| 1. |
|
|
| 2. |
- Filho, Luimar, et al.
(author)
-
The effect of N, C, Cr, and Nb content on silicon nitride coatings for joint applications
- 2020
-
In: Materials. - : MDPI AG. - 1996-1944. ; 13:8
-
Journal article (peer-reviewed)abstract
- Ceramic coatings are an alternative to achieve or maintain a high wear resistance of metallic surfaces, and simultaneously allow for a reduction in metal ion release. Silicon nitride based (SiNx) coatings deposited by high power impulse magnetron sputtering (HiPIMS) have shown potential for use in joint implants seen from an improved chemical stability in combination with a good adhesion. The aim of this study was to investigate the effect of N, C, Cr and Nb content on the tribocorrosive performance of 3.7 to 8.8 µm thick SiNx coatings deposited by HiPIMS onto CoCrMo discs to improve the mechanical properties and/or chemical stability of SiNx .Coating composition was evaluated by X-ray photoelectron spectroscopy (XPS) and the surface roughness by Vertical Scanning Interferometry (VSI). Hardness and Young’s modulus were investigated by nanoindentation and coating adhesion was measured by scratch tests. Multidirectional wear tests against UHMWPE pins were performed for 2 million cycles in bovine serum solution (25%) at 37°C, at an estimated contact pressure of 2.1 MPa.Coatings with a relatively low hardness tended to fail earlier in the wear test, due to chemical reactions and eventually dissolution, accelerated by the tribological contact. In fact, while no definite correlation could be observed between coating composition (N: 42.6-55.5 at%, C: 0-25.7 at%, Cr: 0 or 12.8 at%, and Nb: 0-24.5 at%) and wear performance, it was apparent that high-purity and/or -density coatings (i.e. low oxygen content and high nitrogen content) were desirable to prevent coating and/or counter surface wear. Coatings deposited with a higher energy fulfilled the target profile in terms of low surface roughness (Ra<20nm), adequate adhesion (Lc2>30N), chemical stability over time in the tribocorrosive environment, as well as low polymer wear, presenting potential for a future application in joint bearings.
|
|
| 3. |
|
|
| 4. |
|
|
| 5. |
- Bang, Le T., et al.
(author)
-
Synthesis and assessment of metallic ion migration through a novel calcium carbonate coating for biomedical implants
- 2020
-
In: Journal of Biomedical Materials Research. Part B - Applied biomaterials. - : Wiley. - 1552-4973 .- 1552-4981. ; 108:2, s. 429-438
-
Journal article (peer-reviewed)abstract
- Titanium (Ti) implants are commonly regarded as well accepted by the body. However, metal ion release is still a cause for concern. A small decrease in pH, which can be caused by inflammation, may produce a large increase in the corrosion rate of Ti implants. Coating the alloy with a buffer layer could have a significant protective effect. In this study, a calcium carbonate coating was developed on commercially pure Ti and a Ti-6Al-4V alloy through a hydrothermal treatment of previously NaOH-treated surfaces in calcium-citric acid chelate complexes. The results showed that a superstructured calcite coating layer formed on the Ti substrate after treatment at 170 degrees C for 3 hr. The coating was approx. 1 mu m thick and covered the substrate surface uniformly. When prolonging the hydrothermal treatment from 5 hr to 24 hr, the rhombohedral structure of calcite was observed in addition to the superstructure of calcite. Dissolution test results showed no significant differences in solution pH between the coated- and un-coated samples. However, the CaCO3 coating reduced by approx. 2-5 times the Ti and V ion release from the substrate as compared to the uncoated material, at pH 4. CaCO3 and hydroxyapatite (HA) coatings gave nonsignificant effects at neutral pH although the HA coating showed a trend for better results at the longer time points. The reduction in metal ion release from the substrate and the buffering ability of the CaCO3 coating encourage further studies on this coating for clinical applications.
|
|
| 6. |
- Bojan, Alicja J., 1980, et al.
(author)
-
A new bone adhesive candidate- does it work in human bone? An ex-vivo preclinical evaluation in fresh human osteoporotic femoral head bone
- 2022
-
In: Injury-International Journal of the Care of the Injured. - : Elsevier BV. - 0020-1383 .- 1879-0267. ; 53:6, s. 1858-1866
-
Journal article (peer-reviewed)abstract
- Introduction: The fixation of small intraarticular bone fragments is clinically challenging and an obvious first orthopaedic indication for an effective bone adhesive. In the present study the feasibility of bonding freshly harvested human trabecular bone with OsStic(R), a novel phosphoserine modified cement, was evaluated using a bone cylinder model pull-out test and compared with a commercial fibrin tissue adhesive. Methods: Femoral heads (n=13) were collected from hip fracture patients undergoing arthroplasty and stored refrigerated overnight in saline medium prior to testing. Cylindrical bone cores with a pre-inserted bone screw, were prepared using a coring tool. Each core was removed and glued back in place with either the bone adhesive (alpha-tricalcium phosphate, phosphoserine and 20% trisodium citrate solution) or the fibrin glue. All glued bones were stored in bone medium at 37 degrees C. Tensile loading, using a universal testing machine (5 kN load cell), was applied to each core/head. For the bone adhesive, bone cores were tested at 2 (n=13) and 24 (n=11) hours. For the fibrin tissue adhesive control group (n=9), bone cores were tested exclusively at 2 hours. The femoral bone quality was evaluated with micro-CT. Results: The ultimate pull-out load for the bone adhesive at 2 hours ranged from 36 to 171 N (mean 94 N, SD 42 N). At 24 hours the pull-out strength was similar, 47 to 198 N (mean 123 N, SD 43 N). The adhesive failure usually occurred through the adhesive layer, however in two samples, at 167 N and 198 N the screw pulled out of the bone core. The fibrin tissue adhesive group reached a peak force of 8 N maximally at 2 hours (range 2.8-8 N, mean 5.4 N, SD 1.6 N). The mean BV/TV for femoral heads was 0.15 and indicates poor bone quality. Conclusion: The bone adhesive successfully glued wet and fatty tissue of osteoporotic human bone cores. The mean ultimate pull-out force of 123 N at 24 hours corresponds to similar to 300 kPa shear stress acting on the bone core. These first ex-vivo results in human bone are a promising step toward potential clinical application in osteochondral fragment fixation. (C) 2022 The Authors. Published by Elsevier Ltd.
