1. |
- Romanelli, F, et al.
(author)
-
Overview of the JET results
- 2011
-
In: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 51:9
-
Journal article (peer-reviewed)abstract
- Since the last IAEA Conference JET has been in operation for one year with a programmatic focus on the qualification of ITER operating scenarios, the consolidation of ITER design choices and preparation for plasma operation with the ITER-like wall presently being installed in JET. Good progress has been achieved, including stationary ELMy H-mode operation at 4.5 MA. The high confinement hybrid scenario has been extended to high triangularity, lower ρ*and to pulse lengths comparable to the resistive time. The steady-state scenario has also been extended to lower ρ*and ν*and optimized to simultaneously achieve, under stationary conditions, ITER-like values of all other relevant normalized parameters. A dedicated helium campaign has allowed key aspects of plasma control and H-mode operation for the ITER non-activated phase to be evaluated. Effective sawtooth control by fast ions has been demonstrated with3He minority ICRH, a scenario with negligible minority current drive. Edge localized mode (ELM) control studies using external n = 1 and n = 2 perturbation fields have found a resonance effect in ELM frequency for specific q95values. Complete ELM suppression has, however, not been observed, even with an edge Chirikov parameter larger than 1. Pellet ELM pacing has been demonstrated and the minimum pellet size needed to trigger an ELM has been estimated. For both natural and mitigated ELMs a broadening of the divertor ELM-wetted area with increasing ELM size has been found. In disruption studies with massive gas injection up to 50% of the thermal energy could be radiated before, and 20% during, the thermal quench. Halo currents could be reduced by 60% and, using argon/deuterium and neon/deuterium gas mixtures, runaway electron generation could be avoided. Most objectives of the ITER-like ICRH antenna have been demonstrated; matching with closely packed straps, ELM resilience, scattering matrix arc detection and operation at high power density (6.2 MW m-2) and antenna strap voltages (42 kV). Coupling measurements are in very good agreement with TOPICA modelling. © 2011 IAEA, Vienna.
|
|
2. |
- Abel, I, et al.
(author)
-
Overview of the JET results with the ITER-like wall
- 2013
-
In: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10, s. 104002-
-
Journal article (peer-reviewed)abstract
- Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Z(eff) (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. The re-establishment of the baseline H-mode and hybrid scenarios compatible with the new wall has required an optimization of the control of metallic impurity sources and heat loads. Stable type-I ELMy H-mode regimes with H-98,H-y2 close to 1 and beta(N) similar to 1.6 have been achieved using gas injection. ELM frequency is a key factor for the control of the metallic impurity accumulation. Pedestal temperatures tend to be lower with the new wall, leading to reduced confinement, but nitrogen seeding restores high pedestal temperatures and confinement. Compared with the carbon wall, major disruptions with the new wall show a lower radiated power and a slower current quench. The higher heat loads on Be wall plasma-facing components due to lower radiation made the routine use of massive gas injection for disruption mitigation essential.
|
|
3. |
- Ingesson, L. C., et al.
(author)
-
Progress on common aspects of the EU-supplied ITER diagnostics and prediction of diagnostic performance
- 2006
-
In: Review of Scientific Instruments. - : AIP Publishing. - 0034-6748 .- 1089-7623. ; 77:10, s. 10F502-
-
Journal article (peer-reviewed)abstract
- The European Union will supply a number of diagnostics for ITER. Significant progress has been made on the design and integration of these diagnostics. Specific topics, in common for several of the diagnostics, discussed are port-plug integration, simplification of labyrinths against neutron streaming, and design measures to protect and to be able to replace sensitive optical components. Performance analysis to predict the likely capability of the diagnostics to meet the ITER measurement requirements will be an important aspect of the design process. The interpretation of the measurement requirements, specifically of spatial resolution in the case of indirect measurements, is discussed on the basis of two examples, and methods of performance analysis are compared.
|
|
4. |
- Moro, F., et al.
(author)
-
Neutronic calculations in support of the design of the ITER High Resolution Neutron Spectrometer
- 2011
-
In: Fusion engineering and design. - : Elsevier BV. - 0920-3796 .- 1873-7196. ; 86:6-8, s. 1277-1281
-
Journal article (peer-reviewed)abstract
- This paper presents the results of neutronic calculations performed to address important issues related to the optimization of the ITER HRNS (High resolution Neutron Spectrometer) design, in particular concerning the definition of the collimator and the choice of the detector system. The calculations have been carried out using the MCNP5 Monte Carlo code in a full 3-D geometry. The HRNS collimation system has been included in the latest MCNP ITER 40 model (Alite-4). The ITER scenario 2 reference DT plasma fusion neutron source peaked at 14.1 MeV with Gaussian energy distribution has been used. Neutron fluxes and energy spectra (>1 MeV) have been evaluated at different positions along the HRNS collimator and at the detector location. The noise-to-signal ratio (i.e. the ratio of collided to uncoilided neutrons), the breakdown of the collided spectrum into its components, the dependency on the first wall aperture and the gamma-ray spectra at the detector position have also been analyzed. The impact of the results on the design of the HRNS diagnostic system is discussed.
|
|
5. |
- Villari, R., et al.
(author)
-
Shutdown dose rate benchmark experiment at JET to validate the three-dimensional Advanced-D1S method
- 2012
-
In: Fusion engineering and design. - : Elsevier BV. - 0920-3796 .- 1873-7196. ; 87:7-8, s. 1095-1100
-
Journal article (peer-reviewed)abstract
- The paper describes a new benchmark, performed as a preliminary experiment on JET tokamak during the last shutdown. Dose rate has been measured with different dosimeters along the axis of the main horizontal port of Octant 1, from the plasma centre to 1 m outside the port at various times after shutdown. The activation dose from the horizontal neutron camera, moved outside the torus hall during the shutdown, has also been assessed. The measured values have been compared with dose rates calculated using an Advanced-D1S method in which new computation capabilities have been introduced, such as dose rate spatial mesh map and automated time behaviour. Measurements along the axis of the horizontal port are well predicted by the calculation. With few exceptions, the D1S estimation is within the error of the measurements. The activation of the horizontal camera is underestimated by a factor of 2. However, more accurate measurements are needed to reduce the uncertainties. The Advanced-D1S method, the results and implications of the benchmark are presented and discussed.
|
|