1. |
- Baken, Stijn, et al.
(author)
-
Characterisation of hydrous ferric oxides derived from iron-rich groundwaters and their contribution to the suspended sediment of streams
- 2013
-
In: Applied Geochemistry. - : Elsevier BV. - 0883-2927 .- 1872-9134. ; 39, s. 59-68
-
Journal article (peer-reviewed)abstract
- When Fe(II) bearing groundwaters surface in streams, particulate authigenic Fe-rich material is produced by oxidation. Such freshly precipitated Fe minerals may be transported as suspended sediment and have a profound impact on the fate of trace metals and nutrients in rivers. The objective of this study was to monitor changes in mineralogy and composition of authigenic material from its source to streams of increasing order. Groundwaters, surface waters, and suspended sediment in streams of different order were sampled in the Kleine Nete catchment (Belgium), a lowland with Fe-rich groundwaters (3.5-53.8 mg Fe/L; pH 6.3-6.9). Fresh authigenic material (>0.45 mu m) was produced by oxidising filtered (<0.45 mu m) groundwater and surface water. This material contained, on average, 44% Fe, and smaller concentrations of C, P, and Ca. Iron EXAFS (Extended X-ray Absorption Fine Structure) spectroscopy showed that the Fe was present as poorly crystalline hydrous ferric oxides with a structure similar to that of ferrihydrite. The Fe concentration in the suspended sediment samples decreased to 36-40% (stream order 2), and further to 18-26% (stream order 4 and 5). Conversely, the concentrations of organic C, Ca, Si, and trace metals increased with increasing stream order, suggesting mixing of authigenic material with suspended sediment from a different source. The Fe speciation in the suspended sediment was similar to that in fresh authigenic material, but more Fe-Fe interactions were observed, i.e. it was increasingly hydrolysed, suggesting ageing reactions. The suspended sediment in the streams of order 4 and 5 is estimated to contain between 31% and 59% of authigenic material, but more data are needed to refine this estimate. The authigenic material is an important sink for P in these streams which may alleviate the eutrophication risk in this catchment.
|
|
2. |
- Cornelis, Geert, et al.
(author)
-
Solubility and transport of Cr(III) in a historically contaminated soil – Evidence of a rapidly reacting dimeric Cr(III) organic matter complex
- 2017
-
In: Chemosphere. - : Elsevier BV. - 0045-6535 .- 1879-1298. ; 189, s. 709-716
-
Journal article (peer-reviewed)abstract
- Chromium is a common soil contaminant and, although it has been studied widely, questions about its speciation and dissolutions kinetics remain unanswered. We combined information from an irrigation experiment performed with intact soil columns with data from batch experiments to evaluate solubility and mobilization mechanisms of Cr(III) in a historically contaminated soil (>65 years). Particulate and colloidal Cr(III) forms dominated transport in this soil, but their concentrations were independent of irrigation intensity (2-20 mm h(-1)). Extended X-ray absorption fine structure (EXAFS) measurements indicated that Cr(III) associated with colloids and particles, and with the solid phase, mainly existed as dimeric hydrolyzed Cr(III) bound to natural organic matter. Dissolution kinetics of this species were fast (<= 1 day) at low pH (<3) and slightly slower (<= 5 days) at neutral pH. Furthermore, it proved possible to describe the solubility of the dimeric Cr(III) organic matter complex with a geochemical equilibrium model using only generic binding parameters, opening the way for use of geochemical models in risk assessments of Cr(III)-contaminated sites. (C) 2017 The Authors. Published by Elsevier Ltd.
|
|
3. |
- de Campos Pereira, Hugo, et al.
