1. |
|
|
2. |
- Alimohammadzadeh, Rana, et al.
(author)
-
Scalable Improvement of the Strength Properties of Chemimechanical Pulp Fibers by Eco-Friendly Catalysis
- 2018
-
In: IMPC 2018. - Trondheim, Norway.
-
Conference paper (peer-reviewed)abstract
- The sustainable improvement of the strength properties of chemimechanical pulp by eco-friendlycatalysis is disclosed. Significant research activities have been performed on the use of cationic starchand polyelectrolyte complexes for improving the strength properties of cellulose-based materials. Herewe apply an eco-friendly strategy based on catalysis for significantly improving the strength propertiesof sheets made from chemimechanical pulp (CTMP) and bleeched sulphite pulp (BSP) using sustainablepolyelectrolyte complexes as the strength additives and organocatalysis. This surface engineeringstrategy significantly increased the strength properties of the assembled sheets (up to 100% in the caseof Z-strength). We also developed a catalytic selective colour marking of the cationic potato starch (CS)and carboxymethylcellulose (CMC) in order to elucidated how the specific strength additives aredistributed on the sheets. It revealed that the strength additives were more evenly distributed on thesheets made from CTMP as compared to BSP sheets. This is most likely attributed to the presence oflignin in the former lignocellulosic material. It also contributes to the increase in strength (up to 100%,Z-strength) for the CTMP derived sheets. The selective colour marking method also revealed that morestrength additives had been bound to the pulps in the presence of the catalyst.
|
|
3. |
- Alimohammadzadeh, Rana, et al.
(author)
-
Sustainable Surface Engineering of Lignocellulose and Cellulose by Synergistic Combination of Metal‐Free Catalysis and Polyelectrolyte Complexes
- 2019
-
In: Global Challenges. - : Wiley. - 2056-6646. ; 3
-
Journal article (peer-reviewed)abstract
- A sustainable strategy for synergistic surface engineering of lignocellulose and cellulose fibers derived from wood by synergistic combination of metal‐free catalysis and renewable polyelectrolyte (PE) complexes is disclosed. The strategy allows for improvement and introduction of important properties such as strength, water resistance, and fluorescence to the renewable fibers and cellulosic materials. For example, the “green” surface engineering significantly increases the strength properties (up to 100% in Z‐strength) of chemi‐thermomechanical pulp (CTMP) and bleached sulphite pulp (BSP)‐derived sheets. Next, performing an organocatalytic silylation with a nontoxic organic acid makes the corresponding lignocellulose and cellulose sheets hydrophobic. A selective color modification of polysaccharides is developed by combining metal‐free catalysis and thiol‐ene click chemistry. Next, fluorescent PE complexes based on cationic starch (CS) and carboxymethylcellulose (CMC) are prepared and used for modification of CTMP or BSP in the presence of a metal‐free catalyst. Laser‐scanning confocal microscopy reveals that the PE‐strength additive is evenly distributed on the CTMP and heterogeneously on the BSP. The fluorescent CS distribution on the CTMP follows the lignin distribution of the lignocellulosic fibers.
|
|
4. |
- Andres, Britta, 1986-, et al.
(author)
-
Cellulose binders for electric double-layer capacitor electrodes : The influence of cellulose quality on electrical properties
- 2018
-
In: Materials & design. - : Elsevier BV. - 0264-1275 .- 1873-4197. ; 141, s. 342-349
-
Journal article (peer-reviewed)abstract
- Cellulose derivatives are widely used as binders and dispersing agents in different applications. Binders composed of cellulose are an environmentally friendly alternative to oil-based polymer binding agents. Previously, we reported the use of cellulose nanofibers (CNFs) as binders in electrodes for electric double-layer capacitors (EDLCs). In addition to good mechanical stability, we demonstrated that CNFs enhanced the electrical performance of the electrodes. However, cellulose fibers can cover a broad range of length scales, and the quality requirements from an electrode perspective have not been thoroughly investigated. To evaluate the influence of fiber quality on electrode properties, we tested seven samples with different fiber dimensions that are based on the same kraft pulp. To capture the length scale from fibers to nanofibrils, we evaluated the performance of the untreated kraft pulp, refined fibers, microfibrillated cellulose (MFC) and CNFs. Electrodes with kraft pulp or refined fibers showed the lowest electrical resistivity. The specific capacitances of all EDLCs were surprisingly similar, but slightly lower for the EDLC with CNFs. The same electrode sample with CNFs also showed a slightly higher equivalent series resistance (ESR), compared to those of the other EDLCs. Graphite dispersions with MFC showed the best dispersion stability.
