| 1. |
- Henriksson, Ida, 1990, et al.
(author)
-
Increased lipid accumulation and adipogenic gene expression of adipocytes in 3D bioprinted nanocellulose scaffolds
- 2017
-
In: Biofabrication. - : IOP Publishing. - 1758-5082 .- 1758-5090. ; 9:1, s. Article Number: 015022 -
-
Journal article (peer-reviewed)abstract
- Compared to standard 2D culture systems, new methods for 3D cell culture of adipocytes could provide more physiologically accurate data and a deeper understanding of metabolic diseases such as diabetes. By resuspending living cells in a bioink of nanocellulose and hyaluronic acid, we were able to print 3D scaffolds with uniform cell distribution. After one week in culture, cell viability was 95%, and after two weeks the cells displayed a more mature phenotype with larger lipid droplets than standard 2D cultured cells. Unlike cells in 2D culture, the 3D bioprinted cells did not detach upon lipid accumulation. After two weeks, the gene expression of the adipogenic marker genes PPAR. and FABP4 was increased 2.0- and 2.2-fold, respectively, for cells in 3D bioprinted constructs compared with 2D cultured cells. Our 3D bioprinted culture system produces better adipogenic differentiation of mesenchymal stem cells and a more mature cell phenotype than conventional
|
|
| 2. |
- Aronsson, Christopher, et al.
(author)
-
Dynamic peptide-folding mediated biofunctionalization and modulation of hydrogels for 4D bioprinting
- 2020
-
In: Biofabrication. - : Institute of Physics Publishing (IOPP). - 1758-5082 .- 1758-5090. ; 12:3
-
Journal article (peer-reviewed)abstract
- Hydrogels are used in a wide range of biomedical applications, including three-dimensional (3D) cell culture, cell therapy and bioprinting. To enable processing using advanced additive fabrication techniques and to mimic the dynamic nature of the extracellular matrix (ECM), the properties of the hydrogels must be possible to tailor and change over time with high precision. The design of hydrogels that are both structurally and functionally dynamic, while providing necessary mechanical support is challenging using conventional synthesis techniques. Here, we show a modular and 3D printable hydrogel system that combines a robust but tunable covalent bioorthogonal cross-linking strategy with specific peptide-folding mediated interactions for dynamic modulation of cross-linking and functionalization. The hyaluronan-based hydrogels were covalently cross-linked by strain-promoted alkyne-azide cycloaddition using multi-arm poly(ethylene glycol). In addition, a de novo designed helix-loop-helix peptide was conjugated to the hyaluronan backbone to enable specific peptide-folding modulation of cross-linking density and kinetics, and hydrogel functionality. An array of complementary peptides with different functionalities was developed and used as a toolbox for supramolecular tuning of cell-hydrogel interactions and for controlling enzyme-mediated biomineralization processes. The modular peptide system enabled dynamic modifications of the properties of 3D printed structures, demonstrating a novel route for design of more sophisticated bioinks for four-dimensional bioprinting. © 2020 The Author(s). Published by IOP Publishing Ltd.
|
|
| 3. |
- Christoffersson, Jonas, et al.
(author)
-
Developing organ-on-a-chip concepts using bio-mechatronic design methodology
- 2017
-
In: Biofabrication. - : IOP PUBLISHING LTD. - 1758-5082 .- 1758-5090. ; 9:2
-
Journal article (peer-reviewed)abstract
- Mechatronic design is an engineering methodology for conceiving, configuring and optimising the design of a technical device or product to the needs and requirements of the final user. In this article, we show how the basic principles of this methodology can be exploited for in vitro cell cultures-often referred to as organ-on-a-chip devices. Due to the key role of the biological cells, we have introduced the term bio-mechatronic design, to highlight the complexity of designing a system that should integrate biology, mechanics and electronics in the same device structure. The strength of the mechatronic design is to match the needs of the potential users to a systematic evaluation of overall functional design alternative. It may be especially attractive for organs-on-chips where biological constituents such as cells and tissues in 3D settings and in a fluidic environment should be compared, screened and selected. Through this approach, design solutions ranked to customer needs are generated according to specified criteria, thereby defining the key constraints of the fabrication. As an example, the bio-mechatronic methodology is applied to a liver-on-a-chip based on information extrapolated from previous theoretical and experimental knowledge. It is concluded that the methodology can generate new fabrication solutions for devices, as well as efficient guidelines for refining the design and fabrication of many of todays organ-on-a-chip devices.
|
|
| 4. |
- Christoffersson, Jonas, 1986-, et al.