(author)
-
The Adsorption of Per- and Polyfluoroalkyl Substances (PFASs) onto Ferrihydrite Is Governed by Surface Charge
- 2020
-
In: Environmental Science and Technology. - : American Chemical Society (ACS). - 0013-936X .- 1520-5851. ; 54, s. 15722-15730
-
Journal article (peer-reviewed)abstract
- An improved quantitative and qualitative understanding of the interaction of per- and polyfluoroalkyl substances (PFASs) and short-range ordered Fe (hydr)oxides is crucial for environmental risk assessment in environments low in natural organic matter. Here, we present data on the pH-dependent sorption behavior of 12 PFASs onto ferrihydrite. The nature of the binding mechanisms was investigated by sulfur K-edge X-ray absorption near-edge structure (XANES) spectroscopy and by phosphate competition experiments. Sulfur K-edge XANES spectroscopy showed that the sulfur atom of the head group of the sulfonated PFASs retained an oxidation state of +V after adsorption. Furthermore, the XANES spectra did not indicate any involvement of inner-sphere surface complexes in the sorption process. Adsorption was inversely related to pH (p < 0.05) for all PFASs (i.e., C-3-C-5 and C-7-C-9 perfluorocarboxylates, C-4, C-6, and C-8 perfluorosulfonates, perfluorooctane sulfonamide, and 6:2 and 8:2 fluorotelomer sulfonates). This was attributed to the pH-dependent charge of the ferrihydrite surface, as reflected in the decrease of surface zeta-potential with increasing pH. The importance of surface charge for PFAS adsorption was further corroborated by the observation that the adsorption of PFASs decreased upon phosphate adsorption in a way that was consistent with the decrease in ferrihydrite zeta-potential. The results show that ferrihydrite can be an important sorbent for PFASs with six or more perfluorinated carbons in acid environments (pH <= 5), particularly when phosphate and other competitors are present in relatively low concentrations.
|
|
4. |
- Gustafsson, Jon Petter, 1964-, et al.
(author)
-
Chromium (III) and bismuth (III) complexation to organic matter : EXAFS Spectroscopy and equilibrium modeling
- 2013
-
In: Mineralogical magazine. - 0026-461X .- 1471-8022. ; 77:5, s. 1235-
-
Journal article (peer-reviewed)abstract
- The complexation of chromium(III) and bismuth(III) to organic matter was investigated by batch equilibrations with Suwannee River Fulvic Acid (SRFA) and with mor layer material (Risbergshöjden Oe). In the SRFA systems, 3 mM chromium(III) solutions were equilibrated with 9 g L-1 SRFA and equilibrated at different pH values ranging from 2 to 6. Characterization of the reaction products was made at MAX-Lab, Lund, Sweden, using Cr K-edge EXAFS spectroscopy at 5 989 eV. The spectra were interpreted using both conventional data treatment using EXAFSPAK and with wavelet transform (WT) analysis. The results show that chromium(III) formed monomeric organic complexes with SRFA. There was no evidence of polymerization with the exception of the particulate phase at pH 6, which was attributed to a limited extent of Cr(OH)3 formation.The mor layer material was equilibrated with chromium(III) and bismuth(III) solutions as a function of pH, time and competing ions (iron(III), aluminium(III), copper(II)). Again CrK-edge and Bi L3-edge EXAFS spectroscopy was used, at 5 989 and 13 419 eV. The experiments showed a predominance of monomeric organic complexes for chromium(III). The sorption of chromium(III) was pH-dependent and to some extent found to be influenced by competition from aluminium(III) and copper(II). Chromium(III) complexation was found to be very slow at pH < 4, and equilibration times of three months or longer were required to reach equilibrium under these conditions. Concerning bismuth(III), complexation was quicker and found to be very strong, with more than 94 % bound at pH 1.2 at a high bismuth(III) loading. EXAFS spectroscopy showed that two complexes were involved, one monomeric and one di- or trimeric, with the latter being predominant at higher pH values, although it was present already at pH 1.2. In the organic bismuth(III) complexes, the bismuth(III) octahedron was found to be strongly distorted, which implies strong binding to organic acid functional groups. The complexation of bismuth(III) remained essentially unchanged even in the presence of a potent competitor such as iron(III).The results from the spectroscopic investigation and from the quantitative solution data were used to calibrate new and improved complexation models for the Stockholm Humic (SHM) and the NICA-Donnan models. In the case of the Stockholm Humic Model, both complexes as found by EXAFS spectroscopy were considered explicitly; this ensured the model to predict minimum competition effects in agreement with the laboratory results.
|
|
5. |
- Gustafsson, Jon Petter, et al.
