1. |
- Ngoc Pham, Tung, et al.
(author)
-
Industrially benign super-compressible piezoresistive carbon foams with predefined wetting properties : from environmental to electrical applications
- 2014
-
In: Scientific Reports. - : Nature Publishing Group. - 2045-2322. ; 4
-
Journal article (peer-reviewed)abstract
- In the present work electrically conductive, flexible, lightweight carbon sponge materials derived from open-pore structure melamine foams are studied and explored. Hydrophobic and hydrophilic surface properties - depending on the chosen treatment conditions - allow the separation and storage of liquid chemical compounds. Activation of the carbonaceous structures substantially increases the specific surface area from ,4 m2 g21 to ,345 m2 g21 , while retaining the original three-dimensional, open-pore structure suitable for hosting, for example, Ni catalyst nanoparticles. In turn the structure is rendered suitable for hydrogenating acetone to 2-propanol and methyl isobutyl ketone as well for growing hierarchical carbon nanotube structures used as electric double-layer capacitor electrodes with specific capacitance of ,40 F/g. Mechanical stress-strain analysis indicates the materials are super-compressible (.70% volume reduction) and viscoelastic with excellent damping behavior (loss of 0.69 6 0.07), while piezoresistive measurements show very high gauge factors (from ,20 to 50) over a large range of deformations. The cost-effective, robust and scalable synthesis - in conjunction with their fascinating multifunctional utility - makes the demonstrated carbon foams remarkable competitors with other three-dimensional carbon materials typically based on pyrolyzed biopolymers or on covalently bonded graphene and carbon nanotube frameworks.
|
|
2. |
- Aldea, Steliana, et al.
(author)
-
Crystallization of Nano-Calcium Carbonate : The Influence of Process Parameters
- 2016
-
In: Chemie Ingenieur Technik. - : Wiley-VCH Verlagsgesellschaft. - 0009-286X .- 1522-2640. ; 88:11, s. 1609-1616
-
Journal article (peer-reviewed)abstract
- Precipitated calcium carbonate was synthesized by carbonation of calcium hydroxide in the presence and absence of ultrasound (conventional stirring) at atmospheric as well as at elevated pressures and different initial concentrations of Ca(OH)2. Spherical morphology of the formed calcite was favored at high Ca(OH)2 concentrations and low CO2 pressures. The presence of ultrasound did not show any influence on the reaction rate in case of efficient mixing. A small increase of the reaction rate was observed at lower CO2 pressures. Elevated pressures in combination with ultrasound did not lead to notable changes of reaction rate or particle morphology.
|
|
3. |
- Alene Asres, Georgies, et al.
(author)
-
A novel WS2 nanowire-nanoflake hybrid material synthesized from WO3 nanowires in sulfur vapor
- 2016
-
In: Scientific Reports. - : NATURE PUBLISHING GROUP. - 2045-2322. ; 6:25610
-
Journal article (peer-reviewed)abstract
- In this work, WS2 nanowire-nanoflake hybrids are synthesized by the sulfurization of hydrothermally grown WO3 nanowires. The influence of temperature on the formation of products is optimized to grow WS2 nanowires covered with nanoflakes. Current-voltage and resistance-temperature measurements carried out on random networks of the nanostructures show nonlinear characteristics and negative temperature coefficient of resistance indicating that the hybrids are of semiconducting nature. Bottom gated field effect transistor structures based on random networks of the hybrids show only minor modulation of the channel conductance upon applied gate voltage, which indicates poor electrical transport between the nanowires in the random films. On the other hand, the photo response of channel current holds promise for cost-efficient solution process fabrication of photodetector devices working in the visible spectral range.
|
|
4. |
- Asres, Georgies Alene, et al.
