| 1. |
- Duan, Yumin, et al.
(author)
-
Succession of keratin-degrading bacteria and associated health risks during pig manure composting
- 2020
-
In: Journal of Cleaner Production. - : Elsevier. - 0959-6526 .- 1879-1786. ; 258
-
Journal article (peer-reviewed)abstract
- The alteration of microbial dynamics and their divergence were evaluated in bristles containing pig manure (PM) compost with different concentrations of coconut shell biochar [0% (T1), 2.5% (T2), 5.0% (T3), 7.5% (T4) and 10% (T5)] amendment. The results revealed that the CB amendment significantly increased the keratin degradation efficiency and bacterial diversity during composting. The richest bacterial diversity and the highest keratin reduction of 39.1% were observed in the PM compost with a 7.5% CB amendment. The most abundant phyla were Firmicutes and Actinobacteria (which accounted for 87.91% and 12.09%, respectively), and the superior genera were Bacilli and Clostridia (which accounted for 23.52% and 61.17%, respectively). In addition, a dimensionality analysis from principal coordinate’s analysis and non-metric multidimensional scaling showed that the bacterial community had a significant divergence among the different dosages of CB. Furthermore, the correlation found in a canonical correspondence analysis illustrated that the physio-chemical environmental factors were more relevant for the bacterial community within the CB in the compost than in that in the control sample. Overall, the application of biochar for composting altered the typical selectivity for functional bacteria and further influenced the organic waste biotransformation during bristle-containing PM composting. (C) 2020 Elsevier Ltd. All rights reserved.
|
|
| 2. |
- Mukesh Kumar, Awasthi, et al.
(author)
-
Biotechnological strategies for bio-transforming biosolid into resources toward circular bio-economy : A review
- 2022
-
In: Renewable & sustainable energy reviews. - : Elsevier. - 1364-0321 .- 1879-0690. ; 156
-
Research review (peer-reviewed)abstract
- Biosolids are the biological organic matter extracted from various treatment processes of wastewater which are considered as a rich source of energy and nutrients. The most commonly used method for the disposal of biosolids is landfilling. But this causes the loss of valuable nutrients and creates environmental issues. Circular economy approaches provide a better way for utilization these resources in a sustainable manner. This allows maximum utilization of resources and many natural resources can be preserved and utilized for future generations. The present review provides a comprehensive illustration of biotechnological approaches for the utilization of biosolids. Various process strategies for the utilization of biosolids for the production of energy, fuels and valueadded products are discussed. The utilization of this rich organic matter under circular economy has also been described in detail.
|
|
| 3. |
- Fulmali, Abhinav Omprakash, et al.
(author)
-
Water diffusion kinetics study at different hydrothermal bath temperatures and subsequent durability studies of CNT embedded fibrous polymeric composites: Roles of CNT content, functionalization and in‐situ testing temperature
- 2023
-
In: Journal of Applied Polymer Science. - : Wiley. - 0021-8995 .- 1097-4628. ; 140:11
-
Journal article (peer-reviewed)abstract
- Although structural polymers like epoxy are extensively used in marine applications over metallic structures, environmental water tends to ingress into this polymer which may affect its long-term durability. The extent of degradation caused by the absorbed water on polymeric composite's mechanical properties depends on the water diffusion mechanism, environmental temperature and subsequent reversible and irreversible chemical restructuring of the polymer. In this study, hydrothermal conditioning behavior of glass fiber reinforced epoxy (GE) composites with varying (0.1, 0.3, and 0.5) wt.% of pristine and functionalized carbon nanotubes (CNTs and FCNTs) was studied at 15°C (Low-Temperature Hydrothermal Conditioning (LTHC)) and 50°C (Elevated-Temperature Hydrothermal Conditioning (ETHC)) water baths. The changes in chemical bonding characteristics and glass transition temperature of GE composite due to above mentioned factors have been studied by Fourier transformed infrared spectroscopy and differential scanning calorimetry. The gravimetric analysis was employed to monitor the water uptake kinetics of the composites and flexural strength of conditioned composites after 50 days of conditioning and saturation was study to understand the effect of water sorption. Experimental results revealed that, FCNTs greatly hinders the water absorption through the interfaces at LTHC, as the equilibrium water content of 0.1FCNT-GE composite was ~9.5% and ~3.0% and Diffusion coefficient was ~60.0% and ~15.5% lower than the GE and 0.1CNT-GE composites, respectively at LTHC. At LTHC, the water saturated 0.1FCNT-GE composites exhibited superior flexural strength than GE and 0.1CNT-GE composites. At ETHC, generation of hygroscopic stresses and unfavorable stresses at the weak CNT/polymer interface adversely affected the 0.1CNT-GE composites water resistance compared to 0.1FCNT-GE composites with stronger FCNT/polymer interface. The extent of recovery in the flexural strength was evaluated by complete desorption of water-saturated specimens. Finally, a fractography study was conducted to understand the variation in the well-being of the glass fiber/polymer and nanotube/polymer interface due to mentioned varying factors.
|
|
| 4. |
- Kumar Ramamoorthy, Sunil, 1987-, et al.
