| 1. |
- Biendicho, Jordi Jacas, et al.
(author)
-
New in-situ neutron diffraction cell for electrode materials
- 2014
-
In: Journal of Power Sources. - : Elsevier BV. - 0378-7753 .- 1873-2755. ; 248, s. 900-904
-
Journal article (peer-reviewed)abstract
- A novel neutron diffraction cell has been constructed to allow in-situ studies of the structural changes in materials of relevance to battery applications during charge/discharge cycling. The new design is based on the coin cell geometry, but has larger dimensions compared to typical commercial batteries in order to maximize the amount of electrode material and thus, collect diffraction data of good statistical quality within the shortest possible time. An important aspect of the design is its modular nature, allowing flexibility in both the materials studied and the battery configuration. This paper reports electrochemical tests using a Nickel-metal-hydride battery (Ni-MH), which show that the cell is able to deliver 90% of its theoretical capacity when using deuterated components. Neutron diffraction studies performed on the Polaris diffractometer using nickel metal and a hydrogen-absorbing alloy (MH) clearly show observable changes in the neutron diffraction patterns as a function of the discharge state. Due to the high quality of the diffraction patterns collected in-situ (i.e. good peak-to-background ratio), phase analysis and peak indexing can be performed successfully using data collected in around 30 min. In addition to this, structural parameters for the beta-phase (charged) MH electrode obtained by Rietveld refinement are presented. (C) 2013 The Authors. Published by Elsevier B.V. All rights reserved.
|
|
| 2. |
- Ciosek Högström, Katarzyna, 1984-, et al.
(author)
-
Impact of the flame retardant additive triphenyl phosphate (TPP) on the performance of graphite/LiFePO4 cells in high power applications
- 2014
-
In: Journal of Power Sources. - : Elsevier BV. - 0378-7753 .- 1873-2755. ; 256, s. 430-439
-
Journal article (peer-reviewed)abstract
- This study presents an extensive characterization of a standard Li-ion battery (LiB) electrolyte containing different concentrations of the flame retardant triphenyl phosphate (TPP) in the context of high power applications. Electrolyte characterization shows only a minor decrease in the electrolyte flammability for low TPP concentrations. The addition of TPP to the electrolyte leads to increased viscosity and decreased conductivity. The solvation of the lithium ion charge carriers seem to be directly affected by the TPP addition as evidenced by Raman spectroscopy and increased mass-transport resistivity. Graphite/LiFePO4 full cell tests show the energy efficiency to decrease with the addition of TPP. Specifically, diffusion resistivity is observed to be the main source of increased losses. Furthermore, TPP influences the interface chemistry on both the positive and the negative electrode. Higher concentrations of TPP lead to thicker interface layers on LiFePO4. Even though TPP is not electrochemically reduced on graphite, it does participate in SEI formation. TPP cannot be considered a suitable flame retardant for high power applications as there is only a minor impact of TPP on the flammability of the electrolyte for low concentrations of TPP, and a significant increase in polarization is observed for higher concentrations of TPP. (C) 2014 Elsevier B.V. All rights reserved.
|
|
| 3. |
- Slawinski, Wojciech Andrzej, 1980, et al.
(author)
-
Neutron Pair Distribution Function Study of FePO4 and LiFePO4
- 2019
-
In: Chemistry of Materials. - : American Chemical Society (ACS). - 1520-5002 .- 0897-4756. ; 31:14, s. 5024-5034
-
Journal article (peer-reviewed)abstract
- Neutron powder diffraction studies of the compounds FePO4 and LiFePO4 are reported. Rietveld refinement of the diffraction data provides averaged structures for both materials that are in good agreement with the published structures. In addition, detailed investigations of the short-range ion-ion correlations within each compound have been performed using the reverse Monte Carlo (RMC) modeling of the total scattering (Bragg plus diffuse) data. Although the short-range structural information for LiFePO4 is consistent with the long-range (averaged) picture, a small, but statistically significant, proportion of the anions is displaced away from their ideal sites within the RMC configurations of FePO4. These anion displacements are discussed in terms of a small concentration of Li+/Fe2+ occupying the empty octahedral sites, probably arising from incomplete delithiation of the LiFePO4 and/or antisite (Li+-Fe2+) defects introduced during the delithiation process.
|
|
| 4. |
- Ahlberg Tidblad, Annika, et al.