(author)
-
Chromium(III) complexation to natural organic matter : Mechanisms and modeling
- 2014
-
In: Environmental Science and Technology. - : American Chemical Society (ACS). - 0013-936X .- 1520-5851. ; 48:3, s. 1753-1761
-
Journal article (peer-reviewed)abstract
- Chromium is a common soil contaminant, and it often exists as chromium(III). However, limited information exists on the coordination chemistry and stability of chromium(III) complexes with natural organic matter (NOM). Here, the complexation of chromium(III) to mor layer material and to Suwannee River Fulvic Acid (SRFA) was investigated using EXAFS spectroscopy and batch experiments. The EXAFS results showed a predominance of monomeric chromium(III)-NOM complexes at low pH (<5), in which only Cr··C and Cr-O-C interactions were observed in the second coordination shell. At pH > 5 there were polynuclear chromium(III)-NOM complexes with Cr···Cr interactions at 2.98 Å and for SRFA also at 3.57 Å, indicating the presence of dimers (soil) and tetramers (SRFA). The complexation of chromium(III) to NOM was intermediate between that of iron(III) and aluminum(III). Chromium(III) complexation was slow at pH < 4: three months or longer were required to reach equilibrium. The results were used to constrain chromium-NOM complexation in the Stockholm Humic Model (SHM): a monomeric complex dominated at pH < 5, whereas a dimeric complex dominated at higher pH. The optimized constant for the monomeric chromium(III) complex was in between those of the iron(III) and aluminum(III) NOM complexes. Our study suggests that chromium(III)-NOM complexes are important for chromium speciation in many environments.
|
|
6. |
|
|
7. |
- Herting, Gunilla, et al.
(author)
-
Release of Si from Silicon, a Ferrosilicon (FeSi) Alloy and a Synthetic Silicate Mineral in Simulated Biological Media
- 2014
-
In: PLOS ONE. - : Public Library of Science (PLoS). - 1932-6203. ; 9:9, s. e107668-
-
Journal article (peer-reviewed)abstract
- Unique quantitative bioaccessibility data has been generated, and the influence of surface/material and test media characteristics on the elemental release process were assessed for silicon containing materials in specific synthetic body fluids at certain time periods at a fixed loading. The metal release test protocol, elaborated by the KTH team, has previously been used for classification, ranking, and screening of different alloys and metals. Time resolved elemental release of Si, Fe and Al from particles, sized less than 50 mm, of two grades of metallurgical silicon (high purity silicon, SiHG, low purity silicon, SiLG), an alloy (ferrosilicon, FeSi) and a mineral (aluminium silicate, AlSi) has been investigated in synthetic body fluids of varying pH, composition and complexation capacity, simple models of for example dermal contact and digestion scenarios. Individual methods for analysis of released Si (as silicic acid, Si(OH)(4)) in synthetic body fluids using GF-AAS were developed for each fluid including optimisation of solution pH and graphite furnace parameters. The release of Si from the two metallurgical silicon grades was strongly dependent on both pH and media composition with the highest release in pH neutral media. No similar effect was observed for the FeSi alloy or the aluminium silicate mineral. Surface adsorption of phosphate and lactic acid were believed to hinder the release of Si whereas the presence of citric acid enhanced the release as a result of surface complexation. An increased presence of Al and Fe in the material (low purity metalloid, alloy or mineral) resulted in a reduced release of Si in pH neutral media. The release of Si was enhanced for all materials with Al at their outermost surface in acetic media.
|
|
8. |
- Larsson, Maja, et al.
(author)
-
Vanadate complexation to ferrihydrite : X-ray absorption spectroscopy and CD-MUSIC modelling
- 2017
-
In: Environmental Chemistry. - : CSIRO Publishing. - 1448-2517 .- 1449-8979. ; 14:3, s. 141-150
-
Journal article (peer-reviewed)abstract
- The mobility of vanadium in the environment is influenced by sorption to metal (hydr)oxides, especially those containing iron. The aim of this study is to understand the adsorption behaviour of vanadium on poorly ordered (two-line) ferrihydrite (Fh). A further objective was to determine the binding mechanism of vanadate(V) to ferrihydrite surfaces in aqueous suspension to constrain the CD-MUSIC surface complexation model. Vanadium adsorption to ferrihydrite was evaluated by batch experiments which included series with different Fh-to-V ratios and pH values. Vanadate(V) adsorption was also evaluated in the presence of phosphate to compete with vanadate(V) for the available surface sites on ferrihydrite. In agreement with earlier studies, vanadate(V) was strongly adsorbed to ferrihydrite and the adsorption increased with decreasing pH. In the presence of phosphate, less vanadate(V) was adsorbed. Analysis by X-ray absorption near-edge structure spectroscopy revealed that the adsorbed vanadium was tetrahedral vanadate(V), VO4, regardless of whether vanadate(V) or vanadyl(IV) was added to the system. Spectra collected by extended X-ray absorption fine structure spectroscopy showed that vanadate(V) is bound primarily as an edge-sharing bidentate complex with VFe distances around 2.8 angstrom. Based on this information, a surface complexation model was set up in which three bidentate vanadate(V) complexes with different degrees of protonation were included. The model provided a satisfactory description of vanadate(V) adsorption over most of the pH and concentration ranges studied, also in the presence of competing phosphate ions.
|
|
9. |
- Löv, Åsa, et al.