(author)
-
Fabrication of modular hyaluronan-PEG hydrogels to support 3D cultures of hepatocytes in a perfused liver-on-a-chip device
- 2019
-
In: Biofabrication. - : Institute of Physics (IOP). - 1758-5082 .- 1758-5090. ; 11:1, s. 1-13
-
Journal article (peer-reviewed)abstract
- Liver cell culture models are attractive in both tissue engineering and for development of assays for drug toxicology research. To retain liver specific cell functions, the use of adequate cell types and culture conditions, such as a 3D orientation of the cells and a proper supply of nutrients and oxygen, are critical. In this article, we show how extracellular matrix mimetic hydrogels can support hepatocyte viability and functionality in a perfused liver-on-a-chip device. A modular hydrogel system based on hyaluronan and poly(ethylene glycol) (HA-PEG), modified with cyclooctyne moieties for bioorthogonal strain-promoted alkyne-azide 1, 3-dipolar cycloaddition (SPAAC), was developed, characterized, and compared for cell compatibility to hydrogels based on agarose and alginate. Hepatoma cells (HepG2) formed spheroids with viable cells in all hydrogels with the highest expression of albumin and urea in alginate hydrogels. By including an excess of cyclooctyne in the HA backbone, azide-modified cell adhesion motifs (linear and cyclic RGD peptides) could be introduced in order to enhance viability and functionality of human induced pluripotent stem cell derived hepatocytes (hiPS-HEPs). In the HA-PEG hydrogels modified with cyclic RGD peptides hiPS-HEPs migrated and grew in 3D and showed an increased viability and higher albumin production compared to when cultured in the other hydrogels. This flexible SPAAC crosslinked hydrogel system enabled fabrication of perfused 3D cell culture of hiPS-HEPs and is a promising material for further development and optimization of liver-on-a-chip devices.
|
|
| 5. |
- Göhl, Johan, 1989, et al.
(author)
-
Simulations of 3D bioprinting : Predicting bioprintability of nanofibrillar inks
- 2018
-
In: Biofabrication. - : IOP Publishing. - 1758-5082 .- 1758-5090. ; 10:3
-
Journal article (peer-reviewed)abstract
- 3D bioprinting with cell containing bioinks show great promise in the biofabrication of patient specific tissue constructs. To fulfil the multiple requirements of a bioink, a wide range of materials and bioink composition are being developed and evaluated with regard to cell viability, mechanical performance and printability. It is essential that the printability and printing fidelity is not neglected since failure in printing the targeted architecture may be catastrophic for the survival of the cells and consequently the function of the printed tissue. However, experimental evaluation of bioinks printability is time-consuming and must be kept at a minimum, especially when 3D bioprinting with cells that are valuable and costly. This paper demonstrates how experimental evaluation could be complemented with computer based simulations to evaluate newly developed bioinks. Here, a computational fluid dynamics simulation tool was used to study the influence of different printing parameters and evaluate the predictability of the printing process. Based on data from oscillation frequency measurements of the evaluated bioinks, a full stress rheology model was used, where the viscoelastic behaviour of the material was captured. Simulation of the 3D bioprinting process is a powerful tool and will help in reducing the time and cost in the development and evaluation of bioinks. Moreover, it gives the opportunity to isolate parameters such as printing speed, nozzle height, flow rate and printing path to study their influence on the printing fidelity and the viscoelastic stresses within the bioink. The ability to study these features more extensively by simulating the printing process will result in a better understanding of what influences the viability of cells in 3D bioprinted tissue constructs.
|
|
| 6. |
- Nguyen, Dao Thi Thuy, et al.
