| 1. |
- Fan, Qunping, 1989, et al.
(författare)
-
Over 14% efficiency all-polymer solar cells enabled by a low bandgap polymer acceptor with low energy loss and efficient charge separation
- 2020
-
Ingår i: Energy & Environmental Science. - : Royal Society of Chemistry. - 1754-5692 .- 1754-5706. ; 13:12, s. 5017-5027
-
Tidskriftsartikel (refereegranskat)abstract
- Obtaining both high open-circuit voltage (V-oc) and short-circuit current density (J(sc)) has been a major challenge for efficient all-polymer solar cells (all-PSCs). Herein, we developed a polymer acceptor PF5-Y5 with excellent optical absorption capability (onset extending to similar to 880 nm and maximum absorption coefficient exceeding 105 cm(-1) in a film), high electron mobility (3.18 x 10(3) cm(2) V-1 s(-1)) and high LUMO level (-3.84 eV) to address such a challenge. As a result, the PBDB-T:PF5-Y5-based all-PSCs achieved a high power conversion efficiency of up to 14.45% with both a high Voc (0.946 V) and a high Jsc (20.65 mA cm(-2)), due to the high and broad absorption coverage, small energy loss (0.57 eV) and efficient charge separation and transport in the device, which are among the best values in the all-PSC field. In addition, the all-PSC shows a similar to 15% improvement in PCE compared to its counterpart small molecule acceptor (Y5)-based device. Our results suggest that PF5-Y5 is a very promising polymer acceptor candidate for applications in efficient all-PSCs.
|
|
| 2. |
- Firdaus, Yuliar, et al.
(författare)
-
Novel wide-bandgap non-fullerene acceptors for efficient tandem organic solar cells
- 2020
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry (RSC). - 2050-7488 .- 2050-7496. ; 8:3, s. 1164-1175
-
Tidskriftsartikel (refereegranskat)abstract
- The power conversion efficiency (PCE) of tandem organic photovoltaics (OPVs) is currently limited by the lack of suitable wide-bandgap materials for the front-cell. Here, two new acceptor molecules, namely IDTA and IDTTA, with optical bandgaps (Eoptg) of 1.90 and 1.75 eV, respectively, are synthesized and studied for application in OPVs. When PBDB-T is used as the donor polymer, single-junction cells with PCE of 7.4%, for IDTA, and 10.8%, for IDTTA, are demonstrated. The latter value is the highest PCE reported to date for wide-bandgap (Eoptg ≥ 1.7 eV) bulk-heterojunction OPV cells. The higher carrier mobility in IDTTA-based cells leads to improved charge extraction and higher fill-factor than IDTA-based devices. Moreover, IDTTA-based OPVs show significantly improved shelf-lifetime and thermal stability, both critical for any practical applications. With the aid of optical-electrical device modelling, we combined PBDB-T:IDTTA, as the front-cell, with PTB7-Th:IEICO-4F, as the back-cell, to realize tandem OPVs with open circuit voltage of 1.66 V, short circuit current of 13.6 mA cm-2 and a PCE of 15%; in excellent agreement with our theoretical predictions. The work highlights IDTTA as a promising wide-bandgap acceptor for high-performance tandem OPVs. © 2019 The Royal Society of Chemistry.
|
|
| 3. |
- Lin, Yuanbao, et al.
(författare)
-
18.73% efficient and stable inverted organic photovoltaics featuring a hybrid hole-extraction layer
- 2023
-
Ingår i: Materials Horizons. - : Royal Society of Chemistry (RSC). - 2051-6355 .- 2051-6347. ; 10:4, s. 1292-1300
-
Tidskriftsartikel (refereegranskat)abstract
- Developing efficient and stable organic photovoltaics (OPVs) is crucial for the technology's commercial success. However, combining these key attributes remains challenging. Herein, we incorporate the small molecule 2-((3,6-dibromo-9H-carbazol-9-yl)ethyl)phosphonic acid (Br-2PACz) between the bulk-heterojunction (BHJ) and a 7 nm-thin layer of MoO3 in inverted OPVs, and study its effects on the cell performance. We find that the Br-2PACz/MoO3 hole-extraction layer (HEL) boosts the cell's power conversion efficiency (PCE) from 17.36% to 18.73% (uncertified), making them the most efficient inverted OPVs to date. The factors responsible for this improvement include enhanced charge transport, reduced carrier recombination, and favourable vertical phase separation of donor and acceptor components in the BHJ. The Br-2PACz/MoO3-based OPVs exhibit higher operational stability under continuous illumination and thermal annealing (80 degrees C). The T-80 lifetime of OPVs featuring Br-2PACz/MoO3 - taken as the time over which the cell's PCE reduces to 80% of its initial value - increases compared to MoO3-only cells from 297 to 615 h upon illumination and from 731 to 1064 h upon continuous heating. Elemental analysis of the BHJs reveals the enhanced stability to originate from the partially suppressed diffusion of Mo ions into the BHJ and the favourable distribution of the donor and acceptor components induced by the Br-2PACz.
