| 1. |
- Bhatnagar, Amit, et al.
(author)
-
Valorization of solid waste products from olive oil industry as potential adsorbents for water pollution control-a review
- 2014
-
In: Environmental Science and Pollution Research. - : Springer Science and Business Media LLC. - 0944-1344 .- 1614-7499. ; 21:1, s. 268-298
-
Research review (peer-reviewed)abstract
- The global olive oil production for 2010 is estimated to be 2,881,500 metric tons. The European Union countries produce 78.5 % of the total olive oil, which stands for an average production of 2,136,000 tons. The worldwide consumption of olive oil increased of 78 % between 1990 and 2010. The increase in olive oil production implies a proportional increase in olive mill wastes. As a consequence of such increasing trend, olive mills are facing severe environmental problems due to lack of feasible and/or cost-effective solutions to olive-mill waste management. Therefore, immediate attention is required to find a proper way of management to deal with olive mill waste materials in order to minimize environmental pollution and associated health risks. One of the interesting uses of solid wastes generated from olive mills is to convert them as inexpensive adsorbents for water pollution control. In this review paper, an extensive list of adsorbents (prepared by utilizing different types of olive mill solid waste materials) from vast literature has been compiled, and their adsorption capacities for various aquatic pollutants removal are presented. Different physicochemical methods that have been used to convert olive mill solid wastes into efficient adsorbents have also been discussed. Characterization of olive-based adsorbents and adsorption mechanisms of various aquatic pollutants on these developed olive-based adsorbents have also been discussed in detail. Conclusions have been drawn from the literature reviewed, and suggestions for future research are proposed.
|
|
| 2. |
- Carvalho, Joao, et al.
(author)
-
A drill-hole, geological and geophysical data-based 3D model for target generation in Neves-Corvo mine region, Portugal
- 2022
-
In: International journal of earth sciences. - : Springer Nature. - 1437-3254 .- 1437-3262. ; 111, s. 403-424
-
Journal article (peer-reviewed)abstract
- The Neves-Corvo world class Iberian Pyrite Belt volcanogenic massive sulphide (VMS) deposit located in southern Portugal, constitutes an important Cu-Zn-Pb active mine. Seven deposits are currently known, among which the Lombador deposit alone has estimated 150 Mt of massive sulphides. The life-time of the mine is dependent on the discovery of new exploration targets and it is vital to have accurate 3D geological models, not only to guide drilling campaigns but also to drive a winning/new strategy, which in the past has led to Semblana and Monte Branco discoveries: geophysical inversion and modelling. Furthermore, 3D geological models can contribute to the understanding of the tectonic and stratigraphic evolution of the region. Therefore, the goal of this study is to produce a realistic 3D geological model of the Neves-Corvo region, as only one model is presently publicly available: the PROMINE model, which includes the study area of this work and extends from Aljustrel to the border with Spain. Lundin Mining has also produced two unpublished, confidential models in 2007 and 2017. The latest Lundin model incorporates the same geophysical data used in this work (2D and 3D seismic reflection and time-domain electromagnetic (TEM) ground loop data) and approximately 7500 surface and underground drill-holes. The model presented in this research has much more detail than the 2012 PROMINE model in the Neves-Corvo region and uses an updated and revised drill-hole database with approximately 8000 drill-holes, revised geological cross-sections built from surface geology and drill-hole logs, new geological outcrop data, petrophysical and reprocessed geophysical data, and is therefore more detailed and accurate than any of the previous models, in particular the 2007 and PROMINE models. Land gravimetric and aeromagnetic data are also available in the study area but were not directly used to build the geological model but rather to investigate and check the model produced. Modelling was performed with industry standard software and the 3D curves resulting from the geological/geophysical interpretation were interpolated using different approaches to respect the hard data (interpretation lines and drill-holes). The resulting 3D stratigraphic surfaces required strong manual editing to respect the interpretation, due to the presence of folds, thrusts and tectonic nappes in the study area. The surfaces were afterwards tied to the drill-holes, resulting in a 3D model with great accuracy and detail in the near mining area and covering a larger area than previously available 3D geological models. The model has three major stratigraphic layers: the Mertola Flysch Formation and the Volcano-Sedimentary Complex (VSC), overlying the Phyllite-Quartzite Formation basement, and also the known VMS deposits (underlying the top of the Lower VSC) geometries according to drill-hole data. In the central part of the study area, where more drill-holes are available, the top of the Lower VSC sequence surface was also built. This approach will contribute to a better exploration drill-hole planning and the generation of new targets for exploration.