(author)
-
Evaluating the ability of standardised leaching tests to predict metal(loid) leaching from intact soil columns using size-based elemental fractionation
- 2019
-
In: Chemosphere. - : Elsevier BV. - 0045-6535 .- 1879-1298. ; 222, s. 453-460
-
Journal article (peer-reviewed)abstract
- Laboratory-based leaching tests are frequently used for in situ risk assessments of contaminant leaching to groundwater and surface waters. This study evaluated the ability of three standardised leaching tests to assess leaching of lead (Pb), zinc (Zn), arsenic (As) and antimony (Sb) from four intact soil profiles, by considering particulate (0.45-8 mu m; percolation test), colloidal (10 kDa-0.45 mu m) and truly dissolved (<10 kDa) fractions of these elements. Deionised water was used as the percolation test leachant, while either deionised water or 1 mM CaCl2 was used in batch tests. Data from an irrigation experiment were used as reference. The results indicated that in percolation tests, leachate should be collected at a liquid:solid ratio (L/S) range of 2-10, instead of 0-0.5 or 0.5-2. Even at L/S = 2-10, the percolation test overestimated total Pb concentration, mainly because of greater mobilisation of particle-bound Pb, but appeared suitable for categorising soils into high/low risk with respect to mobilisation of particulate and colloidal contaminants. The batch test performed better with CaCl2 than with deionised water when standard membrane filtration (0.45 gm) was used, as the high Ca2+ concentration reduced colloidal mobilisation, avoiding overestimation of concentrations of elements such as Pb. However, the higher Ca2+ concentration and lower pH could result in overestimated concentrations of weakly sorbed elements, e.g. Zn. (C) 2019 The Authors. Published by Elsevier Ltd.
|
|
10. |
- Löv, Åsa, et al.
(author)
-
Particle- and colloid-facilitated Pb transport in four historically contaminated soils - Speciation and effect of irrigation intensity
- 2018
-
In: Applied Geochemistry. - : Elsevier BV. - 0883-2927. ; 96, s. 327-338
-
Journal article (peer-reviewed)abstract
- Due to the low solubility of lead (Pb) in many soils, colloidal and particulate transport may have large effects on Pb leaching. However, the role of colloidal and particulate transport varies considerably between soils and the mechanisms controlling mobilisation are complex and poorly known. Furthermore, increased frequency of high-intensity rainfall events is expected in some parts of Europe and North America in response to climate change, which might increase the mobilisation of particles and colloids. In this work, we investigated transport of particulate ( > 0.45 mu m), colloidal (10 kDa-0.45 mu m) and truly dissolved ( < 10 kDa) Pb in an irrigation experiment on intact soil columns from four historically contaminated soils. We also investigated the effect of irrigation intensity (2-20 mmh(-1)) on Pb leaching in these fractions. The mechanism binding Pb on particles and colloids was evaluated by extended X-ray absorption fine structure (EXAFS) spectroscopy and geochemical modelling. A 10-fold increase in irrigation intensity brought about at most a three-fold change in leached particulate and colloidal Pb concentrations. In contrast, the fraction of leached Pb associated with particles and colloids varied by one order of magnitude between soils. Hence, the results suggest that it is more important to consider soil type than potential future increases in rainfall. For one soil with high concentrations of both arsenic (As) and Pb, geochemical modelling indicated that mimetite, Pb-5(AsO4)(3)Cl(s), was the major Pb species in the colloidal and particulate fractions. For the other three soils, EXAFS of Pb on isolated particles and colloids indicated that ferrihydrite was a major phase-sorbing Pb and this was supported by geochemical equilibrium modelling. Thus geochemical modelling can be used to indicate the speciation of Pb in particles and colloids leached in intact soils.
|
|