|
|
5. |
- Andres, Britta, 1986-
(author)
-
Low-Cost, Environmentally Friendly Electric Double-Layer Capacitors : Concept, Materials and Production
- 2017
-
Doctoral thesis (other academic/artistic)abstract
- Today’s society is currently performing an exit from fossilfuel energy sources. The change to sustainable alternativesrequires inexpensive and environmentally friendly energy storagedevices. However, most current devices contain expensive,rare or toxic materials. These materials must be replaced bylow-cost, abundant, nontoxic components.In this thesis, I suggest the production of paper-based electricdouble-layer capacitors (EDLCs) to meet the demand oflow-cost energy storage devices that provide high power density.To fulfill the requirements of sustainable and environmentallyfriendly devices, production of EDLCs that consist of paper,graphite and saltwater is proposed. Paper can be used as aseparator between the electrodes and as a substrate for theelectrodes. Graphite is suited for use as an active material in theelectrodes, and saltwater can be employed as an electrolyte.Westudied and developed different methods for the productionof nanographite and graphene from graphite. Composites containingthese materials and similar advanced carbon materialshave been tested as electrode materials in EDLCs. I suggest theuse of cellulose nanofibers (CNFs) or microfibrillated cellulose(MFC) as a binder in the electrodes. In addition to improvedmechanical stability, the nanocellulose improved the stabilityof graphite dispersions and the electrical performance of theelectrodes. The influence of the cellulose quality on the electricalproperties of the electrodes and EDLCs was investigated.The results showed that the finest nanocellulose quality is notthe best choice for EDLC electrodes; MFC is recommended forthis application instead. The results also demonstrated thatthe capacitance of EDLCs can be increased if the electrodemasses are adjusted according to the size of the electrolyte ions.Moreover, we investigated the issue of high contact resistancesat the interface between porous carbon electrodes and metalcurrent collectors. To reduce the contact resistance, graphitefoil can be used as a current collector instead of metal foils.Using the suggested low-cost materials, production methodsand conceptual improvements, it is possible to reduce the material costs by more than 90% in comparison with commercialunits. This confirms that paper-based EDLCs are apromising alternative to conventional EDLCs. Our findings andadditional research can be expected to substantially supportthe design and commercialization of sustainable EDLCs andother green energy technologies.
|
|
6. |
- Blomquist, Nicklas, 1987-, et al.
(author)
-
Effects of Geometry on Large-scale Tube-shear Exfoliation of Multilayer Graphene and Nanographite in Water
- 2019
-
In: Scientific Reports. - : Springer Science and Business Media LLC. - 2045-2322. ; 9:1
-
Journal article (peer-reviewed)abstract
- Industrially scalable methods for the production of graphene and other nanographites are needed to achieve cost-efficient commercial products. At present, there are several available routes for the production of these materials but few allow large-scale manufacturing and environmentally friendly low-cost solvents are rarely used. We have previously demonstrated a scalable and low-cost industrial route to produce nanographites by tube-shearing in water suspensions. However, for a deeper understanding of the exfoliation mechanism, how and where the actual exfoliation occurs must be known. This study investigates the effect of shear zone geometry, straight and helical coil tubes, on this system based on both numerical simulation and experimental data. The results show that the helical coil tube achieves a more efficient exfoliation with smaller and thinner flakes than the straight version. Furthermore, only the local wall shear stress in the turbulent flow is sufficient for exfoliation since the laminar flow contribution is well below the needed range, indicating that exfoliation occurs at the tube walls. This explains the exfoliation mechanism of water-based tube-shear exfoliation, which is needed to achieve scaling to industrial levels of few-layer graphene with known and consequent quality.
|
|
7. |
- Blomquist, Nicklas, 1987-, et al.