|
|
| 4. |
- Lin, Yuanbao, et al.
(författare)
-
18.9% Efficient Organic Solar Cells Based on n-Doped Bulk-Heterojunction and Halogen-Substituted Self-Assembled Monolayers as Hole Extracting Interlayers
- 2022
-
Ingår i: Advanced Energy Materials. - : Wiley. - 1614-6840 .- 1614-6832. ; 12:45
-
Tidskriftsartikel (refereegranskat)abstract
- The influence of halogen substitutions (F, Cl, Br, and I) on the energy levels of the self-assembled hole-extracting molecule [2-(9H-Carbazol-9-yl)ethyl]phosphonic acid (2PACz), is investigated. It is found that the formation of self-assembled monolayers (SAMs) of [2-(3,6-Difluoro-9H-carbazol-9-yl)ethyl]phosphonic acid (F-2PACz), [2-(3,6-Dichloro-9H-carbazol-9-yl)ethyl]phosphonic acid (Cl-2PACz), [2-(3,6-Dibromo-9H-carbazol-9-yl)ethyl]phosphonic acid (Br-2PACz), and [2-(3,6-Diiodo-9H-carbazol-9-yl)ethyl]phosphonic acid (I-2PACz) directly on indium tin oxide (ITO) increases its work function from 4.73 eV to 5.68, 5.77, 5.82, and 5.73 eV, respectively. Combining these ITO/SAM electrodes with the ternary bulk-heterojunction (BHJ) system PM6:PM7-Si:BTP-eC9 yields organic photovoltaic (OPV) cells with power conversion efficiency (PCE) in the range of 17.7%-18.5%. OPVs featuring Cl-2PACz SAMs yield the highest PCE of 18.5%, compared to cells with F-2PACz (17.7%), Br-2PACz (18.0%), or I-2PACz (18.2%). Data analysis reveals that the enhanced performance of Cl-2PACz-based OPVs relates to the increased hole mobility, decreased interface resistance, reduced carrier recombination, and longer carrier lifetime. Furthermore, OPVs featuring Cl-2PACz show enhanced stability under continuous illumination compared to ITO/PEDOT:PSS-based cells. Remarkably, the introduction of the n-dopant benzyl viologen into the BHJ further boosted the PCE of the ITO/Cl-2PACz cells to a maximum value of 18.9%, a record-breaking value for SAM-based OPVs and on par with the best-performing OPVs reported to date.
|
|
| 5. |
- Lin, Yuanbao, et al.
(författare)
-
One-Step Blade-Coated Highly Efficient Nonfullerene Organic Solar Cells with a Self-Assembled Interfacial Layer Enabled by Solvent Vapor Annealing
- 2019
-
Ingår i: Solar RRL. - : Wiley. - 2367-198X. ; 3:8
-
Tidskriftsartikel (refereegranskat)abstract
- A pronounced enhancement of the power conversion efficiency (PCE) by 38% is achieved in one-step doctor-blade printing organic solar cells (OSCs) via a simple solvent vapor annealing (SVA) step. The organic blend composed of a donor polymer, a nonfullerene acceptor, and an interfacial layer (IL) molecular component is found to phase-separate vertically when exposed to a solvent vapor-saturated atmosphere. Remarkably, the spontaneous formation of a fine, self-organized IL between the bulk heterojunction (BHJ) layer and the indium tin oxide (ITO) electrode facilitated by SVA yields solar cells with a significantly higher PCE (11.14%) than in control devices (8.05%) without SVA and in devices (10.06%) made with the more complex two-step doctor-blade printing method. The stratified nature of the ITO/IL/BHJ/cathode is corroborated by a range of complementary characterization techniques including surface energy, cross-sectional scanning electron microscopy, grazing incidence wide angle X-ray scattering, and X-ray photoelectron spectroscopy. This study demonstrates that a spontaneously formed IL with SVA treatment combines simplicity and precision with high device performance, thus making it attractive for large-area manufacturing of next-generation OSCs.
|
|
| 6. |
- Lin, Yuanbao, et al.
