| 1. |
- Dainiak, Maria B, et al.
(author)
-
Gelatin-fibrinogen cryogel dermal matrices for wound repair: Preparation, optimisation and in vitro study.
- 2010
-
In: Biomaterials. - : Elsevier BV. - 1878-5905 .- 0142-9612. ; 31, s. 67-76
-
Journal article (peer-reviewed)abstract
- Macroporous sponge-like gelatin-fibrinogen (Gl-Fg) scaffolds cross-linked with different concentrations (0.05-0.5%) of glutaraldehyde (GA) were produced using cryogelation technology, which allows for the preparation of highly porous scaffolds without compromising their mechanical properties, and is a more cost-efficient process than freeze-drying. The produced Gl-Fg-GA(X) scaffolds had a uniform interconnected open porous structure with a porosity of up to 90-92% and a pore size distribution of 10-120mum. All of the obtained cryogels were elastic and mechanically stable, except for the Gl-Fg-GA(0.05) scaffolds. Swelling kinetics and degradation rate, but not the porous structure of the cryogels, were strongly dependent on the degree of cross-linking. A ten-fold increase in the degree of cross-linking resulted in an almost 80-fold decrease in the rate of degradation in a solution of protease. Cryogels were seeded with primary dermal fibroblasts and the densities observed on the surface, plus the expression levels of collagen types I and III observed 5 days post-seeding, were similar to those observed on a control dermal substitute material, Integra((R)). Fibroblast proliferation and migration within the scaffolds were relative to the GA content. Glucose consumption rate was 3-fold higher on Gl-Fg-GA(0.1) than on Gl-Fg-GA(0.5) cryogels 10 days post-seeding. An enhanced cell motility on cryogels with reducing GA crosslinking was obtained after long time culture. Particularly marked cell infiltration was seen in gels using 0.1% GA as a crosslinker. The scaffold started to disintegrate after 42 days of in vitro culturing. The described in vitro studies demonstrated good potential of Gl-Fg-GA(0.1) scaffolds as matrices for wound healing.
|
|
| 2. |
- Ivanov, Alexander, et al.
(author)
-
Boronate-containing polymer brushes: Characterization, interaction with saccharides and mammalian cancer cells.
- 2009
-
In: Journal of Biomedical Materials Research. Part A. - : Wiley. - 1552-4965 .- 1549-3296. ; 88:1, s. 213-225
-
Journal article (peer-reviewed)abstract
- Boronate-containing polymer brushes were synthesized by free radical copolymerization of N,N-dimethylacrylamide (DMAA) and N-acryloyl-m-phenylboronic acid (NAAPBA) (9:1) on the surface of 3-mercaptopropyl-silylated glass plates and capillaries. The brushes were characterized with time-of-flight secondary ion mass-spectrometry (ToF SIMS), atomic force microscopy and contact angle measurements. Fructose caused a well-expressed drop spreading on the surface of copolymer-grafted glass, due to the strong interaction with the boronate groups. Sedimentation of murine hybridoma cells M2139 or human myeloid leukemia cells KG1 onto the DMAA-NAAPBA copolymer-grafted glass plates from 10 mM phosphate buffer solution (pH 8.0) resulted in the cell adhesion. The adhered M2139 and KG1 cells could be quantitatively detached from the grafted plates with 0.1M fructose, which competed with cell surface carbohydrates for binding to the boronates. Evaluation of the binding strength between M2139 cells and the copolymer brush was performed by exposure of the adhered cells to a shear stress. Detachment of a fraction of 18% of the adhered M2139 cells was obtained at a shear force of 1400-2800 pN/cell generated by the running phosphate buffer (pH 8.0), whereas the remaining adhered cells (70%) could be detached with 0.1M fructose dissolved in the same buffer. Possible applications of the boronate-containing polymer brushes to affinity cell separation can be based upon the facile recovery of the attached cells. (c) 2008 Wiley Periodicals, Inc. J Biomed Mater Res 2008.
|
|
| 3. |
- Ivanov, Alexander, et al.