|
|
| 3. |
- Coelho, Teresa, et al.
(author)
-
Eplontersen for Hereditary Transthyretin Amyloidosis with Polyneuropathy
- 2023
-
In: Journal of the American Medical Association (JAMA). - : American Medical Association (AMA). - 0098-7484 .- 1538-3598. ; 330:15, s. 1448-1458
-
Journal article (peer-reviewed)abstract
- Importance: Transthyretin gene silencing is an emerging treatment strategy for hereditary transthyretin (ATTRv) amyloidosis.Objective: To evaluate eplontersen, an investigational ligand-conjugated antisense oligonucleotide, in ATTRv polyneuropathy.Design, Setting, and Participants: NEURO-TTRansform was an open-label, single-group, phase 3 trial conducted at 40 sites across 15 countries (December 2019-April 2023) in 168 adults with Coutinho stage 1 or 2 ATTRv polyneuropathy, Neuropathy Impairment Score 10-130, and a documented TTR variant. Patients treated with placebo from NEURO-TTR (NCT01737398; March 2013-November 2017), an inotersen trial with similar eligibility criteria and end points, served as a historical placebo ("placebo") group.Interventions: Subcutaneous eplontersen (45 mg every 4 weeks; n = 144); a small reference group received subcutaneous inotersen (300 mg weekly; n = 24); subcutaneous placebo weekly (in NEURO-TTR; n = 60).Main Outcomes and Measures: Primary efficacy end points at week 65/66 were changes from baseline in serum transthyretin concentration, modified Neuropathy Impairment Score +7 (mNIS+7) composite score (scoring range, -22.3 to 346.3; higher scores indicate poorer function), and Norfolk Quality of Life Questionnaire-Diabetic Neuropathy (Norfolk QoL-DN) total score (scoring range, -4 to 136; higher scores indicate poorer quality of life). Analyses of efficacy end points were based on a mixed-effects model with repeated measures adjusted by propensity score weights.Results: Among 144 eplontersen-treated patients (mean age, 53.0 years; 69% male), 136 (94.4%) completed week-66 follow-up; among 60 placebo patients (mean age, 59.5 years; 68% male), 52 (86.7%) completed week-66 follow-up. At week 65, adjusted mean percentage reduction in serum transthyretin was -81.7% with eplontersen and -11.2% with placebo (difference, -70.4% [95% CI, -75.2% to -65.7%]; P <.001). Adjusted mean change from baseline to week 66 was lower (better) with eplontersen vs placebo for mNIS+7 composite score (0.3 vs 25.1; difference, -24.8 [95% CI, -31.0 to -18.6; P <.001) and for Norfolk QoL-DN (-5.5 vs 14.2; difference, -19.7 [95% CI, -25.6 to -13.8]; P <.001). Adverse events by week 66 that led to study drug discontinuation occurred in 6 patients (4%) in the eplontersen group vs 2 (3%) in the placebo group. Through week 66, there were 2 deaths in the eplontersen group consistent with known disease-related sequelae (cardiac arrhythmia; intracerebral hemorrhage); there were no deaths in the placebo group.Conclusions and Relevance: In patients with ATTRv polyneuropathy, the eplontersen treatment group demonstrated changes consistent with significantly lowered serum transthyretin concentration, less neuropathy impairment, and better quality of life compared with a historical placebo.Trial Registration: ClinicalTrials.gov Identifier: NCT04136184; EU Clinical Trials Register: EudraCT 2019-001698-10.
|
|
| 4. |
- Dias, Pedro, et al.