(författare)
-
Printed Nonfullerene Organic Solar Cells with the Highest Efficiency of 9.5%
- 2018
-
Ingår i: Advanced Energy Materials. - : WILEY-V C H VERLAG GMBH. - 1614-6832 .- 1614-6840. ; 8:13
-
Tidskriftsartikel (refereegranskat)abstract
- The current work reports a high power conversion efficiency (PCE) of 9.54% achieved with nonfullerene organic solar cells (OSCs) based on PTB7-Th donor and 3,9-bis(2-methylene-(3-(1,1-dicyanomethylene)-indanone))-5,5,11,11-tetrakis(4-hexylphenyl)-dithieno[2,3-d:2,3-d]-s-indaceno[1,2-b:5,6-b]dithiophene) (ITIC) acceptor fabricated by doctor-blade printing, which has the highest efficiency ever reported in printed nonfullerene OSCs. Furthermore, a high PCE of 7.6% is realized in flexible large-area (2.03 cm(2)) indium tin oxide (ITO)-free doctor-bladed nonfullerene OSCs, which is higher than that (5.86%) of the spin-coated counterpart. To understand the mechanism of the performance enhancement with doctor-blade printing, the morphology, crystallinity, charge recombination, and transport of the active layers are investigated. These results suggest that the good performance of the doctor-blade OSCs is attributed to a favorable nanoscale phase separation by incorporating 0.6 vol% of 1,8-diiodooctane that prolongs the dynamic drying time of the doctor-bladed active layer and contributes to the migration of ITIC molecules in the drying process. High PCE obtained in the flexible large-area ITO-free doctor-bladed nonfullerene OSCs indicates the feasibility of doctor-blade printing in large-scale fullerene-free OSC manufacturing. For the first time, the open-circuit voltage is increased by 0.1 V when 1 vol% solvent additive is added, due to the vertical segregation of ITIC molecules during solvent evaporation.
|
|
| 7. |
- Liu, Alei, et al.
(författare)
-
Manipulate Micrometer Surface and Nanometer Bulk Phase Separation Structures in the Active Layer of Organic Solar Cells via Synergy of Ultrasonic and High-Pressure Gas Spraying
- 2019
-
Ingår i: ACS Applied Materials and Interfaces. - : AMER CHEMICAL SOC. - 1944-8244 .- 1944-8252. ; 11:11, s. 10777-10784
-
Tidskriftsartikel (refereegranskat)abstract
- For organic solar cells, the vertical and lateral micro-/nanometer-scale structure in the active layer largely determines the device performance. In this work, the surface and bulk domain size of the photoactive layer are successfully manipulated with a facile two-step spraying method, that is, an ultrathin active layer by high-pressure spraying is deliberately stacked on top of the thick active layer by ultrasonic spraying. Thus, the morphology is effectively optimized with the comprehensive study of optical and electrical characteristics, such as photon absorption, exciton dissociation efficiency, and bimolecular recombination. Moreover, the novel method can be used not only in the fullerene system but also in the nonfullerene system, demonstrating the remarkable universality through this synergy method. This work provides an easy and reliable strategy to improve photovoltaic device performance in the industrial large-area spray-coating process.
|
|
| 8. |
- Yang, Junyu, et al.