(author)
-
Functionalization of Carbon Nanotube
- 2021
-
In: Handbook of Carbon Nanotubes. - Cham : Springer. - 9783319706146
-
Book chapter (peer-reviewed)abstract
- One-dimensional carbon nanotubes (CNTs) have outstanding mechanical properties, making them a good candidate for reinforcement application in polymer and fiber-reinforced polymer composites. Superior properties of the CNTs are exploited regularly by reinforcing these nanotubes in a polymer matrix. However, strong Van der Waals interaction energy of tube-tube contact, high electrostatic interaction between the tubes, small tube size, and large surface area of the tubes render CNT dispersion a problematic task. Therefore, to improve its dispersion and alignment in the composite, researchers have developed innovative techniques to strengthen the properties of the composite. For achieving optimum and reproducible mechanical properties in a composite, fine dispersion of CNTs, their alignment, and strong interfacial adhesion with polymer is a demand to be guaranteed. In this chapter, the principles and techniques for uniform dispersion and alignment of CNTs in the polymer and fiber-reinforced polymer composite are discussed.
|
|
| 5. |
- Ramamoorthy, Sunil Kumar, et al.
(author)
-
Biocomposites From Regenerated Cellulose Textile Fibers And Bio-Based Thermoset Matrix For Automotive Applications
- 2013
-
Conference paper (peer-reviewed)abstract
- Biocomposites were produced from regenerated cellulose fiber reinforcement and soybean based bio-matrix. Mechanical, thermal, viscoelastic and morphological results show the good potential of these composites to be used as structural materials in automotive industries. This article focuses on manufacturing and testing of these composites for engineering materials. Regenerated cellulose fibers such as Lyocell and viscose were reinforced in soybean based thermoset matrix to produce composites by compression molding. Hybrid composites were produced by mixing both these fibers at known ratio and the total fiber content in composite was between 40 and 60 weight %. In general, Lyocell based composites showed better tensile properties than viscose based composites. Composites consisting 60 weight % Lyocell and rest with matrix had tensile strength of 135 MPa and tensile modulus of 17 GPa. These composites also showed good flexural properties; flexural strength of 127 Mpa and flexural modulus of 7 GPa. Dynamic mechanical thermal analysis showed that these composites had good viscoelastic properties. Viscose based composites had better percentage elongation during tensile test. These composites also showed relatively good impact and viscoelastic properties. Scanning electron microscope images showed that the composites had good fiber-matrix adhesion. Several efforts are made to produce sustainable biomaterials to replace synthetic materials due to inherent properties like renewable, biodegradable and low density. Biocomposites play significant role in sustainable materials which has already found applications in automotive and construction industries. Many researchers produced biocomposites from natural fiber and bio-based/synthetic matrix and it had found several applications. There are several disadvantages of using natural fiber in composites; quality variation, place dependent, plant maturity, harvesting method, high water absorption etc. These composites also give odor which has to be avoided in indoor automotive applications. These natural fibers can be replaced with lignocelluloses, agro mass and biomass to develop biocomposites as they are from natural origin. Lyocell and viscose are manmade regenerated cellulose fibers which is from natural origin has excellent properties. These fibers can be used as reinforcements to produce biocomposites which can overcome most of the above listed disadvantages of natural fibers. Many composites were made from natural fiber reinforcement and petroleum based synthetic matrix. Researchers have been finding ways to get matrix out of natural resources like soybean and linseed on chemical modifications. This article is focused on producing and testing sustainable material with regenerated cellulose and soybean based bio-matrix for automotive applications.
|
|
| 6. |
- Ramamoorthy, Sunil Kumar, et al.