(author)
-
Future Material Developments for Electric Vehicle Battery Cells Answering Growing Demands from an End-User Perspective
- 2021
-
In: Energies. - : MDPI. - 1996-1073. ; 14:14
-
Research review (peer-reviewed)abstract
- Nowadays, batteries for electric vehicles are expected to have a high energy density, allow fast charging and maintain long cycle life, while providing affordable traction, and complying with stringent safety and environmental standards. Extensive research on novel materials at cell level is hence needed for the continuous improvement of the batteries coupled towards achieving these requirements. This article firstly delves into future developments in electric vehicles from a technology perspective, and the perspective of changing end-user demands. After these end-user needs are defined, their translation into future battery requirements is described. A detailed review of expected material developments follows, to address these dynamic and changing needs. Developments on anodes, cathodes, electrolyte and cell level will be discussed. Finally, a special section will discuss the safety aspects with these increasing end-user demands and how to overcome these issues.
|
|
| 5. |
- Ahlgren, Per, 1960-, et al.
(author)
-
A bibliometric analysis of battery research with the BATTERY 2030+ roadmap as point of departure
- 2022
-
Reports (other academic/artistic)abstract
- In this bibliometric study, we analyze the six battery research subfields identified in the BATTERY 2030+ roadmap: Battery Interface Genome, Materials Acceleration Platform, Recyclability, Smart functionalities: Self-healing, Smart functionalities: Sensing, and Manufacturability. In addition, we analyze the entire research field related to BATTERY 2030+ as a whole, using two operationalizations. We (a) evaluate the European standing in the subfields/the BATTERY 2030+ field in comparison to the rest of the world, and (b) identify strongholds of the subfields/the BATTERY 2030+ field across Europe. For each subfield and the field as a whole, we used seed articles, i.e. articles listed in the BATTERY 2030+ roadmap or cited by such articles, in order to generate additional, similar articles located in an algorithmically obtained classification system. The output of the analysis is publication volumes, field normalized citation impact values with comparisons between country/country aggregates and between organizations, co-publishing networks between countries and organizations, and keyword co-occurrence networks. For the results related to (a), the performance of EU & associated (countries) is similar to China and the aggregate Japan-South Korea-Singapore and well below North America regarding citation impact and with respect to the field as a whole. Exceptions are, however, the subfields Battery Interface Genome and Recyclability. For the results related to (b), there is a large variability in the EU & associated organizations regarding volume in the different subfields. For citation impact, examples of high-performing EU & associated organizations are ETH Zurich and Max Planck Society for the Advancement of Science.
|
|
| 6. |
- Ahlgren, Per, 1960-, et al.
(author)
-
BATTERY 2030+ and its Research Roadmap : A Bibliometric Analysis.
- 2023
-
In: ChemSusChem. - : Wiley. - 1864-5631 .- 1864-564X. ; 16:21
-
Journal article (peer-reviewed)abstract
- In this bibliometric study, we analyze two of the six battery research subfields identified in the BATTERY 2030+ roadmap: Materials Acceleration Platform and Smart functionalities: Sensing. In addition, we analyze the entire research field related to BATTERY 2030+ as a whole. We (a) evaluate the European standing in the two subfields/the BATTERY 2030+ field in comparison to the rest of the world, and (b) identify strongholds of the two subfields/the BATTERY 2030+ field across Europe. For each subfield and the field as a whole, we used seed articles, i. e. articles listed in the BATTERY 2030+ roadmap or cited by such articles, in order to generate additional, similar articles located in an algorithmically obtained classification system. The output of the analysis is publication volumes, field normalized citation impact values with comparisons between country/country aggregates and between organizations, co-publishing networks between countries and organizations, and keyword co-occurrence networks.
|
|
| 7. |
- Aktekin, Burak, et al.