(author)
-
Endocrine system on chip for a diabetes treatment model
- 2017
-
In: Biofabrication. - : IOP PUBLISHING LTD. - 1758-5082 .- 1758-5090. ; 9:1
-
Journal article (peer-reviewed)abstract
- The endocrine system is a collection of glands producing hormones which, among others, regulates metabolism, growth and development. One important group of endocrine diseases is diabetes, which is caused by a deficiency or diminished effectiveness of endogenous insulin. By using a microfluidic perfused 3D cell-culture chip, we developed an endocrine system on chip to potentially be able to screen drugs for the treatment of diabetes by measuring insulin release over time. Insulin-secreting beta-cells are located in the pancreas, while L-cells, located in the small intestines, stimulate insulin secretion. Thus, we constructed a co-culture of intestinal-pancreatic cells to measure the effect of glucose on the production of glucagon-like peptide-1 (GLP-1) from the L-cell line (GLUTag) and insulin from the pancreatic beta-cell line (INS-1). After three days of culture, both cell lines formed aggregates, exhibited 3D cell morphology, and showed good viability (amp;gt; 95%). We separately measured the dynamic profile of GLP-1 and insulin release at glucose concentrations of 0.5 and 20 mM, as well as the combined effect of GLP-1 on insulin production at these glucose concentrations. In response to glucose stimuli, GLUTag and INS-1 cells produced higher amounts of GLP-1 and insulin, respectively, compared to a static 2D cell culture. INS-1 combined with GLUTag cells exhibited an even higher insulin production in response to glucose stimulation. At higher glucose concentrations, the diabetes model on chip showed faster saturation of the insulin level. Our results suggest that the endocrine system developed in this study is a useful tool for observing dynamical changes in endocrine hormones (GLP-1 and insulin) in a glucose-dependent environment. Moreover, it can potentially be used to screen GLP-1 analogues and natural insulin and GLP-1 stimulants for diabetes treatment.
|
|
| 7. |
- Ojansivu, Miina, et al.
(author)
-
Wood-based nanocellulose and bioactive glass modified gelatin-alginate bioinks for 3D bioprinting of bone cells
- 2019
-
In: Biofabrication. - : Institute of Physics Publishing (IOPP). - 1758-5082 .- 1758-5090. ; 11:3
-
Journal article (peer-reviewed)abstract
- A challenge in the extrusion-based bioprinting is to find a bioink with optimal biological and physicochemical properties. The aim of this study was to evaluate the influence of wood-based cellulose nanofibrils (CNF) and bioactive glass (BaG) on the rheological properties of gelatin-alginate bioinks and the initial responses ofbone cells embedded in these inks. CNF modulated the flow behavior of the hydrogels, thus improving their printability. Chemical characterization by SEM-EDX and ion release analysis confirmed the reactivity of the BaG in the hydrogels. The cytocompatibility of the hydrogels was shown to be good, as evidenced by the viability of human osteoblast-like cells (Saos-2) in cast hydrogels. For bioprinting, 4-layer structures were printed from cell-containing gels and crosslinked with CaCl2. Viability, proliferation and alkaline phosphatase activity (ALP) were monitored over 14 d. In the BaG-free gels, Saos-2 cells remained viable, but in the presence of BaG the viability and proliferation decreased in correlation with the increased viscosity. Still, there was a constant increase in the ALP activity in all the hydrogels. Further bioprinting experiments were conducted using human bone marrow-derived mesenchymal stem cells (hBMSCs), a clinically relevant cell type. Interestingly, hBMSCs tolerated the printing process better than Saos-2 cells and the ALP indicated BaG-stimulated early osteogenic commitment. The addition of CNF and BaG to gelatin-alginate bioinks holds great potential for bone tissue engineering applications.
|
|
| 8. |
- Rasti Boroojeni, Fatemeh, et al.
