1. |
- Aryal, Pradip, et al.
(author)
-
Comparative study of the main electromagnetic models applied to melt pool prediction with gas metal arc : Effect on flow, ripples from drop impact, and geometry
- 2022
-
In: International Journal of Heat and Mass Transfer. - : Elsevier. - 0017-9310 .- 1879-2189. ; 194
-
Journal article (peer-reviewed)abstract
- The present work concerns the electromagnetic force models in computational fluid dynamics simulations of melt pools produced with electric arcs. These are commonly applied to gas metal arcs with metal transfer, in welding and additive manufacturing. Metal drop impact on the melt pool is thus included in this study. The electromagnetic force models applied in literature use either numerical solutions of Poisson equations or one of the two analytical models developed by Kou and Sun, or Tsao and Wu. These models rely on assumptions for which the effect on the melt pool predictions remains to be understood. The present work thoroughly investigates those assumptions and their effects. It has been supported by dedicated experimental tests that did provide estimates of unknown model parameters and validation data. The obtained results show that the assumptions that fundamentally distinguish these three models change the electromagnetic force, including the relation between its components. These changes, which can also be spatially non-uniform, are large. As a result, these models lead to significantly different recirculation flow pattern, thermal convection, melt pool morphology, bead dimensions, and free surface response to the metal transfer. We conclude by proposing conditions in which each of these models is suited or questionable.
|
|
2. |
- Aryal, Pradip, et al.
(author)
-
Effect of Substrate Orientation on Melt Pool during Multi-Layer Deposition in V-Groove with Gas Metal Arc
- 2021
-
In: Proceedings of the World Congress on Mechanical, Chemical, and Material Engineering. - : Avestia Publishing. - 2369-8136. - 9781927877616
-
Conference paper (peer-reviewed)abstract
- Thermo-fluid dynamic and experimental approaches are used to investigate the influence of 20° uphill, downhill and sideway substrate orientation during metal deposition over a previously deposited bead in a V-groove. The computational fluid dynamic model with free surface deformation and metal transfer gives insight into the melt pool flow and causes of defect formation observed on the solidified beads. The experimental metallographs, high-speed images and computational results show good agreement. It is found that the deposition of a second layer on a smooth first layer cooled down to room temperature leads to large changes in melt pool flow pattern at 20° substrate inclination compared to flat condition. It results in undercut and humps with the uphill orientation and undercut with the side inclination. Therefore, lower angle range is necessary for multilayer gas metal arc deposition for these two last configurations.
|
|
3. |
- Ancona, Antonio, 1974-, et al.
(author)
-
Monitoring and control of directed energy deposition using a laser beam
- 2023. - 1.
-
In: Additive Manufacturing of High-Performance metallic Materials. - : Elsevier. - 9780323918855 - 9780323913829 ; , s. 612-638
-
Book chapter (peer-reviewed)abstract
- To be a successful competitor among other technologies, metallic laser-directed energy depositionusing a laser beam would benefit from the support of intelligent automation making the processrobust, repeatable, and cost-efficient. This calls for technology leaps towards robust and accuratedetection and estimation of the conditions during processing and control schemes for robustperformance. This chapter discusses how developments in sensor technology and model-basedsignal processing can contribute to advancements in in-process monitoring of directed energydeposition using a laser beam and how developments in model-based feedforward- and feedbackcontrol can support automation. The focus is on how machine vision, optical emission spectroscopy,thermal sensing, and electrical process signals can support monitoring, control and better processunderstanding. These approaches are industrially relevant and have a high potential to support amore sustainable manufacturing.
|
|
4. |
- Elefante, Arianna, et al.
(author)
-
Detecting beam offsets in laser welding of closed-square-butt joints by wavelet analysis of an optical process signal
- 2019
-
In: Optics and Laser Technology. - : Elsevier BV. - 0030-3992 .- 1879-2545. ; 109, s. 178-185
-
Journal article (peer-reviewed)abstract
- Robotized laser beam welding of closed-square-butt joints is sensitive to the positioning of the laser beam with respect to the joint since even a small offset may result in a detrimental lack of sidewall fusion. An evaluation of a system using a photodiode aligned coaxial to the processing laser beam confirms the ability to detect variations of the process conditions, such as when there is an evolution of an offset between the laser beam and the joint. Welding with different robot trajectories and with the processing laser operating in both continuous and pulsed mode provided data for this evaluation. The detection method uses wavelet analysis of the photodetector signal that carries information of the process condition revealed by the plasma plume optical emissions during welding. This experimental data have been evaluated offline. The results show the potential of this detection method that is clearly beneficial for the development of a system for welding joint tracking.
|
|
5. |
- Fang, Jingzhong, et al.