(författare)
-
Roll-to-Roll Slot-Die-Printed Polymer Solar Cells by Self-Assembly
- 2018
-
Ingår i: ACS Applied Materials and Interfaces. - : AMER CHEMICAL SOC. - 1944-8244 .- 1944-8252. ; 10:26, s. 22485-22494
-
Tidskriftsartikel (refereegranskat)abstract
- Extremely simplified one-step roll-to-roll slot-die-printed flexible indium tin oxide (ITO)-free polymer solar cells (PSCs) are demonstrated based on the ternary blends of electron-donor polymer thieno[3,4-b]thiophene/benzodithiophene, electron-acceptor fullerene [6,6]-phenyl-C-71-butyric acid methyl ester, and electron-extracting polymer poly[(9,9-bis(3-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctylfluorene)] (PFN) at room temperature (RT) in ambient air. The flexible ITO-free PSC exhibits a comparable power conversion efficiency (PCE) with the device employing complicated two-step slot-die printing (5.29% vs 5.41%), which indicates that PFN molecules can migrate from the ternary nanocomposite toward the Ag cathode via vertical self-assembly during the one-step slot-die printing process in air. To confirm the migration of PFN, the morphology and elemental analysis as well as charge transport of different active layers are investigated by the in situ transient film drying process, transmission electron microscopy, atomic force microscopy, contact angle and surface energy, X-ray photoelectron spectroscopy, scanning electron microscopy, impedance spectroscopy, transient photovoltage and transient photocurrent, and laser-beam-induced current. Moreover, the good air and mechanical stability of the flexible device with a decent PCE achieved in 1 cm(2) PSCs at RT in air suggests the feasibility of energy-saving and time-saving one-step slot-die printing to large-scale roll-to-roll manufacture in the future.
|
|
| 9. |
- Zheng, Wenhao, et al.
(författare)
-
Dual Function of UV/Ozone Plasma-Treated Polymer in Polymer/Metal Hybrid Electrodes and Semitransparent Polymer Solar Cells
- 2017
-
Ingår i: ACS Applied Materials and Interfaces. - : AMER CHEMICAL SOC. - 1944-8244 .- 1944-8252. ; 9:51, s. 44656-44666
-
Tidskriftsartikel (refereegranskat)abstract
- In this work, high-performance inverted indium tin oxide (ITO)-free semitransparent polymer solar cells are comprehensively investigated using a novel polymer/metal hybrid transparent electrode. The electrical and optical characteristics of hybrid electrodes are significantly enhanced by introducing UV/ozone plasma treatment on the polymer poly[(9,9-bis(3-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctylfluorene)] (PFN), which is functioned as both a seed layer for ultrathin Ag metal electrode and an optical spacer for transparent devices. The optimized sheet resistance of PFN/Ag (12 nm) hybrid electrode is only half of the commercial ITO (9.4 vs 20.0 Omega sq(-1)) and the high wavelength-dependent reflectance of hybrid electrode helps to increase the ITO-free device short-circuit current density. Furthermore, the interface property between PFN and ultrathin Ag is analyzed in detail and the optical field distribution is calculated for comparison. A high power conversion efficiency of 5.02%, which is increased by 35% compared to that of the ITO-based device, is achieved in the ITO-free semitransparent device in conjunction with an excellent average visible transmittance above 28% that is higher than the benchmark of 25% for power-generating window, indicating its great potential in building integrated photovoltaic systems in the future. Furthermore, the strategy is successfully developed for other polymer systems, suggesting the universal applicability for plastic electronics.
|
|
| 10. |
- Zheng, Xiaopeng, et al.
(författare)
-
Managing grains and interfaces via ligand anchoring enables 22.3%-efficiency inverted perovskite solar cells
- 2020
-
Ingår i: NATURE ENERGY. - : Nature Publishing Group. - 2058-7546. ; 5, s. 131-140
-
Tidskriftsartikel (refereegranskat)abstract
- Inverted perovskite solar cells have attracted increasing attention because they have achieved long operating lifetimes. However, they have exhibited significantly inferior power conversion efficiencies compared to regular perovskite solar cells. Here we reduce this efficiency gap using a trace amount of surface-anchoring alkylamine ligands (AALs) with different chain lengths as grain and interface modifiers. We show that long-chain AALs added to the precursor solution suppress nonradiative carrier recombination and improve the optoelectronic properties of mixed-cation mixed-halide perovskite films. The resulting AAL surface-modified films exhibit a prominent (100) orientation and lower trap-state density as well as enhanced carrier mobilities and diffusion lengths. These translate into a certified stabilized power conversion efficiency of 22.3% (23.0% power conversion efficiency for lab-measured champion devices). The devices operate for over 1,000 h at the maximum power point under simulated AM1.5 illumination, without loss of efficiency. While perovskite solar cells with an inverted architecture hold great promise for operation stability, their power conversion efficiency lags behind that of conventional cells. Here, Zheng et al. achieve a certified 22.34% efficiency, exploiting alkylamine ligands as grain and interface modifiers.
|
|