(author)
-
Cation Ordering and Oxygen Release in LiNi0.5-xMn1.5+xO4-y (LNMO) : In Situ Neutron Diffraction and Performance in Li Ion Full Cells
- 2019
-
In: ACS Applied Energy Materials. - : AMER CHEMICAL SOC. - 2574-0962. ; 2:5, s. 3323-3335
-
Journal article (peer-reviewed)abstract
- Lithium ion cells utilizing LiNi0.5Mn1.5O4 (LNMO) as the positive electrode are prone to fast capacity fading, especially when operated in full cells and at elevated temperatures. The crystal structure of LNMO can adopt a P4(3)32 (cation-ordered) or Fd (3) over barm (disordered) arrangement, and the fading rate of cells is usually mitigated when samples possess the latter structure. However, synthesis conditions leading to disordering also lead to oxygen deficiencies and rock-salt impurities and as a result generate Mn3+. In this study, in situ neutron diffraction was performed on disordered and slightly Mn-rich LNMO samples to follow cation ordering-disordering transformations during heating and cooling. The study shows for the first time that there is not a direct connection between oxygen release and cation disordering, as cation disordering is observed to start prior to oxygen release when the samples are heated in a pure oxygen atmosphere. This result demonstrates that it is possible to tune disordering in LNMO without inducing oxygen deficiencies or forming the rock-salt impurity phase. In the second part of the study, electrochemical testing of samples with different degrees of ordering and oxygen content has been performed in LNMO vertical bar vertical bar LTO (Li4Ti5O12) full cells. The disordered sample exhibits better performance, as has been reported in other studies; however, we observe that all cells behave similarly during the initial period of cycling even when discharged at a 10 C rate, while differences arise only after a period of cycling. Additionally, the differences in fading rate were observed to be time-dependent rather than dependent on the number of cycles. This performance degradation is believed to be related to instabilities in LNMO at higher voltages, that is, in its lower lithiation states. Therefore, it is suggested that future studies should target the individual effects of ordering and oxygen content. It is also suggested that more emphasis during electrochemical testing should be placed on the stability of samples in their delithiated state.
|
|
| 8. |
- Aktekin, Burak, et al.
(author)
-
Cation Ordering and Oxygen Release in LiNi0.5-xMn1.5+xO4-y (LNMO)—In Situ Neutron Diffraction and Performance in Li-Ion Full Cells
- 2018
-
Conference paper (peer-reviewed)abstract
- LiNi0.5Mn1.5O4 (LNMO) is a promising spinel-type positive electrode for lithium ion batteries as it operates at high voltage and possesses high power capability. However, rapid performance degradation in full cells, especially at elevated temperatures, is a problem. There has been a considerable interest in its crystal structure as this is known to affect its electrochemical performance. LNMO can adopt a P4332 (cation ordered) or Fd-3m (cation disordered) arrangement depending on the synthesis conditions. Most of the studies in literature agree on better electrochemical performance for disordered LNMO [1], however, a clear understanding of the reason for this behaviour is still lacking. This partly arises from the fact that synthesis conditions leading to disordering also lead to oxygen deficiency, rock-salt impurities and therefore generate some Mn3+ [2]. Most commonly, X-ray diffraction is used to characterize these materials, however, accurate structural analysis is difficult due to the near identical scattering lengths of Mn and Ni. This is not the case for neutron diffraction. In this study, an in-situ neutron diffraction heating-cooling experiment was conducted on slightly Mn-rich LNMO under pure oxygen atmosphere in order to investigate relationship between disordering and oxygen deficiency. The study shows for the first time that there is no direct relationship between oxygen loss and cation disordering, as disordering starts prior to oxygen release. Our findings suggest that it is possible to obtain samples with varying degrees of ordering, yet with the same oxygen content and free from impurities. In the second part of the study, highly ordered, partially ordered and fully disordered samples have been tested in LNMO∥LTO (Li4Ti5O12) full cells at 55 °C. It is shown that differences in their performances arise only after repeated cycling, while all the samples behave similarly at the beginning of the test. The difference is believed to be related to instabilities of LNMO at higher voltages, that is, in its lower lithiation states.[1] A. Manthiram, K. Chemelewski, E.-S. Lee, Energy Environ. Sci. 7 (2014) 1339.[2] M. Kunduraci, G.G. Amatucci, J. Power Sources. 165 (2007) 359–367.
|
|
| 9. |
- Aktekin, Burak, et al.