(author)
-
A New Particle Swarm Optimization Algorithm for Outlier Detection : Industrial Data Clustering inWire Arc Additive Manufacturing
- 2023
-
In: IEEE Transactions on Automation Science and Engineering. - 1545-5955 .- 1558-3783. ; 21:2, s. 1244-1257
-
Journal article (peer-reviewed)abstract
- In this paper, a novel outlier detection method is proposed for industrial data analysis based on the fuzzy C-means (FCM) algorithm. An adaptive switching randomly perturbed particle swarm optimization algorithm (ASRPPSO) is put forward to optimize the initial cluster centroids of the FCM algorithm. The superiority of the proposed ASRPPSO is demonstrated over five existing PSO algorithms on a series of benchmark functions. To illustrate its application potential, the proposed ASRPPSO-based FCM algorithm is exploited in the outlier detection problem for analyzing the real-world industrial data collected from a wire arc additive manufacturing pilot line in Sweden. Experimental results demonstrate that the proposed ASRPPSO-based FCM algorithm out performs the standard FCM algorithm in detecting outliers of real-world industrial data.Note to PractitionersElectric arc (which is governed by the current and arc voltage) plays a significant role in monitoring the operating status of the wire arc additive manufacturing (WAAM) process. The nominal periodic current and voltage may occasionally change abruptly due to anomalies (such asarc instability, unstable metal transfer, geometrical deviations, and surface contaminations), which would affect the quality of the fabricated component. This paper focuses on detecting possible anomalies by analyzing the current and voltage during the WAAM process. A novel clustering-based outlier detection method is proposed for anomaly detection where abnormal and normal instances are categorized into two separate clusters. A new particle swarm optimization algorithm is put forward to optimize the initial cluster centroid so as to improve the detection accuracy. The proposed outlier detection method is applied to real-world data collected from a WAAM pilot line for detecting abnormal instances. Experimental results demonstrate the effectiveness of the proposed outlier detection method. The proposed outlier detection method can be applied to other industrial applications including electrical engineering, mechanical engineering and medical engineering. In the future, we aim to develop an online outlier detection system based on the proposed method for real-time for anomaly detection and defect prediction.
|
|
6. |
- Hagqvist, Petter, 1986, et al.
(author)
-
Emissivity compensated spectral pyrometry-algorithm and sensitivity analysis
- 2014
-
In: Measurement Science and Technology. - : IOP Publishing. - 0957-0233 .- 1361-6501. ; 25:2
-
Journal article (peer-reviewed)abstract
- In order to solve the problem of non-contact temperature measurements on an object with varying emissivity, a new method is herein described and evaluated. The method uses spectral radiance measurements and converts them to temperature readings. It proves to be resilient towards changes in spectral emissivity and tolerates noisy spectral measurements. It is based on an assumption of smooth changes in emissivity and uses historical values of spectral emissivity and temperature for estimating current spectral emissivity. The algorithm, its constituent steps and accompanying parameters are described and discussed. A thorough sensitivity analysis of the method is carried out through simulations. No rigorous instrument calibration is needed for the presented method and it is therefore industrially tractable.
|
|
7. |
- Hagqvist, Petter, 1986-, et al.
(author)
-
Emissivity compensated spectral pyrometry for varying emissivity metallic measurands
- 2014
-
In: Measurement Science and Technology. - : IOP Publishing. - 0957-0233 .- 1361-6501. ; 25:2
-
Journal article (peer-reviewed)abstract
- A novel method for converting electromagnetic spectral radiance information into temperature measurements is presented. It allows for varying spectral emissivity of the metallic measurand during the course of the measurement. Such variations are due to, e. g., thermal oxidation or temperature dependent emissivity. Based on a requirement that emissivity changes with time and temperature are smooth, it is assumed that an emissivity estimate at one sample instance can be derived from the estimated emissivity found at the previous samples together with updated spectral information. This leads to successive recalculations of spectral emissivity together with corresponding temperature values. The proposed algorithm has been proven to give accurate temperature estimates from a measurement based on the data captured by a standard UV-Vis spectrophotometer even for an oxidizing Ti-6Al-4V specimen in a temperature range between 900 and 1400 K. The method however, is not limited to these wavelength or temperature ranges.
|
|
8. |
- Hagqvist, Petter, 1986-, et al.
