| 1. |
- Elihn, Karine, et al.
(author)
-
Air quality impacts of a large waste fire in Stockholm, Sweden
- 2023
-
In: Atmospheric Environment. - : Elsevier BV. - 1352-2310 .- 1873-2844. ; 315
-
Journal article (peer-reviewed)abstract
- Fires in waste facilities are a common occurrence. Since many waste facilities are located adjacent to densely populated areas, these fires could potentially expose large populations to the emitted pollutants. However, at the moment there are only few field studies investigating the impact of waste fire emissions on air quality since the unpredictable nature of these events makes them challenging to capture. This study investigated the impact of a large and persistent un-prescribed fire in a waste storage facility in Stockholm county, Sweden, on the local air quality of two residential areas in close proximity to the fire. In-situ measurements of particulate matter, black carbon and nitrogen oxide concentrations were conducted both during open burning and after the fire was fully covered. In addition, filter samples were collected for offline analysis of organic composition, metal content and toxicity. Strongly increased concentrations of PM10, PM2.5 and black carbon were found during the open burning period, especially when the wind was coming from the direction of the fire. In addition, elevated concentrations of particulate heavy metals and polycyclic aromatic hydrocarbons were observed in the air during the open burning period. These results show that waste fires can have a strong impact on the air quality of nearby residential areas.
|
|
| 2. |
|
|
| 3. |
- Karlsson, Hanna L., et al.
(author)
-
Health hazards of particles in additive manufacturing : a cross-disciplinary study on reactivity, toxicity and occupational exposure to two nickel-based alloys
- 2023
-
In: Scientific Reports. - : Springer Nature. - 2045-2322. ; 13:1
-
Journal article (peer-reviewed)abstract
- The increasing use of additive manufacturing (AM) techniques (e.g., 3D-printing) offers many advantages but at the same time presents some challenges. One concern is the possible exposure and health risk related to metal containing particles of different sizes. Using the nickel-based alloys Hastelloy X (HX) and Inconel 939 (IN939) as a case, the aim of this cross-disciplinary study was to increase the understanding on possible health hazards and exposure. This was done by performing in-depth characterization of virgin, reused and condensate powders, testing in vitro toxicity (cytotoxicity, genotoxicity, oxidative stress), and measuring occupational airborne exposure. The results showed limited metal release from both HX and IN939, and slightly different surface composition of reused compared to virgin powders. No or small effects on the cultured lung cells were observed when tested up to 100 µg/mL. Particle background levels in the printing facilities were generally low, but high transient peaks were observed in relation to sieving. Furthermore, during post processing with grinding, high levels of nanoparticles (> 100,000 particles/cm3) were noted. Urine metal levels in AM operators did not exceed biomonitoring action limits. Future studies should focus on understanding the toxicity of the nanoparticles formed during printing and post-processing.
|
|
| 4. |
- Vallabani, N. V. Srikanth, et al.
(author)
-
Toxicity and health effects of ultrafine particles : Towards an understanding of the relative impacts of different transport modes
- 2023
-
In: Environmental Research. - : Elsevier BV. - 0013-9351 .- 1096-0953. ; 231
-
Research review (peer-reviewed)abstract
- Exposure to particulate matter (PM) has been associated with a wide range of adverse health effects, but it is still unclear how particles from various transport modes differ in terms of toxicity and associations with different human health outcomes. This literature review aims to summarize toxicological and epidemiological studies of the effect of ultrafine particles (UFPs), also called nanoparticles (NPs, <100 nm), from different transport modes with a focus on vehicle exhaust (particularly comparing diesel and biodiesel) and non-exhaust as well as particles from shipping (harbor), aviation (airport) and rail (mainly subway/underground). The review includes both particles collected in laboratory tests and the field (intense traffic environments or collected close to harbor, airport, and in subway). In addition, epidemiological studies on UFPs are reviewed with special attention to studies aimed at distinguishing the effects of different transport modes. Results from toxicological studies indicate that both fossil and biodiesel NPs show toxic effects. Several in vivo studies show that inhalation of NPs collected in traffic environments not only impacts the lung, but also triggers cardiovascular effects as well as negative impacts on the brain, although few studies compared NPs from different sources. Few studies were found on aviation (airport) NPs, but the available results suggest similar toxic effects as traffic-related particles. There is still little data related to the toxic effects linked to several sources (shipping, road and tire wear, subway NPs), but in vitro results highlighted the role of metals in the toxicity of subway and brake wear particles. Finally, the epidemiological studies emphasized the current limited knowledge of the health impacts of source-specific UFPs related to different transport modes. This review discusses the necessity of future research for a better understanding of the relative potencies of NPs from different transport modes and their use in health risk assessment.
|
|
| 5. |
- Vallabani, N. V. Srikanth, et al.
