1. |
- Abolhasani, Hasanali, et al.
(author)
-
Development of self-healable acrylic water-based environmental-friendly coating as an alternative to chromates coatings
- 2023
-
In: Progress in organic coatings. - : Elsevier B.V.. - 0300-9440 .- 1873-331X. ; 176
-
Journal article (peer-reviewed)abstract
- In this study, different coating systems, including solvent-based epoxy and water-based acrylic resins, were evaluated for their potential as an alternative to chromate coatings in order to avoid Cr(VI) toxic hazards. The resins were used as either pigment-free coatings or were formulated with 20-wt% zinc/aluminum pigments. The coatings were subsequently applied on galvanized ST12 steel plates and their corrosion resistance was investigated by electrochemical impedance spectroscopy (EIS) evaluations. The effect of the binder and pigment type on the impact resistance of two different polymeric coatings was also evaluated. The results of impact tests revealed completely peeled film from the substrate for epoxy coatings. However, under the same experimental conditions, very few small cracks were created in water-based acrylic coatings for both pigmented and pigment-free cases. In addition, some other parameters such as drying time and coating cost were taken into account to select a good alternative to chromate coatings. The results of this work can facilitate the introduction of an inexpensive environmentally friendly acrylic coating as a promising self-healing alternative to chromate coating.
|
|
2. |
- Alagumalai, Vasudevan, et al.
(author)
-
Impact response and damage tolerance of hybrid glass/kevlar-fibre epoxy structural composites
- 2021
-
In: Polymers. - : MDPI. - 2073-4360. ; 13:16
-
Journal article (peer-reviewed)abstract
- The present study is aimed at investigating the effect of hybridisation on Kevlar/E-Glass based epoxy composite laminate structures. Composites with 4 mm thickness and 16 layers of fibre (14 layers of E-glass centred and 2 outer layers of Kevlar) were fabricated using compression moulding technique. The fibre orientation of the Kevlar layers had 3 variations (0, 45 and 60°), whereas the E-glass fibre layers were maintained at 0° orientation. Tensile, flexural, impact (Charpy and Izod), interlaminar shear strength and ballistic impact tests were conducted. The ballistic test was performed using a gas gun with spherical hard body projectiles at the projectile velocity of 170 m/s. The pre-and post-impact velocities of the projectiles were measured using a high-speed camera. The energy absorbed by the composite laminates was further reported during the ballistic test, and a computerised tomographic scan was used to analyse the impact damage. The composites with 45° fibre orientation of Kevlar fibres showed better tensile strength, flexural strength, Charpy impact strength, and energy absorption. The energy absorbed by the composites with 45° fibre orientation was 58.68 J, which was 14% and 22% higher than the 0° and 60° oriented composites. © 2021 by the authors. Licensee MDPI, Basel, Switzerland.
|
|
3. |
- Aminoroaya, Alireza, et al.
(author)
-
A Review of Dental Composites : Methods Of Characterizations
- 2020
-
In: ACS Biomaterials Science & Engineering. - : American Chemical Society (ACS). - 2373-9878. ; 6:7, s. 3713-3744
-
Research review (peer-reviewed)abstract
- Dental composites are becoming increasingly popular in esthetic restorative dentistry and present a promising substitute for amalgam. However, the major hurdles that hinder their total adoption in restorative dentistry are limited longevity and possible health risks, leading to significant attempts for addressing these shortcomings. Besides the new materials, the evaluation methods play a critical role in the introduction and improvement of these types of materials. This review aims to cover the characterization methods in the evaluation of dental composites that are most employed nowadays. Therefore, the methods for evaluating the physical properties of the dental composites are first explained. Subsequently, the assessment methods of curing kinetics and the mechanical properties of the composites are classified and reviewed. Afterward, the article delves into the introduction and classification of the microscopic and antibacterial evaluation methods. Finally, the test methods for assessment of in vitro cytotoxicity and self-healing ability are described. It should be noted, for each test method, the most recent and interesting articles are cited. It is envisaged that this review will facilitate an understanding and provide knowledge for the section and utilizing the most effective and suitable characterization methods for future research on the development of dental composites.
|
|
4. |
- Aminoroaya, Alireza, et al.
(author)
-
A review of dental composites : Challenges, chemistry aspects, filler influences, and future insights
- 2021
-
In: Composites Part B. - : Elsevier. - 1359-8368 .- 1879-1069. ; 216
-
Research review (peer-reviewed)abstract
- Resin-based dental composites are promising tooth-resembling materials in restorative dentistry. The limited longevity of dental composite restorations due to the bulk/marginal fracture and secondary caries as well as possible health risks are the critical challenges faced by such materials. Therefore, developments of resin-based dental composites received considerable attention in academic researches for clinical applications. A comprehensive review of the recent developments in the scientific literature on resin-based dental composites is presented in this article. Firstly, in the article, the challenges in dental composites are introduced and then the chemical aspects of the systems are classified through a review of employed resins. Subsequently, the different characteristics related to the fillers employed for the development of the resin-based dental composites are described. Finally, conclusions are drawn and future insights are proposed. This article provides an insight that paves the way for tailoring and designing resin-based dental composites for clinical applications.
|
|
5. |
- Aminoroaya, Alireza, et al.