(author)
-
High photoresponse of individual WS2 nanowire-nanoflake hybrid materials
- 2018
-
In: Applied Physics Letters. - : AMER INST PHYSICS. - 0003-6951 .- 1077-3118. ; 112:23
-
Journal article (peer-reviewed)abstract
- van der Waals solids have been recognized as highly photosensitive materials that compete conventional Si and compound semiconductor based devices. While 2-dimensional nanosheets of single and multiple layers and 1-dimensional nanowires of molybdenum and tungsten chalcogenides have been studied, their nanostructured derivatives with complex morphologies are not explored yet. Here, we report on the electrical and photosensitive properties of WS2 nanowire-nanoflake hybrid materials we developed lately. We probe individual hybrid nanostructured particles along the structure using focused ion beam deposited Pt contacts. Further, we use conductive atomic force microscopy to analyze electrical behavior across the nanostructure in the transverse direction. The electrical measurements are complemented by in situ laser beam illumination to explore the photoresponse of the nanohybrids in the visible optical spectrum. Photodetectors with responsivity up to similar to 0.4 AW(-1) are demonstrated outperforming graphene as well as most of the other transition metal dichalcogenide based devices. Published by AIP Publishing.
|
|
5. |
- Asres, Georgies Alene, et al.
(author)
-
Ultrasensitive H2S gas sensors based on p-type WS2 hybrid materials
- 2018
-
In: Nano Reseach. - : Springer. - 1998-0124 .- 1998-0000. ; 11:8, s. 4215-4224
-
Journal article (peer-reviewed)abstract
- Owing to their higher intrinsic electrical conductivity and chemical stability with respect to their oxide counterparts, nanostructured metal sulfides are expected to revive materials for resistive chemical sensor applications. Herein, we explore the gas sensing behavior of WS2 nanowire-nanoflake hybrid materials and demonstrate their excellent sensitivity (0.043 ppm-1) as well as high selectivity towards H2S relative to CO, NH3, H2, and NO (with corresponding sensitivities of 0.002, 0.0074, 0.0002, and 0.0046 ppm-1, respectively). Gas response measurements, complemented with the results of X-ray photoelectron spectroscopy analysis and first-principles calculations based on density functional theory, suggest that the intrinsic electronic properties of pristine WS2 alone are not sufficient to explain the observed high sensitivity towards H2S. A major role in this behavior is also played by O doping in the S sites of the WS2 lattice. The results of the present study open up new avenues for the use of transition metal disulfide nanomaterials as effective alternatives to metal oxides in future applications for industrial process control, security, and health and environmental safety.
|
|
6. |
- Bourajoini, Hasna, et al.
(author)
-
Calcium manganese oxide catalysts for water oxidation : Unravelling the influence of various synthesis strategies
- 2016
-
In: Materials research bulletin. - : Elsevier. - 0025-5408 .- 1873-4227. ; 79, s. 133-137
-
Journal article (peer-reviewed)abstract
- Abstract Three different mixed oxide catalysts primarily consisting of calcium and manganese oxides targeting artificial photosynthesis were synthesized and studied. According to the results, their catalytic activity for water oxidation was enhanced by the presence of mixed valence states of Mnn+ ions (3.0 ≤ n ≪ 4.0), while the specific surface area had negligible effect.
|
|
7. |
- Bukhanko, Natalia, et al.
(author)
-
Continuous gas phase synthesis of 1-ethyl chloride from ethyl alcohol and hydrochloric acid over Al2O3-based catalysts: the ‘green’ route
- 2013
-
In: ACS Sustainable Chemistry and Engineering. - : American Chemical Society (ACS). - 2168-0485. ; 1:8, s. 883-893
-
Journal article (peer-reviewed)abstract
- The synthesis of 1-ethyl chloride in the gas-phase mixture of ethanol and hydrochloric acid over ZnCl2/Al2O3 catalysts was studied in a continuous reactor using both commercial and tailor-made supports. The catalytic materials were characterized by the means of structural (XPS, TEM, XRD, and BET) and catalytic activity (selectivity and conversion) measurements. The reaction parameters such as temperature, pressure, and feedstock flow rates were optimized for the conversion of ethanol to ethyl chloride. The new tailor-made highly porous Al2O3-based catalyst outperformed its commercial counterpart by exhibiting high conversion and selectivity (98%) at the temperature of 325 °C. Long-term stability tests (240 h) confirmed the excellent durability of the tailor-made alumina catalysts. The process demonstrated here poses an efficient and economic “green” large-scale on-site synthesis of this industrially important reactant in industry, where bioethanol is produced and 1-ethyl chloride is necessary, e.g., for ethylation of cellulose and synthetic polymer products. On-site in situ production of ethyl chloride avoids the problems associated with the transportation and storage of toxic and flammable 1-ethyl chloride.
|
|
8. |
- Bukhanko, Natalia, et al.
