| 1. |
- Zhang, Pimin, 1990-, et al.
(author)
-
Effects of surface finish on the initial oxidation of HVAF-sprayed NiCoCrAlY coatings
- 2019
-
In: Surface & Coatings Technology. - Elsevier : Elsevier BV. - 0257-8972 .- 1879-3347. ; 364, s. 43-56
-
Journal article (peer-reviewed)abstract
- Oxide scale formed on HVAF-sprayed NiCoCrAlY coatings and the effect of surface treatment were investigated by a multi-approach study combining photo-stimulated luminescence, microstructural observation and mass gain. The initial oxidationbehaviour of as-sprayed, polished and shot-peened coatings at 1000 °C is studied. Both polished and shot-peened coatings exhibited superior performance due to rapid formation of α-Al2O3 fully covering the coating and suppressing the growth of transient alumina, assisted by a high density of α-Al2O3 nuclei on surface treatment induced defects. Moreover, the fast development of a two-layer alumina scale consisting of an inward-grown inner α-Al2O3 layer and an outer layer transformed from outward-grown transient alumina resulted in a higher oxide growth rate of the as-sprayed coating.
|
|
| 2. |
- Ganvir, Ashish, 1991-, et al.
(author)
-
A Facile Approach to Deposit Graphenaceous Composite Coatings by Suspension Plasma Spraying
- 2019
-
In: Coatings. - : MDPI AG. - 2079-6412. ; 9:3
-
Journal article (peer-reviewed)abstract
- This paper demonstrates, for the first time ever, the deposition of graphenaceous composite coatings using an easy, yet robust, suspension plasma spraying (SPS) process. As a case study, a composite coating comprising 8 wt.% of yttria-stabilized-zirconia (8YSZ) and reinforced with graphene oxide (GO) was deposited on a steel substrate. The coatings were sprayed using an 8YSZ-GO mixed suspension with varied plasma spray parameters. Establishing the possibility of retaining the graphene in a ceramic matrix using SPS was of specific interest. Electron microscopy and Raman spectroscopy confirmed the presence of graphenaceous material distributed throughout the coating in the 8YSZ matrix. The experimental results discussed in this work confirm that SPS is an immensely attractive pathway to incorporate a graphenaceous material into virtually any matrix material and can potentially have major implications in enabling the deposition of large-area graphene-containing coatings for diverse functional applications.
|
|
| 3. |
- Ganvir, Ashish, 1991-, et al.
(author)
-
Influence of Microstructure on Thermal Properties of Axial Suspension Plasma-Sprayed YSZ Thermal Barrier Coatings
- 2016
-
In: Journal of thermal spray technology (Print). - : Springer Science and Business Media LLC. - 1059-9630 .- 1544-1016. ; 25:1-2, s. 202-212
-
Journal article (peer-reviewed)abstract
- Suspension plasma spraying is a relatively new thermal spaying technique to produce advanced thermal barrier coatings (TBCs) and enables production of coatings with a variety of structures—highly dense, highly porous, segmented, or columnar. This work investigates suspension plasma-sprayed TBCs produced using axial injection with different process parameters. The influence of coating microstructure on thermal properties was of specific interest. Tests carried out included microstructural analysis, phase analysis, determination of porosity, and pore size distribution, as well as thermal diffusivity/conductivity measurements. Results showed that axial suspension plasma spraying process makes it possible to produce various columnar-type coatings under different processing conditions. Significant influence of microstructural features on thermal properties of the coatings was noted. In particular, the process parameter-dependent microstructural attributes, such as porosity, column density, and crystallite size, were shown to govern the thermal diffusivity and thermal conductivity of the coating.
|
|
| 4. |
- Joshi, Shrikant V., 1960-, et al.
(author)
-
Advanced Coatings by Thermal Spray Processes
- 2019
-
In: Technologies. - : MDPI. - 2227-7080. ; 7:4, s. 1-14
-
Journal article (peer-reviewed)abstract
- Coatings are pivotal in combating problems of premature component degradation in aggressive industrial environments and constitute a strategic area for continued development. Thermal spray (TS) coatings offer distinct advantages by combining versatility, cost-effectiveness, and the ability to coat complex geometries without constraints of other in-chamber processes. Consequently, TS techniques like high-velocity oxy-fuel (HVOF) and atmospheric plasma spray (APS) are industrially well-accepted. However, they have reached limits of their capabilities while expectations from coatings progressively increase in pursuit of enhanced efficiency and productivity. Two emerging TS variants, namely high-velocity air-fuel (HVAF) and liquid feedstock thermal spraying, offer attractive pathways to realize high-performance surfaces superior to those hitherto achievable. Supersonic HVAF spraying provides highly adherent coatings with negligible porosity and its low processing temperature also ensures insignificant thermal ‘damage’ (oxidation, decarburization, etc.) to the starting material. On the other hand, liquid feedstock derived TS coatings, deposited using suspensions of fine particles (100 nm–5 µm) or solution precursors, permits the production of coatings with novel microstructures and diverse application-specific architectures. The possibility of hybrid processing, combining liquid and powder feedstock, provides further opportunities to fine tune the properties of functional surfaces. These new approaches are discussed along with some illustrative examples.
|
|
| 5. |
- Joshi, Shrikant V., 1960-, et al.