(author)
-
Proteolytic remodeling of 3D bioprinted tumor microenvironments
- 2024
-
In: Biofabrication. - : IOP Publishing Ltd. - 1758-5082 .- 1758-5090. ; 16:2
-
Journal article (peer-reviewed)abstract
- In native tissue, remodeling of the pericellular space is essential for cellular activities and is mediated by tightly regulated proteases. Protease activity is dysregulated in many diseases, including many forms of cancer. Increased proteolytic activity is directly linked to tumor invasion into stroma, metastasis, and angiogenesis as well as all other hallmarks of cancer. Here we show a strategy for 3D bioprinting of breast cancer models using well-defined protease degradable hydrogels that can facilitate exploration of the multifaceted roles of proteolytic extracellular matrix remodeling in tumor progression. We designed a set of bicyclo[6.1.0]nonyne functionalized hyaluronan (HA)-based bioinks cross-linked by azide-modified poly(ethylene glycol) (PEG) or matrix metalloproteinase (MMP) degradable azide-functionalized peptides. Bioprinted structures combining PEG and peptide-based hydrogels were proteolytically degraded with spatial selectivity, leaving non-degradable features intact. Bioprinting of tumor-mimicking microenvironments using bioinks comprising human breast cancer cells (MCF-7) and fibroblast in hydrogels with different susceptibilities to proteolytic degradation shows that MCF-7 proliferation and spheroid size were significantly increased in protease degradable hydrogel compartments, but only in the presence of fibroblasts. In the absence of fibroblasts in the stromal compartment, cancer cell proliferation was reduced and did not differ between degradable and nondegradable hydrogels. The interactions between spatially separated fibroblasts and MCF-7 cells consequently resulted in protease-mediated remodeling of the bioprinted structures and a significant increase in cancer cell spheroid size, highlighting the close interplay between cancer cells and stromal cells in the tumor microenvironment and the influence of proteases in tumor progression.
|
|
| 9. |
- Sämfors, Sanna, 1987, et al.
(author)
-
Biofabrication of bacterial nanocellulose scaffolds with complex vascular structure
- 2019
-
In: Biofabrication. - : IOP Publishing. - 1758-5082 .- 1758-5090. ; 11:4
-
Journal article (peer-reviewed)abstract
- Bacterial nanocellulose (BNC) has proven to be an effective hydrogel-like material for different tissue engineering applications due to its biocompatibility and good mechanical properties. However, as for all biomaterials, in vitro biosynthesis of large tissue constructs remains challenging due to insufficient oxygen and nutrient transport in engineered scaffold-cell matrices. In this study we designed, biofabricated and evaluated bacterial nanocellulose scaffolds with a complex vascular mimetic lumen structure. As a first step a method for creating straight channeled structures within a bacterial nanocellulose scaffold was developed and evaluated by culturing of Human Umbilical Vein Endothelial Cells (HUVECs). In a second step, more complex structures within the scaffolds were produced utilizing a 3D printer. A print mimicking a vascular tree acted as a sacrificial template to produce a network within the nanoporous bacterial nanocellulose scaffolds that could be lined with endothelial cells. In a last step, a method to produce large constructs with interconnected macro porosity and vascular like lumen structure was developed. In this process patient data from x-ray computed tomography scans was used to create a mold for casting a full-sized kidney construct. By showing that the 3D printing technology can be combined with BNC biosynthesis we hope to widen the opportunities of 3D printing, while also enabling the production of BNC scaffolds constructs with tailored vascular architectures and properties.
|
|
| 10. |
- Zhang, Jianhua, et al.
(author)
-
Long-term mechanical loading is required for the formation of 3D bioprinted functional osteocyte bone organoids
- 2022
-
In: Biofabrication. - : IOP Publishing. - 1758-5082 .- 1758-5090. ; 14
-
Journal article (peer-reviewed)abstract
- Mechanical loading has been shown to influence various osteogenic responses of bone-derived cells and bone formation in vivo. However, the influence of mechanical stimulation on the formation of bone organoid in vitro is not clearly understood. Here, three-dimensional (3D) bioprinted human mesenchymal stem cells-laden graphene oxide composite scaffolds were cultured in a novel cyclic-loading bioreactors for up to 56 d. Our results showed that mechanical loading from day 1 (ML01) significantly increased organoid mineral density, organoid stiffness, and osteoblast differentiation compared with non-loading and mechanical loading from day 21. Importantly, ML01 stimulated collagen I maturation, osteocyte differentiation, lacunar-canalicular network formation and YAP expression on day 56. These finding are the first to reveal that long-term mechanical loading is required for the formation of 3D bioprinted functional osteocyte bone organoids. Such 3D bone organoids may serve as a human-specific alternative to animal testing for the study of bone pathophysiology and drug screening.
|
|