(author)
-
Gas phase synthesis of isopropyl chloride from isopropanol and HCl over alumina and flexible 3-D carbon foam supported catalysts
- 2017
-
In: Applied Catalysis A. - : Elsevier. - 0926-860X .- 1873-3875. ; 542:25, s. 212-225
-
Journal article (peer-reviewed)abstract
- Isopropyl chloride synthesis from isopropanol and HCl in gas phase over ZnCl2 catalysts supported on Al2O3 as well as flexible carbon foam was studied in a continuous reactor. A series of catalytic materials were synthesised and characterised by BET, XPS, SEM, TEM, XRD and NH3-TPD methods. Catalytic activity tests (product selectivity and conversion of reactants) were performed for all materials and optimal reaction conditions (temperature and feedstock flow rates) were found. The results indicate that the highest yield of isopropyl chloride was obtained over 5 wt.% ZnCl2 on commercial Al2O3 (No. II) (95.3%). Determination of product mixture compositions and by-product identification were done using a GC-MS method. Carbon foam variant catalyst, 5 wt.% ZnCl2/C, was found to perform best out of the carbon-supported materials, achieving ∼75% yield of isopropyl chloride. The kinetic model describing the process in a continuous packed bed reactor was proposed and kinetic parameters were calculated. The activation energy for the formation of isopropyl chloride reaction directly from isopropanol and HCl was found to be ∼58 kJ/mol.
|
|
9. |
-
Dehydroisomerization of α-pinene over metal supported Si-SBA-15 mesoporous molecular sieves
- 2013
-
Editorial proceedings (peer-reviewed)abstract
- The effective dispersion of active metal species on mesoporous Si-SBA-15 is acquired by means of deposition-precipitation method. In order to achieve this, the surface of Si-SBA-15 was first modified with TiO2 via grafting method, followed by deposition-precipitation method (DP) to obtain a fine dispersion of metallic nanoparticles over TiO2 modified Si-SBA-15. The structural features of the synthesized materials were characterized by means of X-ray diffraction (XRD), nitrogen sorption (BET), XPS and HR-TEM. A valuable platform chemical, p-cymene, was produced over the prepared catalyst by dehydroisomerization of α-pinene under vapour-phase conditions. A stable catalyst for one-spot synthesis of renewable p-cymene from α-pinene was developed.
|
|
10. |
- Eta, Valerie, et al.
(author)
-
Synthesis of dimethyl carbonate from methanol and carbon dioxide : Circumventing thermodynamic limitations
- 2010
-
In: Industrial & Engineering Chemistry Research. - : American Chemical Society. - 0888-5885 .- 1520-5045. ; 49:20, s. 9609-17
-
Journal article (peer-reviewed)abstract
- The synthesis of dimethyl carbonate from methanol and CO2 catalyzed by ZrO2 doped with KCl was investigated using chemical traps for water to circumvent thermodynamic limitations. The reaction, promoted by magnesium, occurred via the formation of carbonated magnesium methoxide (CMM) which adsorbed on the surface of ZrO2. The surface migration of the oxygen atom of ZrO2 to the surface methoxy groups of CMM resulted in the formation of dimethyl carbonate. The resulting MgO then reacted with methanol forming water and regenerating magnesium methoxide. The water formed reacted with the dehydrating agent, thus shifting the equilibrium toward a higher yield of DMC. The yield of 7.2 mol % DMC and 13.6 mol % conversion of methanol was obtained when methanol reacted with CO2 at 150 °C and 9.5 MPa for 8 h. The plausible reaction pathway is described.
|
|