(author)
-
New Generation Ceramic Coatings for High-Temperature Applications by Liquid Feedstock Plasma Spraying : Defense, Security, Aerospace and Energy Applications
- 2020
-
In: Handbook of Advanced Ceramics and Composites. - Cham : Springer. - 9783319732558 ; , s. 1-42
-
Book chapter (other academic/artistic)abstract
- Plasma spraying with liquid feedstock offers an exciting opportunity to obtain coatings with characteristics that are vastly different from those produced using conventional spray-grade powders. The two extensively investigated variants of this technique are suspension plasma spraying (SPS), which utilizes a suspension of fine powders in an appropriate medium, and solution precursor plasma spraying (SPPS), which involves use of a suitable solution precursor that can form the desired particles in situ. The advent of axial injection plasma spray systems in recent times has also eliminated concerns regarding low deposition rates/efficiencies associated with liquid feedstock. The 10–100 μm size particles that constitute conventional spray powders lead to individual splats that are more than an order of magnitude larger compared to those resulting from the fine (approximately 100 nm–2 μm in size) particles already present in suspensions in SPS or formed in situ in SPPS. The distinct characteristics of the resulting coatings are directly attributable to the above very dissimilar splats (“building blocks” for coatings) responsible for their formation. This chapter discusses the salient features associated with SPS and SPPS processing, highlights their versatility for depositing a vast range of ceramic coatings with diverse functional attributes, and discusses their utility, particularly for high-temperature applications through some illustrative examples. A further extension of liquid feedstock plasma processing to enable use of hybrid powder-liquid combinations for plasma spraying is also discussed. This presents a novel approach to explore new material combinations, create various function-dependent coating architectures with multi-scale features, and enable convenient realization of layered, composite, and graded coatings as demonstrated through specific examples.
|
|
| 6. |
- Kumara, Chamara, et al.
(author)
-
Microstructure modelling of laser metal powder directed energy deposition of alloy 718
- 2019
-
In: Additive Manufacturing. - : Elsevier. - 2214-8604 .- 2214-7810. ; 25, s. 357-364
-
Journal article (peer-reviewed)abstract
- A multi-component and multi-phase-field modelling approach, combined with transformation kinetics modelling, was used to model microstructure evolution during laser metal powder directed energy deposition of Alloy 718 and subsequent heat treatments. Experimental temperature measurements were utilised to predict microstructural evolution during successive addition of layers. Segregation of alloying elements as well as formation of Laves and δ phase was specifically modelled. The predicted elemental concentrations were then used in transformation kinetics to estimate changes in Continuous Cooling Transformation (CCT) and Time Temperature Transformation (TTT) diagrams for Alloy 718. Modelling results showed good agreement with experimentally observed phase evolution within the microstructure. The results indicate that the approach can be a valuable tool, both for improving process understanding and for process development including subsequent heat treatment.
|
|
| 7. |
- Markocsan, Nicolaie, 1967-, et al.
(author)
-
Liquid Feedstock Plasma Spraying : An Emerging Process for Advanced Thermal Barrier Coatings
- 2017
-
In: Journal of thermal spray technology (Print). - : Springer Science and Business Media LLC. - 1059-9630 .- 1544-1016. ; 26:6, s. 1104-1114
-
Journal article (peer-reviewed)abstract
- Liquid feedstock plasma spraying (LFPS) involves deposition of ultrafine droplets of suspensions or solution precursors (typically ranging from nano- to submicron size) and permits production of coatings with unique microstructures that are promising for advanced thermal barrier coating (TBC) applications. This paper reviews the recent progress arising from efforts devoted to development of high-performance TBCs using the LFPS approach. Advancements in both suspension plasma spraying and solution precursor plasma spraying, which constitute the two main variants of LFPS, are presented. Results illustrating the different types of the microstructures that can be realized in LFPS through appropriate process parameter control, model-assisted assessment of influence of coating defects on thermo-mechanical properties and the complex interplay between pore coarsening, sintering and crystallite growth in governing thermal conductivity are summarized. The enhancement in functional performances/lifetime possible in LFPS TBCs with multilayered architectures and by incorporating new pyrochlore chemistries such as gadolinium zirconate, besides the conventional single 8 wt.% yttria-stabilized zirconia insulating ceramic layer, is specifically highlighted.
|
|
| 8. |
- Sreekanth, Suhas, et al.