(author)
-
Facile encapsulation of cyanoacrylate-based bioadhesive by electrospray method and investigation of the process parameters
- 2024
-
In: Scientific Reports. - : Nature Research. - 2045-2322. ; 14:1
-
Journal article (peer-reviewed)abstract
- Polymer microcapsules containing cyanoacrylates have represented a promising option to develop self-healing biomaterials. This study aims to develop an electrospray method for the preparation of capsules using poly(methyl methacrylate) (PMMA) as the encapsulant and ethyl 2-cyanoacrylate (EC) as the encapsulate. It also aims to study the effect of the electrospray process parameters on the size and morphology of the capsules. The capsules were characterized using Fourier-transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), and field-emission scanning electron microscopy (FE-SEM). Moreover, the effects of electrospray process parameters on the size were investigated by Taguchi experimental design. FTIR and TGA approved the presence of both PMMA and EC without further reaction. FE-SEM micrograph demonstrated that an appropriate choice of solvents, utilizing an appropriate PMMA:EC ratio and sufficient PMMA concentration are critical factors to produce capsules dominantly with an intact and spherical morphology. Utilizing various flow rates (0.3–0.5 ml/h) and applied voltage (18–26 kV), capsules were obtained with a 600–1000 nm size range. At constantly applied voltages, the increase in flow rate increased the capsule size up to 40% (ANOVA, p ≤ 0.05), while at constant flow rates, the increase in applied voltage reduced the average capsule size by 3.4–26% (ANOVA, p ≤ 0.05). The results from the Taguchi design represented the significance of solution flow rate, applied voltage, and solution concentration. It was shown that the most effective parameter on the size of capsules is flow rate. This research demonstrated that electrospray can be utilized as a convenient method for the preparation of sub-micron PMMA capsules containing EC. Furthermore, the morphology of the capsules is dominated by solvents, PMMA concentration, and PMMA:EC ratio, while the average size of the capsules can be altered by adjusting the flow rate and applied voltage of the electrospray process.
|
|
6. |
- Anerao, Prashant, et al.
(author)
-
Biochar reinforced PLA composite for fused deposition modelling (FDM): A parametric study on mechanical performance
- 2023
-
In: Composites Part C: Open Access. - : Elsevier B.V.. - 2666-6820. ; 12
-
Journal article (peer-reviewed)abstract
- Rice husk biochar was added to polylactic acid (PLA) to create a biocomposite filament suitable for the extrusion-based 3D printing process of fused deposition modelling (FDM). Taguchi L16 was used for experiment design, and the significance of process parameters was determined using variance analysis (ANOVA). For a 0.3-mm layer thickness, the addition of 5 wt.% biochar resulted in ultimate tensile strength and a modulus of elasticity of 36 MPa and 1103 MPa, respectively. The addition of biochar had a negative influence on flexural strength. The maximum flexural modulus was obtained with 3 % biochar, 100 % infill density, and 0.1 mm layer thickness. Particularly, 1 % biochar resulted in a considerable increase in impact strength, while a subsequent rise in biochar resulted in a decrease, probably due to the agglomeration effect. For 3D printed neat PLA, the average tensile strength, tensile modulus, flexural strength, flexural modulus, and impact strength observed were 19 MPa, 550 MPa, 54 MPa, 1981 MPa, and 25 KJ/m2, respectively. Additionally, considering the output of each test, a multicriteria decision-making model, namely, TOPSIS, has been utilized for ranking the mechanical performance. In order to optimise the mechanical properties of three-dimensional printed objects, the study suggests a layer thickness of 0.2 mm, an infill density of 100 %, and raster angle of 0° as the FDM process parameters.
|
|
7. |
- Babu, Karthik, et al.
(author)
-
A Review on the Flammability Properties of Carbon-Based Polymeric Composites : State-of-the-Art and Future Trends
- 2020
-
In: Polymers. - : MDPI. - 2073-4360. ; 12:7
-
Research review (peer-reviewed)abstract
- Carbon based fillers have attracted a great deal of interest in polymer composites because of their ability to beneficially alter properties at low filler concentration, good interfacial bonding with polymer, availability in different forms, etc. The property alteration of polymer composites makes them versatile for applications in various fields, such as constructions, microelectronics, biomedical, and so on. Devastations due to building fire stress the importance of flame-retardant polymer composites, since they are directly related to human life conservation and safety. Thus, in this review, the significance of carbon-based flame-retardants for polymers is introduced. The effects of a wide variety of carbon-based material addition (such as fullerene, CNTs, graphene, graphite, and so on) on reaction-to-fire of the polymer composites are reviewed and the focus is dedicated to biochar-based reinforcements for use in flame retardant polymer composites. Additionally, the most widely used flammability measuring techniques for polymeric composites are presented. Finally, the key factors and different methods that are used for property enhancement are concluded and the scope for future work is discussed.
|
|
8. |
- Babu, Karthik, et al.
