1. |
- Abdesselam, A., et al.
(author)
-
The ATLAS semiconductor tracker end-cap module
- 2007
-
In: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576. ; 575:3, s. 353-389
-
Journal article (peer-reviewed)abstract
- The challenges for the tracking detector systems at the LHC are unprecedented in terms of the number of channels, the required read-out speed and the expected radiation levels. The ATLAS Semiconductor Tracker. (SCT) end-caps have a total of about 3 million electronics channels each reading out every 25 ns into its own on-chip 3.3 mu s buffer. The highest anticipated dose after 10 years operation is 1.4x10(14) cm(-2) in units of 1 MeV neutron equivalent (assuming the damage factors scale with the non-ionising energy loss). The forward tracker has 1976 double-sided modules, mostly of area similar to 70 cm(2), each having 2 x 768 strips read out by six ASICs per side. The requirement to achieve an average perpendicular radiation length of 1.5% X-0, while coping with up to 7 W dissipation per module (after irradiation), leads to stringent constraints on the thermal design. The additional requirement of 1500e(-) equivalent noise charge (ENC) rising to only 1800e(-) ENC after irradiation, provides stringent design constraints on both the high-density Cu/Polyimide flex read-out circuit and the ABCD3TA read-out ASICs. Finally, the accuracy of module assembly must not compromise the 16 mu m (r phi) resolution perpendicular to the strip directions or 580 mu m radial resolution coming from the 40 mrad front-back stereo angle. A total of 2210 modules were built to the tight tolerances and specifications required for the SCT. This was 234 more than the 1976 required and represents a yield of 93%. The component flow was at times tight, but the module production rate of 40-50 per week was maintained despite this. The distributed production was not found to be a major logistical problem and it allowed additional flexibility to take advantage of where the effort was available, including any spare capacity, for building the end-cap modules. The collaboration that produced the ATLAS SCT end-cap modules kept in close contact at all times so that the effects of shortages or stoppages at different sites could be rapidly resolved.
|
|
2. |
- Abdesselam, A., et al.
(author)
-
Engineering for the ATLAS SemiConductor Tracker (SCT) end-cap
- 2008
-
In: Journal of Instrumentation. - 1748-0221. ; 3
-
Journal article (peer-reviewed)abstract
- The ATLAS SemiConductor Tracker (SCT) is a silicon-strip tracking detector which forms part of the ATLAS inner detector. The SCT is designed to track charged particles produced in proton-proton collisions at the Large Hadron Collider (LHC) at CERN at an energy of 14 TeV. The tracker is made up of a central barrel and two identical end-caps. The barrel contains 2112 silicon modules, while each end-cap contains 988 modules. The overall tracking performance depends not only on the intrinsic measurement precision of the modules but also on the characteristics of the whole assembly, in particular, the stability and the total material budget. This paper describes the engineering design and construction of the SCT end-caps, which are required to support mechanically the silicon modules, supply services to them and provide a suitable environment within the inner detector. Critical engineering choices are highlighted and innovative solutions are presented - these will be of interest to other builders of large-scale tracking detectors. The SCT end-caps will be fully connected at the start of 2008. Further commissioning will continue, to be ready for proton-proton collision data in 2008.
|
|
3. |
- Abdesselam, A., et al.
(author)
-
The barrel modules of the ATLAS semiconductor tracker
- 2006
-
In: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576. ; 568:2, s. 642-671
-
Journal article (peer-reviewed)abstract
- This paper describes the silicon microstrip modules in the barrel section of the SemiConductor Tracker (SCT) of the ATLAS experiment at the CERN Large Hadron Collider (LHC). The module requirements, components and assembly techniques are given, as well as first results of the module performance on the fully assembled barrels that make up the detector being installed in the ATLAS experiment.
|
|
4. |
- Poley, L., et al.
(author)
-
The ABC130 barrel module prototyping programme for the ATLAS strip tracker
- 2020
-
In: Journal of Instrumentation. - : IOP PUBLISHING LTD. - 1748-0221. ; 15:9
-
Journal article (peer-reviewed)abstract
- For the Phase-II Upgrade of the ATLAS Detector [1], its Inner Detector, consisting of silicon pixel, silicon strip and transition radiation sub-detectors, will be replaced with an all new 100% silicon tracker, composed of a pixel tracker at inner radii and a strip tracker at outer radii. The future ATLAS strip tracker will include 11,000 silicon sensor modules in the central region (barrel) and 7,000 modules in the forward region (end-caps), which are foreseen to be constructed over a period of 3.5 years. The construction of each module consists of a series of assembly and quality control steps, which were engineered to be identical for all production sites. In order to develop the tooling and procedures for assembly and testing of these modules, two series of major prototyping programs were conducted: an early program using readout chips designed using a 250 nm fabrication process (ABCN-250) [2, 3] and a subsequent program using a follow-up chip set made using 130 nm processing (ABC130 and HCC130 chips). This second generation of readout chips was used for an extensive prototyping program that produced around 100 barrel-type modules and contributed significantly to the development of the final module layout. This paper gives an overview of the components used in ABC130 barrel modules, their assembly procedure and findings resulting from their tests.
|
|
5. |
- Diez, S., et al.
(author)
-
A double-sided, shield-less stave prototype for the ATLAS Upgrade strip tracker for the High Luminosity LHC
- 2014
-
In: Journal of Instrumentation. - 1748-0221. ; 9, s. P03012-
-
Journal article (peer-reviewed)abstract
- A detailed description of the integration structures for the barrel region of the silicon strips tracker of the ATLAS Phase-II upgrade for the upgrade of the Large Hadron Collider, the so-called High Luminosity LHC (HL-LHC), is presented. This paper focuses on one of the latest demonstrator prototypes recently assembled, with numerous unique features. It consists of a shortened, shield-less, and double sided stave, with two candidate power distributions implemented. Thermal and electrical performances of the prototype are presented, as well as a description of the assembly procedures and tools.
|
|
6. |
- Gonzalez-Sevilla, S., et al.