(author)
-
Characterization Of Wood Based Fiber Reinforced Bio-Composites
- 2013
-
Conference paper (peer-reviewed)abstract
- Natural fiber composites have got more focus in recent times due to their intrinsic properties such as lightweight, biodegradable, low cost etc. Several researchers have made bio-composites out of many natural fibers such as jute, flax, sisal. These composites have large market in Europe and North America where it is used in automobile and construction industry. A lot of research has been done to improve the properties such as surface modification of fiber, manufacturing hybrid composites. However, the natural fibers are dissimilar and vary largely due to many factors such as variety, harvest, maturity, climate etc. Apart from technical drawbacks, these fibers grow only in certain countries such as India and China. High demand raised the price of these fibers which increases the product price as well. Wood-based fibers such as Lyocell and Viscose was used to make composites in order to make less variation in products, decrease the dependency of natural fibers, promoting locally available fibers and encourage forest products as value-added products. Lyocell and viscose fibers have relatively less variation and high quality. Bio-composites were made by reinforcing wood-based fibers in soybean based thermoset matrix. Hybrid composites were prepared by mixing two different wood-based fibers in known ratio. The fiber content in the composites was between 40 and 60 weight%. Mechanical properties were characterized by tensile, flexural and impact tests. Lyocell and viscose based composites had better mechanical properties than jute fiber composites. Alkali treatment of Lyocell fibers improved the mechanical properties of the composites. The behaviour of wood-based fiber composites were studied under wet environment as well. In wet environment, the mechanical properties of wood-based fiber composites were superior to jute fiber composites. Lyocell based composites had tensile strength of 135 MPa and tensile modulus of 17 GPa. The composites had flexural strength of 127 MPa and flexural modulus of 7 GPa. Better percentage elongation was obtained when viscose fiber was reinforced in matrix. Viscose composites had better impact strength and viscoelastic properties. The change in properties in two different wood-based fibers (Lyocell and viscose) lies in the morphology of the fiber itself. Hybrid composites were produced and the effect of hybridization was clear in most of the cases. The properties were able to be tailored by making hybrid composites, by changing the amount of each fiber in the composites. The results (tensile and flexural) were competitive and fulfil the requirements of these composites to be used in several applications including automotive headliners, car door panel, construction door frame etc. The forest products such as wood fibers could be used in composites to produce environmentally friendly products and promote forest industry. Wood-based fibers such as Lyocell and Viscose was used to make composites in order to make less variation in products, decrease the dependency of natural fibers, promoting locally available fibers and encourage forest products. Bio-composites were made by reinforcing wood-based fibers in soybean based thermoset matrix. Hybrid composites were prepared by mixing two different wood-based fibers in known ratio. Mechanical properties were characterized by tensile, flexural and impact tests. Lyocell and viscose based composites had better mechanical properties than jute fiber composites. Alkali treatment of Lyocell fibers improved the mechanical properties of the composites. The behaviour of wood-based fiber composites were studied under wet environment as well. In wet environment, the mechanical properties of wood-based fiber composites were superior to jute fiber composites. Lyocell based composites had tensile strength of 135 MPa and tensile modulus of 17 GPa. The composites had flexural strength of 127 MPa and flexural modulus of 7 GPa. Viscose composites had better impact strength and viscoelastic properties. The result fulfils the requirements of these composites to be used in several applications including automotive headliners, car door panel etc. The forest products could be used in composites to produce environmentally friendly products and promote forest industry.
|
|
| 7. |
- Ramamoorthy, Sunil Kumar, et al.
(author)
-
Green Composites Based On Regenerated Cellulose Textile Fibers For Structural Composites
- 2013
-
Conference paper (peer-reviewed)abstract
- Composites were manufactured from regenerated cellulose and biobased matrix by compression molding. The reinforcing materials used were Lyocell and viscose, while the matrix used was chemically modified soybean oil. Hybrid composites were prepared by mixing both the fibers. The total fiber content in the composites was between 40-60 weight %. Lyocell based composites had better tensile properties than viscose based composites; composites consisting 60 weight % Lyocell impregnated with matrix had tensile strength of 135 MPa and tensile modulus of 17 GPa. These composites also showed better flexural properties; flexural strength of 127 MPa and flexural modulus of 7 GPa. Dynamic mechanical thermal analysis results showed that these composites had good viscoelastic properties. Viscose based composites had better percentage elongation; these composites also showed relatively good impact and viscoelastic properties. Hybrid composites showed good mechanical and viscoelastic properties. Scanning electron microscope images showed that the composites had good fiber-matrix adhesion.
|
|
| 8. |
- Ramamoorthy, Sunil Kumar, et al.
