| 1. |
- Murari, A., et al.
(author)
-
A control oriented strategy of disruption prediction to avoid the configuration collapse of tokamak reactors
- 2024
-
In: Nature Communications. - 2041-1723 .- 2041-1723. ; 15:1
-
Journal article (peer-reviewed)abstract
- The objective of thermonuclear fusion consists of producing electricity from the coalescence of light nuclei in high temperature plasmas. The most promising route to fusion envisages the confinement of such plasmas with magnetic fields, whose most studied configuration is the tokamak. Disruptions are catastrophic collapses affecting all tokamak devices and one of the main potential showstoppers on the route to a commercial reactor. In this work we report how, deploying innovative analysis methods on thousands of JET experiments covering the isotopic compositions from hydrogen to full tritium and including the major D-T campaign, the nature of the various forms of collapse is investigated in all phases of the discharges. An original approach to proximity detection has been developed, which allows determining both the probability of and the time interval remaining before an incoming disruption, with adaptive, from scratch, real time compatible techniques. The results indicate that physics based prediction and control tools can be developed, to deploy realistic strategies of disruption avoidance and prevention, meeting the requirements of the next generation of devices.
|
|
| 2. |
|
|
| 3. |
|
|
| 4. |
|
|
| 5. |
- Abel, I, et al.
(author)
-
Overview of the JET results with the ITER-like wall
- 2013
-
In: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10, s. 104002-
-
Journal article (peer-reviewed)abstract
- Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Z(eff) (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. The re-establishment of the baseline H-mode and hybrid scenarios compatible with the new wall has required an optimization of the control of metallic impurity sources and heat loads. Stable type-I ELMy H-mode regimes with H-98,H-y2 close to 1 and beta(N) similar to 1.6 have been achieved using gas injection. ELM frequency is a key factor for the control of the metallic impurity accumulation. Pedestal temperatures tend to be lower with the new wall, leading to reduced confinement, but nitrogen seeding restores high pedestal temperatures and confinement. Compared with the carbon wall, major disruptions with the new wall show a lower radiated power and a slower current quench. The higher heat loads on Be wall plasma-facing components due to lower radiation made the routine use of massive gas injection for disruption mitigation essential.
|
|
| 6. |
- Romanelli, F, et al.
(author)
-
Overview of the JET results
- 2011
-
In: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 51:9
-
Journal article (peer-reviewed)abstract
- Since the last IAEA Conference JET has been in operation for one year with a programmatic focus on the qualification of ITER operating scenarios, the consolidation of ITER design choices and preparation for plasma operation with the ITER-like wall presently being installed in JET. Good progress has been achieved, including stationary ELMy H-mode operation at 4.5 MA. The high confinement hybrid scenario has been extended to high triangularity, lower ρ*and to pulse lengths comparable to the resistive time. The steady-state scenario has also been extended to lower ρ*and ν*and optimized to simultaneously achieve, under stationary conditions, ITER-like values of all other relevant normalized parameters. A dedicated helium campaign has allowed key aspects of plasma control and H-mode operation for the ITER non-activated phase to be evaluated. Effective sawtooth control by fast ions has been demonstrated with3He minority ICRH, a scenario with negligible minority current drive. Edge localized mode (ELM) control studies using external n = 1 and n = 2 perturbation fields have found a resonance effect in ELM frequency for specific q95values. Complete ELM suppression has, however, not been observed, even with an edge Chirikov parameter larger than 1. Pellet ELM pacing has been demonstrated and the minimum pellet size needed to trigger an ELM has been estimated. For both natural and mitigated ELMs a broadening of the divertor ELM-wetted area with increasing ELM size has been found. In disruption studies with massive gas injection up to 50% of the thermal energy could be radiated before, and 20% during, the thermal quench. Halo currents could be reduced by 60% and, using argon/deuterium and neon/deuterium gas mixtures, runaway electron generation could be avoided. Most objectives of the ITER-like ICRH antenna have been demonstrated; matching with closely packed straps, ELM resilience, scattering matrix arc detection and operation at high power density (6.2 MW m-2) and antenna strap voltages (42 kV). Coupling measurements are in very good agreement with TOPICA modelling. © 2011 IAEA, Vienna.
|
|
| 7. |
- Alberdi, A., et al.