(author)
-
A double-sided silicon micro-strip Super-Module for the ATLAS Inner Detector upgrade in the High-Luminosity LHC
- 2014
-
In: Journal of Instrumentation. - 1748-0221. ; 9, s. P02003-
-
Journal article (peer-reviewed)abstract
- The ATLAS experiment is a general purpose detector aiming to fully exploit the discovery potential of the Large Hadron Collider (LHC) at CERN. It is foreseen that after several years of successful data-taking, the LHC physics programme will be extended in the so-called High-Luminosity LHC, where the instantaneous luminosity will be increased up to 5 x 10(34) cm(-2) s(-1). For ATLAS, an upgrade scenario will imply the complete replacement of its internal tracker, as the existing detector will not provide the required performance due to the cumulated radiation damage and the increase in the detector occupancy. The current baseline layout for the new ATLAS tracker is an all-silicon-based detector, with pixel sensors in the inner layers and silicon micro-strip detectors at intermediate and outer radii. The super-module is an integration concept proposed for the strip region of the future ATLAS tracker, where double-sided stereo silicon micro-strip modules are assembled into a low-mass local support structure. An electrical super-module prototype for eight double-sided strip modules has been constructed. The aim is to exercise the multi-module readout chain and to investigate the noise performance of such a system. In this paper, the main components of the current super-module prototype are described and its electrical performance is presented in detail.
|
|
7. |
- Rubin, D., et al.
(author)
-
Looking Beyond Lambda with the Union Supernova Compilation
- 2009
-
In: Astrophysical Journal. - 0004-637X .- 1538-4357. ; 695, s. 391-403
-
Journal article (peer-reviewed)abstract
- The recent robust and homogeneous analysis of the world's supernova distance-redshift data, together with cosmic microwave background and baryon acoustic oscillation data—provides a powerful tool for constraining cosmological models. Here we examine particular classes of scalar field, modified gravity, and phenomenological models to assess whether they are consistent with observations even when their behavior deviates from the cosmological constant Λ. Some models have tension with the data, while others survive only by approaching the cosmological constant, and a couple are statistically favored over Λ cold dark matter. Dark energy described by two equation-of-state parameters has considerable phase space to avoid Λ and next-generation data will be required to constrain such physics, with the level of complementarity between probes varying with cosmology.
|
|
8. |
- Barbary, K., et al.
(author)
-
Discovery of an Unusual Optical Transient with the Hubble Space Telescope
- 2009
-
In: Astrophysical Journal. - 0004-637X .- 1538-4357. ; 690, s. 1358-1362
-
Journal article (peer-reviewed)abstract
- We present observations of SCP 06F6, an unusual optical transient discovered during the Hubble Space Telescope Cluster Supernova Survey. The transient brightened over a period of ~100 days, reached a peak magnitude of ~ 21.0 in both i 775 and z 850, and then declined over a similar timescale. There is no host galaxy or progenitor star detected at the location of the transient to a 3σ upper limit of i 775 >= 26.4 and z 850 >= 26.1, giving a corresponding lower limit on the flux increase of a factor of ~ 120. Multiple spectra show five broad absorption bands between 4100 Å and 6500 Å, and a mostly featureless continuum longward of 6500 Å. The shape of the light curve is inconsistent with microlensing. The transient's spectrum, in addition to being inconsistent with all known supernova types, does not match any spectrum in the Sloan Digital Sky Survey database. We suggest that the transient may be one of a new class. Based in part on observations made with the NASA/ESA Hubble Space Telescope, obtained from the data archive at the Space Telescope Science Institute (STScI). STScI is operated by the Association of Universities for Research in Astronomy (AURA), Inc. under the NASA contract NAS 5-26555. The observations are associated with program GO-10496. Based in part on observations obtained at the European Southern Observatory under ESO program 077.A-0110. Based in part on observations collected at Subaru Telescope, which is operated by the National Astronomical Observatory of Japan. Some of the data presented herein were obtained at the W.M. Keck Observatory, which is operated as a scientific partnership among the California Institute of Technology, the University of California, and NASA.
|
|
9. |
|
|
10. |
- Dawson, K. S., et al.
(author)
-
An Intensive Hubble Space Telescope Survey for z>1 Type Ia Supernovae by Targeting Galaxy Clusters
- 2009
-
In: Astronomical Journal. - : American Astronomical Society. - 0004-6256 .- 1538-3881. ; 138, s. 1271-1283
-
Journal article (peer-reviewed)abstract
- We present a new survey strategy to discover and study high-redshift Type Ia supernovae (SNe Ia) using the Hubble Space Telescope (HST). By targeting massive galaxy clusters at 0.9 < z < 1.5, we obtain a twofold improvement in the efficiency of finding SNe compared to an HST field survey and a factor of 3 improvement in the total yield of SN detections in relatively dust-free red-sequence galaxies. In total, sixteen SNe were discovered at z>0.95, nine of which were in galaxy clusters. This strategy provides an SN sample that can be used to decouple the effects of host-galaxy extinction and intrinsic color in high-redshift SNe, thereby reducing one of the largest systematic uncertainties in SN cosmology. Based on observations made with the NASA/ESA Hubble Space Telescope and obtained from the data archive at the Space Telescope Institute. STScI is operated by the Association of Universities for Research in Astronomy, Inc. under the NASA contract NAS 5-26555. The observations are associated with program 10496.
|
|