(author)
-
Influence of Substrate in Roll-to-roll Coated Nanographite Electrodes for Metal-free Supercapacitors
- 2020
-
In: Scientific Reports. - : Springer Science and Business Media LLC. - 2045-2322. ; 10:1
-
Journal article (peer-reviewed)abstract
- Due to the high electric conductivity and large surface area of nanographites, such as graphene and graphite nanoplatlets, these materials have gained a large interest for use in energy storage devices. However, due to the thin flake geometry, the viscosity of aqueous suspensions containing these materials is high even at low solids contents. This together with the use of high viscosity bio-based binders makes it challenging to coat in a roll-to-roll process with sufficient coating thickness. Electrode materials for commercial energy storage devices are often suspended by organic solvents at high solids contents and coated onto metal foils used as current-collectors. Another interesting approach is to coat the electrode onto the separator, to enable large-scale production of flat cell stacks. Here, we demonstrate an alternative, water-based approach that utilize slot-die coating to coat aqueous nanographite suspension with nanocellulose binder onto the paper separator, and onto the current collector as reference, in aqueous metal-free supercapacitors. The results show that the difference in device equivalent series resistance (ESR) due to interfacial resistance between electrode and current collector was much lower than expected and thus similar or lower compared to other studies with a aqueous supercapacitors. This indicates that electrode coated paper separator substrates could be a promising approach and a possible route for manufacturing of low-cost, environmentally friendly and metal-free energy storage devices.
|
|
8. |
|
|
9. |
- Blomquist, Nicklas, 1987-
(author)
-
Large-Scale Graphene Production for Environmentally Friendly and Low-Cost Energy Storage : Production, Coating, and Applications
- 2019
-
Doctoral thesis (other academic/artistic)abstract
- There is great demand for energy-efficient, environmentally sustainable, and cost-effective electrical energy storage devices. One important aspect of this demand is the need for automotive electrification to achieve more energy-efficient transportation at a reasonable cost, thus supporting a fossil-fuel free society. Another important aspect is the requirement for energy storage in the growing field of renewable energy production from wind and solar sources, which generates an irregular supply of electricity due to weather conditions.Much of the research in this area has been conducted in the field of battery technology with impressive results, but the need for rapid storage devices such as supercapacitors is growing. Due to the excellent ability of supercapacitors to handle short peak power pulses with high efficiency along with their long lifetime and superior cyclability, their implementations range from small consumer electronics to electric vehicles and stationary grid applications. Supercapacitors also have the potential to complement batteries to improve pulse efficiency and lifetime of the system, however, the cost of supercapacitors is a significant issue for large-scale commercial use, leading to a demand for sustainable, low-cost materials and simplified manufacturing processes. An important way to address this need is to develop a cost-efficient and environment-friendly large-scale process to produce highly conductive nanographites, such as graphene and graphite nanoplatelets, along with methods to manufacture low-cost electrodes from large area coating.In this thesis, I present a novel process to mechanically exfoliate industrial quantities of nanographite from graphite in an aqueous environment with low energy consumption and at controlled shear conditions. The process is based on hydrodynamic tube-shearing and can produce both multilayer graphene and nanometer-thick and micrometer-wide flakes of nanographite. I also describe the production of highly conductive and robust carbon composites based on the addition of nanocellulose during production; these are suitable as electrodes in applications ranging from supercapacitors and batteries to printed electronics and solar cells.Furthermore I demonstrate a scalable route for roll-to-roll coating of the nanographite-nanocellulose electrode material and propose a novel aqueous, low-cost, and metal-free supercapacitor concept with graphite foil functioning as the current collector. The supercapacitors possessedmore than half the specific capacitance of commercial units but achieved a material cost reduction of more than 90 %, demonstrating anenvironment-friendly, low-cost alternative to conventional supercapacitors.
|
|
10. |
- Dahlström, Christina, 1977-, et al.
(author)
-
Base Sheet Structures that Control Coating Uniformity: Effects of Length Scale
- 2008
-
In: TAPPI Advanced Coating Fundamentals Symposium Proceedings. - : TAPPI Press. - 1595101748 - 9781595101747 ; , s. 124-133
-
Conference paper (peer-reviewed)abstract
- Characterization of the base sheet properties and coating layer properties was performed by using scanning electron microscope (SEM) images of paper cross-sections and image analysis. Frequency analysis was used to study how the base sheet properties affect coating thickness uniformity at different length scales. Samples analysed were Lightweight Coated (LWC) base sheets blade-coated on only one side with coat weights of 12 and 22 g/m2. A number of images were taken in sequence giving a total length of more than 6 mm. The results showed that the surface height variations of the base sheet control coating uniformity in the entire examined length scale, but with different mechanisms. At short wavelengths the coating mechanism was “level coating” where the coating suspension fills small pores (“levels”), whereas at longer wavelengths the coating suspension follows the surface profile and “contour coating” becomes more prevalent. In other words, the level- and contour-coatings represent the coating mechanisms in different length scales. Surface height variations can be explained by base sheet thickness only at short wavelengths, but at all other wavelengths the surface height variations were very much independent of the base sheet structure properties measured.
|
|