(author)
-
Thin semitransparent gels containing phenylboronic acid: porosity, optical response and permeability for sugars.
- 2008
-
In: Journal of Molecular Recognition. - : Wiley. - 1099-1352 .- 0952-3499. ; 21:2, s. 89-95
-
Journal article (peer-reviewed)abstract
- Radical copolymerization of acrylamide (Am) (90 mol%) with N-acryloyl-m-aminophenylboronic acid (NAAPBA) (10 mol%) carried out on the surface of glass slides in aqueous solution and in the absence of chemical cross-linkers, resulted in the formation of thin semitransparent gels. The phenylboronic acid (PBA) ligand density was ca. 160 micromol/ml gel. The gels exhibited a macroporous structure and displayed optical response to sucrose, lactose, glucose and fructose in 50 mM sodium phosphate buffer, in the pH range from 6.5 to 7.5. The response was fairly reversible and linearly depended on glucose concentration in the wide concentration range from 1 to 60 mM at pH 7.3. The character of response was explained by the balance of two competing equilibrium processes: binding of glucose to phenylboronate anions and binary hydrophobic interactions of neutral PBA groups. The apparent diffusion coefficient of glucose in the gels was ca. 2.5 x 10(-7) cm(2)/s. A freshly prepared gel can be used daily for at least 1 month without changes in sensitivity. Autoclaving (121 degrees C, 1.2 bar, 10 min) allows for the gels sterilization, which is important for their use as glucose sensors in fermentation processes. Copyright (c) 2008 John Wiley & Sons, Ltd.
|
|
| 4. |
- Savina, Irina N., et al.
(author)
-
Biomimetic Macroporous Hydrogels: Protein Ligand Distribution and Cell Response to the Ligand Architecture in the Scaffold
- 2009
-
In: Journal of Biomaterials Science. Polymer Edition. - 0920-5063. ; 20:12, s. 1781-1795
-
Journal article (peer-reviewed)abstract
- Macroporous hydrogels (MHs), cryogels, are a new type of biomaterials for tissue engineering that can be produced from any natural or synthetic polymer that forms a gel. Synthetic MHs are rendered bioactive by surface or bulk modifications with extracellular matrix components. In this study, cell response to the architecture of protein ligands, bovine type-I collagen (CG) and human fibrinogen (Fg), immobilised using different methods on poly(2-hydroxyethyl methacrylate) (pHEMA) macroporous hydrogels (MHs) was analysed. Bulk modification was performed by cross-linking cryo-co-polymerisation of HEMA and poly(ethylene glycol) diacrylate (PEGA) in the presence of proteins (CG/ pHEMA and Fg/pHEMA MHs). The polymer surface was modified by covalent immobilisation of the proteins to the active epoxy (ep) groups present on pHEMA after hydrogel fabrication (CG-epHEMA and Fg-epHEMA MHs). The concentration of proteins in protein/pHEMA and protein-epHEMA MHs was 80-85 and 130-140 mu g/ml hydrogel, respectively. It was demonstrated by immunostaining and confocal laser scanning microscopy that bulk modification resulted in spreading of CG in the polymer matrix and spot-like distribution of Fg. On the contrary, surface modification resulted in spot-like distribution of CG and uniform spreading of Fg, which evenly coated the surface. Proliferation rate of fibroblasts was higher on MHs with even distribution of the ligands, i.e., on Fg-epHEMA and CG/ pHEMA. After 30 days of growth, fibroblasts formed several monolayers and deposited extracellular matrix filling the pores of these MHs. The best result in terms of cell proliferation was obtained on Fg-epHEMA. The ligands displayed on surface of these scaffolds were in native conformation, while in bulk-modified CG/ pHEMA MHs most of the proteins were buried inside the polymer matrix and were less accessible for interactions with specific antibodies and cells. The method used for MH modification with bioligands strongly affects spatial distribution, density and conformation of the ligand on the scaffold surface, which, in turn, influence cell-surface interactions. The optimal type of modification varies depending on intrinsic properties of proteins and MHs. (C) Koninklijke Brill NV, Leiden, 2009
|
|