(author)
-
Geophysical investigation of the down-dip extension of the Lombador massive sulphide deposit, Neves-Corvo, Portugal
- 2021
-
In: International journal of earth sciences. - : Springer Nature. - 1437-3254 .- 1437-3262. ; 110:3, s. 911-922
-
Journal article (peer-reviewed)abstract
- The 150 Mt Lombador massive sulphide deposit is one of the seven known deposits of the Neves-Corvo mine. The deposit dips approximately 30o-35o to the NE and is open down dip, with current exploitation reaching down at 1 km depth. To investigate the possible downwards continuation of the deposit, a 1D constrained inversion of time-domain electromagnetic (TEM) ground loop data was conducted, followed by 3D electromagnetic (EM) forward modeling and a constrained 3D gravimetric inversion over the same area. To perform the EM and gravity modeling/inversion, a 3D geologic model was built using a density database comprising of approximately 300 drill-holes, and an electrical conductivity database with measurements from resistivity surveys and 1D inversion of the TEM data. The EM modeling shows that the Neves Formation shales are a regional conductive layer extending down to approximately 1.6 km depth in the Lombador area. This layer, often topped by massive sulphides, has an average density of 2.83 g/cm(3), whereas stockwork and massive sulphide reach on average 3.1 g/cm(3) and 4.5 g/cm(3), respectively. The 3D constrained gravity inversion results do not support the hypothesis of the presence of massive sulphides located in the down-dip direction of the Lombador deposit in the immediate vicinity of the known deposit. The lack of spatial resolution of the gravity grid, the study area limited size and the lack of information from within the basement suggest further studies are required to confirm the presence and amount of stockwork mineralization down-dip the Lombador deposit inside the Neves-Formation or the Phyllite-Quartzite basement.
|
|
| 5. |
- Freitag, Fabio Batista, et al.
(author)
-
Effect of luminosity on color discrimination of dichromatic marmosets (Callithrix jacchus)
- 2012
-
In: Optical Society of America. Journal A. - 1084-7529 .- 1520-8532. ; 29:2, s. A216-22
-
Journal article (peer-reviewed)abstract
- Psychophysical data have shown that under mesopic conditions cones and rods can interact, improving color vision. Since electrophysiological data have suggested that rods of dichromatic marmosets appear to be active at higher luminance, we aimed to investigate the effect of different levels of sunlight on the foraging abilities of male dichromatic marmosets. Captive marmosets were observed under three different conditions, with respect to their performance in detecting colored food items against a green background. Compared to high and low light intensities, intermediate luminosities significantly increased detection of orange targets by male dichromats, an indication of rod intrusion.
|
|
| 6. |
- Hansson, Henrik, et al.
(author)
-
Advanced Oxidation Treatment of Recalcitrant Wastewater from a Wood-Based Industry : a Comparative Study of O3 and O3/UV
- 2015
-
In: Water, Air and Soil Pollution. - : Springer Science and Business Media LLC. - 0049-6979 .- 1573-2932. ; 226:7
-
Journal article (peer-reviewed)abstract
- Ozone and ozone-based advanced oxidation processes were applied for the treatment of a recalcitrant wastewater generated by wood-based industries that contains different inorganic and organic constituents and high chemical oxygen demand (COD) varying between 3,400 and 4,000 mg/L. The investigation used a tubular ozone reactor combined with an UV reactor designed for different hydraulic retention times. The dependent variables addressed to evaluate the treatment efficiency were the reduction of COD and total organic carbon (TOC) and the biodegradability of the treated effluent based on respirometric studies using activated sludge from a wastewater treatment. The results showed that even though ozonation alone at acid pH promoted COD and TOC reductions of 65 and 31 % respectively, a decrease in the biodegradability was observed. The most effective treatment (COD and TOC reductions of 93 and 43 %, respectively) was obtained when applying ozone combined with UV light at basic pH. The ozone-UV combination was capable of increasing the amount of readily available COD by 75 % with an additional reduction of TOC by 60 %. In conclusion, ozonation at low pH effectively reduces the COD content in wastewater generated by the wood-based industry; however, in order to combine advanced oxidation with biological process, ozone combined with UV is recommended.
|
|
| 7. |
- Hansson, Henrik, 1978-, et al.
