1. |
- Hultman, Erik
(author)
-
Robotized Production Methods for Special Electric Machines
- 2018
-
Doctoral thesis (other academic/artistic)abstract
- A research project on renewable energy conversion from ocean waves to electricity was started at the Division of Electricity at Uppsala University (UU) in 2001. The Wave Energy Converter (WEC) unit developed in this project is intended to be used in large offshore WEC farms and has therefore been designed with large-scale production in mind. The concept has now also been commercialized by the spin-off company Seabased Industry AB.An essential part of the UU WEC is the linear direct-drive generator. This thesis presents the pilot work on developing robotized production methods for this special electric machine. The generator design is here investigated and four different backbreaking, monotone, potentially hazardous and time consuming manual production tasks are selected for automation. A robot cell with special automation equipment is then developed and constructed for each task. Simplicity, reliability and flexibility are prioritized and older model pre-owned industrial robots are used throughout the work. The robot cells are evaluated both analytically and experimentally, with focus on full scale experiments. It is likely that the developed production methods can be applied also for other similar electric machines.The main focus in the thesis is on robotized stator cable winding. The here presented robot cell is, to the knowledge of the author, the first fully automated stator cable winding setup. Fully automated winding with high and consistent quality and high flexibility is demonstrated. Significant potential cost savings compared to manual winding are also indicated. The robot cell is well prepared for production, but further work is required to improve its reliability.The other three developed robot cells are used for stator stacking, surface mounting of permanent magnets on translators and machining of rubber discs. All robot cell concepts are experimentally validated and considerable potential cost savings compared to manual production are indicated. Further work is however required with regards to autonomy and reliability.Finally, the thesis presents a pedagogical development work connected to the research on robotized production methods. A first cycle course on automation and robot engineering is here completely reworked, as it is structured around three real-world group project tasks. The new course is evaluated from the examination results, the students’ course evaluations and the feedback from the teachers during six years. The students greatly appreciated the new course. It is indicated that the developed teaching approach is effective in teaching both classical and modern engineering skills.
|
|
2. |
- Luterbacher, Jürg, et al.
(author)
-
Circulation dynamics and its influence on European and Mediterranean January–April climate over the past half millennium : results and insights from instrumental data,documentary evidence and coupled climate models
- 2010
-
In: Climatic Change. - Netherlands : Springer. - 0165-0009 .- 1573-1480. ; 101:1-2, s. 201-234
-
Journal article (peer-reviewed)abstract
- We use long instrumental temperature series together with available field reconstructions of sea-level pressure (SLP) and three-dimensional climate modelsimulations to analyze relations between temperature anomalies and atmospheric circulation patterns over much of Europe and the Mediterranean for the late winter/early spring (January–April, JFMA) season. A Canonical Correlation Analysis(CCA) investigates interannual to interdecadal covariability between a new gridded SLP field reconstruction and seven long instrumental temperature series covering the past 250 years. We then present and discuss prominent atmospheric circulation patterns related to anomalous warm and cold JFMA conditions within different European areas spanning the period 1760–2007. Next, using a data assimilation technique, we link gridded SLP data with a climate model (EC-Bilt-Clio) for a better dynamical understanding of the relationship between large scale circulationand European climate. We thus present an alternative approach to reconstruct climate for the pre-instrumental period based on the assimilated model simulations.Furthermore, we present an independent method to extend the dynamic circulation analysis for anomalously cold European JFMA conditions back to the sixteenth century. To this end, we use documentary records that are spatially representative for the long instrumental records and derive, through modern analogs, large-scale SLP, surface temperature and precipitation fields. The skill of the analog method is tested in the virtual world of two three-dimensional climate simulations (ECHOGand HadCM3). This endeavor offers new possibilities to both constrain climate model into a reconstruction mode (through the assimilation approach) and to better assess documentary data in a quantitative way.
|
|
3. |
- McGinn, Steven, et al.
(author)
-
New Technologies for DNA analysis-A review of the READNA Project.
- 2016
-
In: New Biotechnology. - : Elsevier BV. - 1876-4347 .- 1871-6784.
-
Research review (peer-reviewed)abstract
- The REvolutionary Approaches and Devices for Nucleic Acid analysis (READNA) project received funding from the European Commission for 4 1/2 years. The objectives of the project revolved around technological developments in nucleic acid analysis. The project partners have discovered, created and developed a huge body of insights into nucleic acid analysis, ranging from improvements and implementation of current technologies to the most promising sequencing technologies that constitute a 3(rd) and 4(th) generation of sequencing methods with nanopores and in situ sequencing, respectively.
|
|
4. |
- Tronnier, Volker M., et al.
(author)
-
The appropriate management of persisting pain after spine surgery : a European panel study with recommendations based on the RAND/UCLA method
- 2019
-
In: European spine journal. - : Springer. - 0940-6719 .- 1432-0932. ; 28:1, s. 31-45
-
Journal article (peer-reviewed)abstract
- Purpose: Management of patients with persisting pain after spine surgery (PPSS) shows significant variability, and there is limited evidence from clinical studies to support treatment choice in daily practice. This study aimed to develop patient-specific recommendations on the management of PPSS.Methods: Using the RAND/UCLA appropriateness method (RUAM), an international panel of 6 neurosurgeons, 6 pain specialists, and 6 orthopaedic surgeons assessed the appropriateness of 4 treatment options (conservative, minimally invasive, neurostimulation, and re-operation) for 210 clinical scenarios. These scenarios were unique combinations of patient characteristics considered relevant to treatment choice. Appropriateness had to be expressed on a 9-point scale (1 = extremely inappropriate, 9 = extremely appropriate). A treatment was considered appropriate if the median score was ≥ 7 in the absence of disagreement (≥ 1/3 of ratings in each of the opposite sections 1–3 and 7–9).Results: Appropriateness outcomes showed clear and specific patterns. In 48% of the scenarios, exclusively one of the 4 treatments was appropriate. Conservative treatment was usually considered appropriate for patients without clear anatomic abnormalities and for those with new pain differing from the original symptoms. Neurostimulation was considered appropriate in the case of (predominant) neuropathic leg pain in the absence of conditions that may require surgical intervention. Re-operation could be considered for patients with recurrent disc, spinal/foraminal stenosis, or spinal instability.Conclusions: Using the RUAM, an international multidisciplinary panel established criteria for appropriate treatment choice in patients with PPSS. These may be helpful to educate physicians and to improve consistency and quality of care.
|
|