(author)
-
Toxicity evaluation of particles formed during 3D-printing : Cytotoxic, genotoxic, and inflammatory response in lung and macrophage models
- 2022
-
In: Toxicology. - : Elsevier BV. - 0300-483X .- 1879-3185. ; 467
-
Journal article (peer-reviewed)abstract
- Additive manufacturing (AM) or "3D-printing" is a ground-breaking technology that enables the production of complex 3D parts. Its rapid growth calls for immediate toxicological investigations of possible human exposures in order to estimate occupational health risks. Several laser-based powder bed fusion AM techniques are available of which many use metal powder in the micrometer range as feedstock. Large energy input from the laser on metal powders generates several by-products, like spatter and condensate particles. Due to often altered physicochemical properties and composition, spatter and condensate particles can result in different toxicological responses compared to the original powder particles. The toxicity of such particles has, however, not yet been investigated. The aim of the present study was to investigate the toxicity of condensate/spatter particles formed and collected upon selective laser melting (SLM) printing of metal alloy powders, including a nickel-chromiumbased superalloy (IN939), a nickel-based alloy (Hastelloy X, HX), a high-strength maraging steel (18Ni300), a stainless steel (316L), and a titanium alloy (Ti6Al4V). Toxicological endpoints investigated included cytotoxicity, generation of reactive oxygen species (ROS), genotoxicity (comet and micronucleus formation), and inflammatory response (cytokine/chemokine profiling) following exposure of human bronchial epithelial cells (HBEC) or monocytes/macrophages (THP-1). The results showed no or minor cytotoxicity in the doses tested (10 100 mu g/mL). Furthermore, no ROS generation or formation of micronucleus was observed in the HBEC cells. However, an increase in DNA strand breaks (detected by comet assay) was noted in cells exposed to HX, IN939, and Ti6Al4V, whereas no evident release of pro-inflammatory cytokine was observed from macrophages. Particle and surface characterization showed agglomeration in solution and different surface oxide compositions compared to the nominal bulk content. The extent of released nickel was small and related to the nickel content of the surface oxides, which was largely different from the bulk content. This may explain the limited toxicity found despite the high Ni bulk content of several powders. Taken together, this study suggests relatively low acute toxicity of condensates/spatter particles formed during SLM-printing using IN939, HX, 18Ni300, 316L, and Ti6Al4V as original metal powders.
|
|
| 6. |
- Wang, Xuying, et al.
(author)
-
Bioaccessibility and reactivity of alloy powders used in powder bed fusion additive manufacturing
- 2021
-
In: Materialia. - : Elsevier. - 2589-1529. ; 19, s. 1-10
-
Journal article (peer-reviewed)abstract
- Exposure to metal particles via the inhalation route unavoidably takes place at occupational settings during additive manufacturing of metals and alloys. This calls for investigations on possible adverse health effects. This study focuses on virgin and reused powders of three iron- and nickel-based alloy powders (316L, IN718, 18Ni300) widely used in additive manufacturing, and dust powder of 18Ni300 generated during laser melting. Investigations were performed from a physico-chemical and toxicological perspective assessing their bioaccessibility in artificial lysosomal fluid (ALF, simulating lung exposure to respirable particles), corrosion behavior, surface morphology and composition, microstructure, hydrodynamic size distribution in ALF, and in-vitro toxicity towards cultured human lung cells. Less than 1 % of the powder mass was dissolved from the passive alloys (316L, IN718) under simulated physiological conditions (pH 4.5, 37°C, 24 h), whereas the 18Ni300 iron-nickel alloy showed an active behavior and dissolved completely. Reused powders of 18Ni300 and IN718 showed no, or only minor, differences in surface oxide composition, metal release pattern, and corrosion behavior compared with virgin powders. After reuse, the 316L powder showed an enrichment of manganese within the outermost surface, an increased corrosion current, increased amounts of released iron and an increased fraction of particles with ferritic microstructure, which increased the extent of particle aggregation. All powders showed low, or negligible, cytotoxic potency and reactive oxygen species formation. Powder bed fusion using laser melting can hence affect the chemical, physical, and surface properties of non-fused powders, which, if reused, could influence the properties of the printed part.
|
|
