabricated by incorporating a liquid electrolyte within the nanofibre membrane. The dye-sensitized solar cells (DSSCs) fabricated with gel and with liquid electrolyte were characterized by photocurrent–voltage measurements and electrochemical impedance spectroscopy measurements. The maximum efficiency (η) of 6.79% was observed for the DSSC fabricated with optimized nanofibre membrane thickness, corresponding to 4 min of electrospinning time. The optimized PVdF-HFP nanofibre gel electrolyte shows an ionic conductivity of 7.16 × 10−3 S cm–1 at 25°C, while the corresponding liquid electrolyte exhibits an ionic conductivity of 11.69 × 10–3 S cm–1 at the same temperature. The open circuit voltage (Voc), short circuit current density (Jsc) and fill factor were recorded as 801.40 mV, 12.70 mA cm–2, and 66.67%, respectively, at an incident light intensity of 100 mW cm–2 with a 1.5 AM filter. The nanofibre gel electrolyte-based cell showed an efficiency of 6.79%, whereas the efficiency of the conventional liquid electrolyte-based cell was 7.28% under the same conditions. Furthermore, nanofibre gel electrolyte-based cells exhibited better stability, maintaining 85.40% of initial efficiency after 120 h. These results show that the optimized, polymer nanofibre-based gel electrolyte can be used successfully to replace the liquid electrolyte in DSSCs without much loss of efficiency but improving the stability while minimizing most of the drawbacks associated with liquid electrolytes.
|
|
| 4. |
- Kanungo, J, et al.
(author)
-
XPS study of palladium sensitized nano porous silicon thin film
- 2010
-
In: BULLETIN OF MATERIALS SCIENCE. - : Indian Academy of Sciences; 1999 / Indian Academy of Sciences, Springer. - 0250-4707 .- 0973-7669. ; 33:6, s. 647-651
-
Journal article (peer-reviewed)abstract
- Nano porous silicon (PS) was formed on p-type monocrystalline silicon of 2-5 Omega cm resistivity and (100) orientation by electrochemical anodization method using HF and ethanol as the electrolytes. High density of surface states, arising due to its nano structure, is responsible for the uncontrolled oxidation in air and for the deterioration of the PS surface with time. To stabilize the material PS surface was modified by a simple and low cost chemical method using PdCl2 solution at room temperature. X-ray photoelectron spectroscopy (XPS) was performed to reveal the chemical composition and the relative concentration of palladium on the nanoporous silicon thin films. An increase of SiO2 formation was observed after PdCl2 treatment and presence of palladium was also detected on the modified surface. I-V characteristics of Al/PS junction were studied using two lateral Al contacts and a linear relationship was obtained for Pd modified PS surface. Stability of the contact was studied for a time period of around 30 days and no significant ageing effect could be observed.
|
|