(author)
-
Effect of Direct Energy Deposition Process Parameters on Single-Track Deposits of Alloy 718
- 2020
-
In: Metals. - : MDPI AG. - 2075-4701. ; 10:1, s. 01-16
-
Journal article (peer-reviewed)abstract
- The effect of three important process parameters, namely laser power, scanning speed and laser stand-off distance on the deposit geometry, microstructure and segregation characteristics in direct energy deposited alloy 718 specimens has been studied. Laser power and laser stand-off distance were found to notably affect the width and depth of the deposit, while the scanning speed influenced the deposit height. An increase in specific energy conditions (between 0.5 J/mm2 and 1.0 J/mm2) increased the total area of deposit yielding varied grain morphologies and precipitation behaviors which were comprehensively analyzed. A deposit comprising three distinct zones, namely the top, middle and bottom regions, categorized based on the distinct microstructural features formed on account of variation in local solidification conditions. Nb-rich eutectics preferentially segregated in the top region of the deposit (5.4–9.6% area fraction, Af) which predominantly consisted of an equiaxed grain structure, as compared to the middle (1.5–5.7% Af) and the bottom regions (2.6–4.5% Af), where columnar dendritic morphology was observed. High scan speed was more effective in reducing the area fraction of Nb-rich phases in the top and middle regions of the deposit. The <100> crystallographic direction was observed to be the preferred growth direction of columnar grains while equiaxed grains had a random orientation.
|
|
| 9. |
- Sreekanth, Suhas, et al.
(author)
-
Effect of process parameters and heat treatments on delta-phase precipitation in directed energy deposited alloy 718
- 2022
-
In: Welding in the World. - : Springer. - 0043-2288 .- 1878-6669.
-
Journal article (peer-reviewed)abstract
- This article outlines a detailed study of solution treatments and delta precipitation treatments carried out on laser-directed energy deposited (DED) alloy 718 specimens. Two different sets of DED process parameters were used in high and low energy conditions that yield different microstructural features to study the effect of process parameters on delta precipitation. These two conditions were subjected to solution treatment at 1010 °C and 1050 °C each for 1 h, which improved homogeneity and altered grain texture with introduction of annealing twins. The as-built and solution-treated specimens served as the initial reference condition for subsequent delta processing treatments (DPT) performed at three temperatures of 850 °C, 900 °C, and 950 °C to study the effect of short- and long-term exposures ranging from 1 to 48 h. When as-built specimens were subjected to DPT, interdendritic delta precipitates were observed at Nb-rich regions. In contrast, solution-treated specimens under short-term exposure to DPT resulted in intergranular delta phase precipitates whereas under long-term exposures to DPT yielded predominantly intragranular delta precipitates, which grew denser and longer with increased time of treatment. For longer exposure times of 24 and 48 h, a continuous film of intergranular delta phase was noticed. The morphology, location, and volume fraction of delta phase precipitates studied in this research are imperative for designing the performance of alloy 718 built by DED process.
|
|
| 10. |
- Sreekanth, Suhas, et al.
(author)
-
Influence of laser-directed energy deposition process parameters and thermal post-treatments on Nb-rich secondary phases in single-track Alloy 718 specimens
- 2021
-
In: Journal of laser applications. - : Laser Institute of America. - 1042-346X .- 1938-1387. ; 33:2, s. 1-13
-
Journal article (peer-reviewed)abstract
- In this article, process parameters such as laser power, deposition speed, and powder feed rate are varied at three levels, and their effect on geometrical characteristics and microstructural features of laser-direct energy deposited single-track Alloy 718 specimens is analyzed. Furthermore, the influence of standard heat treatments recommended for wrought form of Alloy 718 is investigated on as-built deposits. The main aim of the research is to curtail the amount of secondary Nb-rich precipitates such as Laves and NbCs either during the process or by subsequent heat treatments. The volume fraction analysis of Nb-rich phases shows that processing at high laser power conditions is ideal for minimizing segregation. Upon subjecting as-built deposits to (i) solution treatment, (ii) solution treatment and aging, and (iii) direct aging, a difference in volume fraction of Nb-rich phases is noticed compared to the as-built condition. Characterization of size, morphology, phase constitution through volume fraction estimation, and elemental concentrations employing electron dispersive spectroscopy analysis indicates dissolution of Nb-rich phases when subjected to heat treatments. The delta phase precipitation preferentially occurs in the top and bottom regions and sparsely in the middle region of the specimens subjected to solution heat treatment. In case of specimens subjected to direct aging (718 °C/8 h and 621 °C/8 h), delta phase is not discernable, indicating that a higher temperature (>900 °C) treatment may be necessary for delta precipitation and growth
|
|