(author)
-
Concentrated LiFSI-€“Ethylene Carbonate Electrolytes and Their Compatibility with High-Capacity and High-Voltage Electrodes
- 2022
-
In: ACS Applied Energy Materials. - : American Chemical Society (ACS). - 2574-0962. ; 5:1, s. 585-595
-
Journal article (peer-reviewed)abstract
- The unusual physical and chemical properties of electrolytes with excessive salt contents have resulted in rising interest in highly concentrated electrolytes, especially for their application in batteries. Here, we report strikingly good electrochemical performance in terms of conductivity and stability for a binary electrolyte system, consisting of lithium bis(fluorosulfonyl)imide (LiFSI) salt and ethylene carbonate (EC) solvent. The electrolyte is explored for different cell configurations spanning both high-capacity and high-voltage electrodes, which are well known for incompatibilities with conventional electrolyte systems: Li metal, Si/graphite composites, LiNi0.33Mn0.33Co0.33O2 (NMC111), and LiNi0.5Mn1.5O4 (LNMO). As compared to a LiTFSI counterpart as well as a common LP40 electrolyte, it is seen that the LiFSI:EC electrolyte system is superior in Li-metal–Si/graphite cells. Moreover, in the absence of Li metal, it is possible to use highly concentrated electrolytes (e.g., 1:2 salt:solvent molar ratio), and a considerable improvement on the electrochemical performance of NMC111-Si/graphite cells was achieved with the LiFSI:EC 1:2 electrolyte both at the room temperature and elevated temperature (55 °C). Surface characterization with scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) showed the presence of thicker surface film formation with the LiFSI-based electrolyte as compared to the reference electrolyte (LP40) for both positive and negative electrodes, indicating better passivation ability of such surface films during extended cycling. Despite displaying good stability with the NMC111 positive electrode, the LiFSI-based electrolyte showed less compatibility with the high-voltage spinel LNMO electrode (4.7 V vs Li+/Li).
|
|
| 10. |
- Aktekin, Burak, et al.
(author)
-
How Mn/Ni Ordering Controls Electrochemical Performance in High-Voltage Spinel LiNi0.44Mn1.56O4 with Fixed Oxygen Content
- 2020
-
In: ACS Applied Energy Materials. - : AMER CHEMICAL SOC. - 2574-0962. ; 3:6, s. 6001-6013
-
Journal article (peer-reviewed)abstract
- The crystal structure of LiNi0.5O4 (LNMO) can adopt either low-symmetry ordered (Fd (3) over barm) or high-symmetry disordered (P4(3)32) space group depending on the synthesis conditions. A majority of published studies agree on superior electrochemical performance of disordered LNMO, but the underlying reasons for improvement remain unclear due to the fact that different thermal history of the samples affects other material properties such as oxygen content and particle morphology. In this study, ordered and disordered samples were prepared with a new strategy that renders samples with identical properties apart from their cation ordering degree. This was achieved by heat treatment of powders under pure oxygen atmosphere at high temperature with a final annealing step at 710 degrees C for both samples, followed by slow or fast cooling. Electrochemical testing showed that cation disordering improves the stability of material in charged (delithiated) state and mitigates the impedance rise in LNMO parallel to LTO (Li4Ti5O12) and LNMO parallel to Li cells. Through X-ray photoelectron spectroscopy (XPS), thicker surface films were observed on the ordered material, indicating more electrolyte side reactions. The ordered samples also showed significant changes in the Ni 2p XPS spectra, while the generation of ligand (oxygen) holes was observed in the Ni-O environment for both samples using X-ray absorption spectroscopy (XAS) and resonant inelastic X-ray scattering (RIXS). Moreover, high-resolution transmission electron microscopy (HRTEM) images indicated that the ordered samples show a decrease in ordering near the particle surface after cycling and a tendency toward rock-salt-like phase transformations. These results show that the structural arrangement of Mn/Ni (alone) has an effect on the surface and "nearsurface" properties of LNMO, particularly in delithiated state, which is likely connected to the bulk electronic properties of this electrode material.
|
|