|
|
| 7. |
|
|
| 8. |
- Dong, Zhiyun, et al.
(author)
-
Silk fibroin hydrogels induced and reinforced by acidic calcium phosphate : A simple way of producing bioactive and drug-loadable composites for biomedical applications
- 2021
-
In: International Journal of Biological Macromolecules. - : Elsevier. - 0141-8130 .- 1879-0003. ; 193, s. 433-440
-
Journal article (peer-reviewed)abstract
- Silk fibroin (SF) hydrogels have attracted extensive interest in biomedical applications due to their biocompatibility and wide availability. However, their generally poor mechanical properties limit their utility. Here, injectable, ready-to-use SF-based composites, simultaneously induced and reinforced by acidic calcium phosphates, were prepared via a dual-paste system requiring no complex chemical/physical treatment. The composite was formed by mixing a monocalcium phosphate monohydrate paste with a β-tricalcium phosphate/SF paste. The conformational transition of SF in an acidic environment forms continuous networks, and the acidic calcium phosphate, brushite and monetite, formed simultaneously in the networks during mixing. The composites displayed a partly elastomeric compression behavior, with mechanical properties increasing with an increasing calcium phosphate and β-sheet content at the lower calcium phosphate contents evaluated (22.2–36.4 wt%). While the stiffness was still relatively low, the materials presented a high elasticity and ductility, and no failure at stresses in the range of failure stresses of trabecular bone. Furthermore, the calcium phosphate confers bioactivity to the material, and the composites with a promising in vitro cell response also showed potential as drug vehicles, using vancomycin as a model drug. These dual-paste systems exhibit potential utility in biomedical applications, such as bone void fillers and drug vehicles.
|
|
| 9. |
- Engqvist, Cecilia, et al.
(author)
-
Interactions between single latex particles and silica surfaces studied with AFM
- 2007
-
In: Colloids and Surfaces A. - : Elsevier BV. - 0927-7757 .- 1873-4359. ; 302:03-jan, s. 197-203
-
Journal article (peer-reviewed)abstract
- The spreading of single styrene-acrylic latex particles on silicon oxide C surfaces was studied using atomic force microscopy (AFM). Three latexes with different glass transition temperature (Tg) were used and the effects of temperature, time and preparation method were investigated. Particle sizes and shape were measured with AFM and the contact angles were calculated. The observed rate for the spreading of latex particles was low and it took several days before the particles reached steady state, even at temperatures well above their T-g. The experimental particle spreading results deviated with two orders of magnitude from predictions Using the WLF equation for polymer diffusion. The deviation could be attributed to polymer-surface interactions that slowed down the particle spreading. The work of adhesion was calculated using two models. The results from using the regular Young-Dupre equation and a modified version of this equation that also included the mechanical properties (E-modulus and Poisson's ratio) of the latexes, were compared. For soft latex particles the results from the two models agreed well and were of the order of 75 J/m(2), but for glassy latexes the Young-Dupre equation underestimated the work of adhesion.
|
|
| 10. |
- Engstrand, Johanna, et al.
(author)
-
Influence of polymer addition on the mechanical properties of a premixed calcium phosphate cement
- 2013
-
In: Biomatter. - : Informa UK Limited. - 2159-2535. ; 3:4, s. e27249-
-
Journal article (peer-reviewed)abstract
- Premixed calcium phosphate cements can reduce handling complications that are associated with the mixing of cements in the operating room. However, to extend the clinical indication of ceramic cements their mechanical properties need to be further improved. The incorporation of a polymeric material with intrinsically high tensile properties could possibly assist in increasing the mechanical properties of calcium phosphate cement. In this study polymer microparticles made from poly(lactid-co-glycolide) plasticised with poly(ethylene glycol) 400 (PLGA/PEG microparticles) were added in amounts of up to 5 wt% to a premixed acidic calcium phosphate cement. The PLGA/PEG microparticles added undergo a shape transformation at 37°C, which could give a better integration between polymer microparticles and ceramic cement compared to polymer microparticles lacking this property. The results showed that the incorporation of 1.25 wt% PLGA/PEG microparticles increased the compressive strength by approximately 20% up to 15.1 MPa while the diametral tensile strength was kept constant. The incorporation of PLGA/PEG microparticles increased the brushite to monetite ratio after setting compared to pure ceramic cements. In conclusion, small amounts of PLGA/PEG microparticles can be incorporated into premixed acidic calcium phosphate cement and increase their mechanical properties, which could lead to increased future applications.
|
|