(author)
-
Properties of green composites with regenerated cellulose fiber and soybean-based thermoset for technical applications
- 2014
-
In: Journal of reinforced plastics and composites (Print). - : SAGE. - 0731-6844 .- 1530-7964. ; 33:2, s. 193-201
-
Journal article (peer-reviewed)abstract
- Composites were developed by reinforcing available non-woven Lyocell and viscose in acrylated epoxidized soybean oil (AESO). Compression molding was used to make composites with 40–60 wt% fiber content. The fiber content comprises only Lyocell or viscose fiber, or mixture of these fibers in known ratio. Hybrid composites were made by a mixture of both the fibers in known ratio and it affects the properties. The effect of hybridization was evident in most tests which gives us an opportunity to tailor the properties according to requirement. Lyocell fiber reinforced composites with 60 wt% fiber content had a tensile strength and modulus of about 135 MPa and 17 GPa, respectively. Dynamic mechanical analysis showed that the Lyocell fiber reinforced composites had good viscoelastic properties. The viscose fiber reinforced composites had the high percentage elongation and also showed relatively good impact strength and flexural modulus. Good fiber-matrix adhesion reflected in mechanical properties. SEM images were made to see the fiber-matrix compatibility.
|
|
| 9. |
- Ramamoorthy, Sunil Kumar, et al.
(author)
-
Regenerated Cellulose Fiber Reinforced Composites
- 2013
-
Conference paper (peer-reviewed)abstract
- Wood pulp based regenerated cellulose fibers like Lyocell and viscose which are from natural origin have high and even quality; used to develop superior composites with good properties. In this project, Lyocell and viscose fibers were reinforced in chemically modified soybean based bio-matrix, acrylated epoxidized soybean oil (AESO) by compression molding technique. The composites are characterized for mechanical performance by tensile, flexural and impact tests, viscoelastic performance by dynamical mechanical thermal analysis (DMTA) and morphological analysis by scanning electron microscopy (SEM). In general, Lyocell composites had better tensile and flexural properties than viscose based composites. The same goes with elastic and viscous response of the composites. Hybrid composites were formed by fiber blending; on addition of Lyocell to viscose based composites improved the properties. The amount of Lyocell and viscose fibers used determined the properties of hybrid composites and the possibility of tailoring properties for specific application was seen. Hybrid composites showed better impact strength. Morphological analysis showed that the viscose composites had small fiber pull out whereas Lyocell composites had few pores. Hybrid composite analysis showed that they had uneven spreading of matrix; delamination occurred on constant heating and cooling. To overcome the above mentioned issue and to reduce the water absorption, surface modification of the fiber was done by alkali treatment and silane treatment. The effect of treatment is done through swelling, water absorption and morphological analysis tests. The properties could be increased on proper modification of the fibers. The results show the good potential of these composites to be used in automotives and construction industries.
|
|
| 10. |
- Akbari, Samira, et al.
(author)
-
Novel Bio-based Branched Unsaturated Polyester Resins for High-Temperature Applications
- 2023
-
In: Journal of Polymers and the Environment. - 1566-2543 .- 1572-8919.
-
Journal article (peer-reviewed)abstract
- Unsaturated polyester resins, one of the most important thermosets, are invariably produced from oil-based monomers. Their application is limited in areas where high thermal stability is required due to their low Tg. Besides, these resins contain 30–40% hazardous styrene as a reactive solvent. Therefore, developing bio-based solventless unsaturated polyester resin with medium to high thermomechanical properties compared to petrochemical-based counterparts is important. In order to achieve this, a series of branched bio-based unsaturated polyester resins were synthesized using bulk polymerization method in two steps. In the first step, four different intermediates were prepared by reacting glycerol (as a core molecule) with either isosorbide (diol), 1,3-propanediol (diol), 2,5-furandicarboxylic acid (saturated diacid), or adipic acid (saturated diacid). In the second step, the branched intermediate was end capped with methacrylic anhydride to introduce reactive sites for cross-linking on the branch ends. The chemical structure of the resins was characterized by 13C-NMR. FT-IR confirmed the polycondensation reaction in the first step and the end functionalization of the resins with methacrylic anhydride in the second step. The effect of 2,5-furandicarboxylic acid and isosorbide on thermomechanical and thermal properties was investigated using dynamic mechanical analysis, differential scanning calorimetry, and thermo-gravimetric analysis. Results indicated that 2,5-furandicarboxylic acid based resins had superior thermomechanical properties compared to a commercial reference unsaturated polyester resin, making them promising resins for high-temperature composite applications. For example, the resin based on 2,5-furandicarboxylic acid and isosorbide and the resin based on 2,5-furandicarboxylic acid and 1,3-propanediol gave glass transition temperatures of 173 °C and 148 °C, respectively. Although the synthesized 2,5-furandicarboxylic acid based resins had higher viscosity (22.7 Pas) than conventional unsaturated polyester (0.4–0.5 Pas) at room temperature, preheated resins can be used for making high-temperature-tolerance fiber-reinforced composite.
|
|