(author)
-
Dynamic characterisation of different magneto-sensitive natural rubbers for application in vibration isolation
- 2010
-
In: Proceedings of ISMA 2010 - International Conference on Noise and Vibration Engineering, including USD 2010. - : Katholieke Universiteit Leuven. - 9789073802872 ; , s. 227-231
-
Conference paper (peer-reviewed)abstract
- Dynamic properties of magneto-sensitive natural rubber components were experimentally studied. Different magneto-sensitive rubbers were manufactured, consisting of irregularly shaped micron-sized iron particles embedded in a natural rubber matrix, and the influence of the hardness of the matrix material and the particle volume concentration were analyzed. Vibration isolators consisting of magneto-sensitive elastomers promise to have more functionality than conventional isolators as they can change their dynamic stiffness rapidly, continuously and reversibly under the application of an external magnetic field. Experimental measurements on MS components show that a better performance may be obtained at applications where small amplitudes are required, using soft matrix materials and with concentration close to a critical particle volume fraction.
|
|
| 8. |
- Alberdi-Muniain, Ane, et al.
(author)
-
An experimental study of magneto-sensitive natural rubber components applied in a vibration isolation system
- 2009
-
In: CONSTITUTIVE MODELS FOR RUBBER VI. - London : Taylor & Francis. - 9780415563277 ; , s. 99-104
-
Conference paper (peer-reviewed)abstract
- The effectiveness of magneto-sensitive natural rubber components applied in a vibration isolation system is experimentally investigated, where influences of excitation position, amplitude, frequency and magnetic field are examined. The magneto-sensitive elastomer consists of micron-sized, irregularly shaped iron particles blended in soft natural rubber at a concentration close to the critical particle volume fraction, shown to be the most favorable composition for optimum behaviour. A rigid aluminium mass supported on four vibration isolators is excited by an electro-dynamic shaker. Each component of this vibration isolation system is composed of two thin, square shaped, symmetrically positioned magneto-sensitive elements excited in simple shear with a magnetic field applied perpendicularly to the motion by an electromagnet. The magnetic field is varied by applying different intensities through the coil. The excitation position is either on the centre or on the edge of the surface of the mass, using step-sine excitation of various amplitudes in the frequency range of 0 to 300 Hz. The results show that it is possible to use magneto-sensitive rubber for vibration control purposes.
|
|
| 9. |
- Alberdi-Muniain, Ane, et al.
(author)
-
Direct energy flow measurement in magneto-sensitive vibration isolator systems
- 2012
-
In: Journal of Sound and Vibration. - : Elsevier. - 0022-460X .- 1095-8568. ; 331:9, s. 1994-2006
-
Journal article (peer-reviewed)abstract
- The effectiveness of highly nonlinear, frequency, amplitude and magnetic field dependent magneto-sensitive natural rubber components applied in a vibration isolation system is experimentally investigated by measuring the energy flow into the foundation. The energy flow, including both force and velocity of the foundation, is a suitable measure of the effectiveness of a real vibration isolation system where the foundation is not perfectly rigid. The vibration isolation system in this study consists of a solid aluminium mass supported on four magneto-sensitive rubber components and is excited by an electro-dynamic shaker while applying various excitation signals, amplitudes and positions in the frequency range of 20-200 Hz and using magneto-sensitive components at zero-field and at magnetic saturation. The energy flow through the magneto-sensitive rubber isolators is directly measured by inserting a force transducer below each isolator and an accelerometer on the foundation close to each isolator. This investigation provides novel practical insights into the potential of using magneto-sensitive material isolators in noise and vibration control, including their advantages compared to traditional vibration isolators. Finally, nonlinear features of magneto-sensitive components are experimentally verified.
|
|
| 10. |
- Alberdi-Muniain, Ane, et al.
(author)
-
Indirect energy flow measurement in magneto-sensitive vibration isolator systems
- 2013
-
In: Applied Acoustics. - : Elsevier BV. - 0003-682X .- 1872-910X. ; 74:4, s. 575-584
-
Journal article (other academic/artistic)abstract
- The indirect energy flow measurement method is extended to cover highly nonlinear, frequency, amplitude and magnetic field dependent magneto-sensitive natural rubber isolators applied in a real vibration isolation system. Energy flow is an effective measure of vibration isolation while being a single quantity that considers both force and velocity. The use of the indirect technique is of interest while requiring only accelerometers since it is usually difficult to directly measure the force in a real application. The vibration isolation system is composed of four magneto-sensitive rubber isolators that are inserted under a vibrating source consisting of a solid aluminium mass excited by an electro-dynamic shaker. Magneto-sensitive rubber isolators are more useful than conventional rubber isolators since the dynamic stiffness varies with the application of an external magnetic field, thus resulting in more effective vibration isolation. Various approximations regarding the indirect technique are investigated, concluding that average stiffness of magneto-sensitive isolators can be used and auto-spectrum of the foundation velocity ignored. In addition, various error analyses are performed. Finally, the indirect measurement of the energy flow is validated by direct measurements, showing very good agreement.
|
|