(author)
-
Fire Behavior of 3D-Printed Polymeric Composites
- 2021
-
In: Journal of materials engineering and performance (Print). - : Springer. - 1059-9495 .- 1544-1024. ; 30:7, s. 4745-4755
-
Journal article (peer-reviewed)abstract
- 3D printing or additive manufacturing (AM) is considered as a flexible manufacturing method with the potential for substantial innovations in fabricating geometrically complicated structured polymers, metals, and ceramics parts. Among them, polymeric composites show versatility for applications in various fields, such as constructions, microelectronics and biomedical. However, the poor resistance of these materials against fire must be considered due to their direct relation to human life conservation and safety. In this article, the recent advances in the fire behavior of 3D-printed polymeric composites are reviewed. The article describes the recently developed methods for improving the flame retardancy of 3D-printed polymeric composites. Consequently, the improvements in the fire behavior of 3D-printed polymeric materials through the change in formulation of the composites are discussed. The article is novel in the sense that it is one of the first studies to provide an overview regarding the flammability characteristics of 3D-printed polymeric materials, which will further incite research interests to render AM-based materials fire-resistant.
|
|
9. |
- Babu, NB Karthik, et al.
(author)
-
Self‐reinforced polymer composites: An opportunity to recycle plastic wastes and their future trends
- 2022
-
In: Journal of Applied Polymer Science. - : John Wiley & Sons. - 0021-8995 .- 1097-4628. ; 139:46
-
Research review (peer-reviewed)abstract
- Polymers and their composites have played an important role in industrial development. Polymer composites are becoming much stronger and more competitive than other materials as a result of ongoing research and development. This was made possible by newly developed techniques that could alter the physical and chemical properties of constituents. One of them is the self-reinforcement technique, which allows for the fabrication of high-strength thermoplastic polymer composites with reserved degradability, which is not possible with glass fiber/carbon fiber reinforcement. A self-reinforced polymer composite is made of a single polymeric material, which serves as both the matrix and the reinforcement. This review article discusses the use of self-reinforcement in various polymers and its impact on mechanical, thermal, and fire properties. Furthermore, the effects of process parameters (such as temperature and time, an), reinforcement structure, and mechanical property variation on the structure of self-reinforced composites are reviewed and presented in detail. In addition, the effect of foreign filler addition (such as flame retardants, inorganic particles, natural fibers, etc.) on self-reinforced composites is highlighted. In the end, the need for future research and its scope is presented.
|
|
10. |
- Birdsong, Björn K., et al.
(author)
-
Flexible and fire-retardant silica/cellulose aerogel using bacterial cellulose nanofibrils as template material
- 2024
-
In: Materials Advances. - : Royal Society of Chemistry. - 2633-5409. ; 5:12, s. 5041-5051
-
Journal article (peer-reviewed)abstract
- This study explores the possibility of using various silsesquioxane precursors such as (3-aminopropyl) triethoxysilane (APTES), methyltrimethoxysilane (MTMS), and tetraethyl orthosilicate (TEOS) to produce silsesquioxane-bacterial cellulose nanofibre (bCNF) aerogels. Each precursor allowed to customize the aerogel properties, leading to unique properties suitable for various applications requiring lightweight insulative materials. When utilizing APTES as the silsesquioxane precursor, an aerogel capable of over 90% recovery after compression was formed, making them suitable for flexible applications. When MTMS was used as the precursor, the aerogel retained some compression recovery (80%) but had the added property of superhydrophobicity with a contact angle over 160° due to the presence of CH3 functional groups, enabling water-repellence. Finally, TEOS allowed for excellent thermal insulative properties with a low Peak Heat Release Rate (PHRR), making it a promising candidate for fire-resistant applications. The customization of these aerogel materials was attributed to a combination of the chemical composition of the silsesquioxane precursors and the morphology of the coated bacterial cellulose nanofibres (bCNF), such as CH3 groups found in MTMS enabled for superhydrophobicity. Differences in morphology, such as uniform and smooth silsesquioxane coatings when using APTES or a “pearl-necklace” morphology using TEOS, enabled either compression recovery and flexibility or low thermal conduction. This investigation of silsesquioxane-bCNF provides a good understanding of the importance of the choice of precursor effect on insulating aerogel properties.
|
|