(author)
-
Photo-fenton and fenton oxidation of recalcitrant industrial wastewater
- 2012
-
In: Proceedings / Linnaeus ECO-TECH 2012, international conference on natural sciences and environmental technologies for waste and wastewater treatment, remediation, emissions related to climate, environmental and economic effects ; the eighth International Conference on the Establishment of Cooperation between Companies and Institutions in the Nordic Countries, the Baltic Sea Region, and the World, November 26-28, 2012, Kalmar, Sweden. - : Linnaeus University. - 9789186983864 ; , s. 187-
-
Conference paper (other academic/artistic)
|
|
| 8. |
- Hansson, Henrik, et al.
(author)
-
Photo-Fenton and Fenton Oxidation of Recalcitrant Industrial Wastewater Using Nanoscale Zero-Valent Iron
- 2012
-
In: International Journal of Photoenergy (Online). - : Hindawi Limited. - 1110-662X .- 1687-529X. ; 2012
-
Journal article (peer-reviewed)abstract
- There is a need for the development of on-site wastewater treatment technologies suitable for "dry-process industries," such as the wood-floor sector. Due to the nature of their activities, these industries generate lower volumes of highly polluted wastewaters after cleaning activities. Advanced oxidation processes such as Fenton and photo-Fenton, are potentially feasible options for treatment of these wastewaters. One of the disadvantages of the Fenton process is the formation of large amounts of ferrous iron sludge, a constraint that might be overcome with the use of nanoscale zero-valent iron (nZVI) powder. Wastewater from a wood-floor industry with initial COD of 4956 mg/L and TOC of 2730 mg/L was treated with dark-Fenton (nZVI/H2O2) and photo-Fenton (nZVI/H2O2/UV) applying a 2-level full-factorial experimental design. The highest removal of COD and TOC (80% and 60%, resp.) was achieved using photo-Fenton. The supply of the reactants in more than one dose during the reaction time had significant and positive effects on the treatment efficiency. According to the results, Fenton and mostly photo-Fenton are promising treatment options for these highly recalcitrant wastewaters. Future investigations should focus on optimizing treatment processes and assessing toxic effects that residual pollutants and the nZVI might have. The feasibility of combining advanced oxidation processes with biological treatment is also recommended.
|
|
| 9. |
- Hansson, Henrik, et al.
(author)
-
Photo-Fenton and Fenton Oxidation of Recalcitrant Wastewater from the Wooden Floor Industry
- 2015
-
In: Water environment research. - 1061-4303 .- 1554-7531. ; 87:6, s. 491-497
-
Journal article (peer-reviewed)abstract
- There is a need for development of on-site wastewater treatment technologies suitable to "dry-process'' industries, such as the wooden floor sector. Due to the nature of their activities, these industries generate low volumes of highly polluted and recalcitrant wastewaters due to washing and cleaning surfaces and machinery. Advanced oxidation processes such as Fenton and photo-Fenton are potentially feasible options for the treatment of wastewaters with not easily biodegradable pollutants. The wastewater from a wooden floor industry with initial COD value of 4956 mg/L and TOC value of 2730 mg/L was treated with Fenton (Fe/H2O2) and photo-Fenton (Fe/H2O2/UV) applying a 2-level full-factorial experimental design. The highest removals of COD and TOC (79% and 62% respectively) were achieved when photo-Fenton was applied. In conclusion, Fenton and photo-Fenton are promising treatment options for these highly recalcitrant wastewaters, photo-Fenton being a more promising option according to the results.
|
|
| 10. |
|
|