(author)
-
Emissivity estimation for high temperature radiation pyrometry on Ti–6Al–4V
- 2013
-
In: Measurement. - : Elsevier BV. - 0263-2241 .- 1873-412X. ; 46:2, s. 871-880
-
Journal article (peer-reviewed)abstract
- The paper demonstrates a versatile procedure suitable for industrial implementation of temperature measurement on a hot titanium alloy. The driving force has been the need for an accurate temperature measurement during additive manufacturing using laser welding technology where Ti–6Al–4V-wire is melted. The challenges consider both industrial constraints and the varying emissivity of the surface. Measurements makes use of a narrow bandwidth spot radiation pyrometer and a calibration procedure for estimation of the surface temperature through spectral emissivity estimation. The theoretical results are validated through experiments. A number of difficulties in radiation temperature measurements for metals with varying surface properties are discussed; especially the case of surface oxidation. The uncertainty in temperature reading due to the uncertainty in the emissivity estimate is established along with a model that qualitatively describes surface oxidation. The procedure is expected to be useful for several manufacturing applications where it is important to control high temperatures.
|
|
9. |
- Jadidi, Aydin, Postdoktor, et al.
(author)
-
Beam Offset Detection in Laser Stake Welding of Tee Joints Using Machine Learning and Spectrometer Measurements
- 2022
-
In: Sensors. - : MDPI. - 1424-8220. ; 22:10
-
Journal article (peer-reviewed)abstract
- Laser beam welding offers high productivity and relatively low heat input and is one key enabler for efficient manufacturing of sandwich constructions. However, the process is sensitive to how the laser beam is positioned with regards to the joint, and even a small deviation of the laser beam from the correct joint position (beam offset) can cause severe defects in the produced part. With tee joints, the joint is not visible from top side, therefore traditional seam tracking methods are not applicable since they rely on visual information of the joint. Hence, there is a need for a monitoring system that can give early detection of beam offsets and stop the process to avoid defects and reduce scrap. In this paper, a monitoring system using a spectrometer is suggested and the aim is to find correlations between the spectral emissions from the process and beam offsets. The spectrometer produces high dimensional data and it is not obvious how this is related to the beam offsets. A machine learning approach is therefore suggested to find these correlations. A multi-layer perceptron neural network (MLPNN), support vector machine (SVM), learning vector quantization (LVQ), logistic regression (LR), decision tree (DT) and random forest (RF) were evaluated as classifiers. Feature selection by using random forest and non-dominated sorting genetic algorithm II (NSGAII) was applied before feeding the data to the classifiers and the obtained results of the classifiers are compared subsequently. After testing different offsets, an accuracy of 94% was achieved for real-time detection of the laser beam deviations greater than 0.9 mm from the joint center-line.
|
|
10. |
- Kisielewicz, Agnieszka, et al.
(author)
-
Hot-Wire Laser-Directed Energy Deposition : Process Characteristics and Benefits of Resistive Pre-Heating of the Feedstock Wire
- 2021
-
In: Metals. - : MDPI. - 2075-4701. ; 11:4, s. 1-25
-
Journal article (peer-reviewed)abstract
- This study investigates the influence of resistive pre-heating of the feedstock wire (here called hot-wire) on the stability of laser-directed energy deposition of Duplex stainless steel. Data acquired online during depositions as well as metallographic investigations revealed the process characteristic and its stability window. The online data, such as electrical signals in the pre-heating circuit and images captured from side-view of the process interaction zone gave insight on the metal transfer between the molten wire and the melt pool. The results show that the characteristics of the process, like laser-wire and wire-melt pool interaction, vary depending on the level of the wire pre-heating. In addition, application of two independent energy sources, laser beam and electrical power, allows fine-tuning of the heat input and increases penetration depth, with little influence on the height and width of the beads. This allows for better process stability as well as elimination of lack of fusion defects. Electrical signals measured in the hot-wire circuit indicate the process stability such that the resistive pre-heating can be used for in-process monitoring. The conclusion is that the resistive pre-heating gives additional means for controlling the stability and the heat input of the laser-directed energy deposition.
|
|