| 1. |
- Li, Xiane, et al.
(author)
-
Mapping the energy level alignment at donor/acceptor interfaces in non-fullerene organic solar cells
- 2022
-
In: Nature Communications. - : Nature Portfolio. - 2041-1723. ; 13:1
-
Journal article (peer-reviewed)abstract
- Energy level alignment (ELA) at donor-acceptor heterojunctions is of vital importance yet largely undetermined in organic solar cells. Here, authors determine the heterojunction ELA with (mono) layer-by-layer precision to understand the co-existence of efficient charge. Energy level alignment (ELA) at donor (D) -acceptor (A) heterojunctions is essential for understanding the charge generation and recombination process in organic photovoltaic devices. However, the ELA at the D-A interfaces is largely underdetermined, resulting in debates on the fundamental operating mechanisms of high-efficiency non-fullerene organic solar cells. Here, we systematically investigate ELA and its depth-dependent variation of a range of donor/non-fullerene-acceptor interfaces by fabricating and characterizing D-A quasi bilayers and planar bilayers. In contrast to previous assumptions, we observe significant vacuum level (VL) shifts existing at the D-A interfaces, which are demonstrated to be abrupt, extending over only 1-2 layers at the heterojunctions, and are attributed to interface dipoles induced by D-A electrostatic potential differences. The VL shifts result in reduced interfacial energetic offsets and increased charge transfer (CT) state energies which reconcile the conflicting observations of large energy level offsets inferred from neat films and large CT energies of donor - non-fullerene-acceptor systems.
|
|
| 2. |
- Zhang, Qilun, 1992-, et al.
(author)
-
Natural Product Betulin-Based Insulating Polymer Filler in Organic Solar Cells
- 2022
-
In: Solar RRL. - : Wiley. - 2367-198X. ; 6:9
-
Journal article (peer-reviewed)abstract
- Introduction of filler materials into organic solar cells (OSCs) are a promising strategy to improve device performance and thermal/mechanical stability. However, the complex interactions between the state-of-the-art OSC materials and filler require careful selection of filler materials and OSC fabrication to achieve lower cost and improved performance. In this work, the introduction of a natural product betulin-based insulating polymer as filler in various OSCs is investigated. Donor–acceptor–insulator ternary OSCs are developed with improved open-circuit voltage (Voc) due to decreased trap-assisted recombination. Furthermore, filler-induced vertical phase separation due to mismatched surface energy can strongly affect charge collection at the bottom interface and limit the filler ratio. A quasi-bilayer strategy is used in all-polymer systems to circumvent this problem. Herein, the variety of filler materials in OSCs to biomass is broadened, and the filler strategy is made a feasible and promising strategy toward highly efficient, eco, and low-cost OSCs.
|
|
| 3. |
- Li, Qifan, et al.
(author)
-
A Highly Conductive n-Type Conjugated Polymer Synthesized in Water
- 2024
-
In: Journal of the American Chemical Society. - : AMER CHEMICAL SOC. - 0002-7863 .- 1520-5126.
-
Journal article (peer-reviewed)abstract
- Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is a benchmark hole-transporting (p-type) polymer that finds applications in diverse electronic devices. Most of its success is due to its facile synthesis in water, exceptional processability from aqueous solutions, and outstanding electrical performance in ambient. Applications in fields like (opto-)electronics, bioelectronics, and energy harvesting/storage devices often necessitate the complementary use of both p-type and n-type (electron-transporting) materials. However, the availability of n-type materials amenable to water-based polymerization and processing remains limited. Herein, we present a novel synthesis method enabling direct polymerization in water, yielding a highly conductive, water-processable n-type conjugated polymer, namely, poly[(2,2 '-(2,5-dihydroxy-1,4-phenylene)diacetic acid)-stat-3,7-dihydrobenzo[1,2-b:4,5-b ']difuran-2,6-dione] (PDADF), with remarkable electrical conductivity as high as 66 S cm(-1), ranking among the highest for n-type polymers processed using green solvents. The new n-type polymer PDADF also exhibits outstanding stability, maintaining 90% of its initial conductivity after 146 days of storage in air. Our synthetic approach, along with the novel polymer it yields, promises significant advancements for the sustainable development of organic electronic materials and devices.
|
|
| 4. |
- Liu, Tiefeng, et al.
(author)
-
Ground-state electron transfer in all-polymer donor:acceptor blends enables aqueous processing of water-insoluble conjugated polymers
- 2023
-
In: Nature Communications. - : NATURE PORTFOLIO. - 2041-1723. ; 14:1
-
Journal article (peer-reviewed)abstract
- Water-based conductive inks are vital for the sustainable manufacturing and widespread adoption of organic electronic devices. Traditional methods to produce waterborne conductive polymers involve modifying their backbone with hydrophilic side chains or using surfactants to form and stabilize aqueous nanoparticle dispersions. However, these chemical approaches are not always feasible and can lead to poor material/device performance. Here, we demonstrate that ground-state electron transfer (GSET) between donor and acceptor polymers allows the processing of water-insoluble polymers from water. This approach enables macromolecular charge-transfer salts with 10,000x higher electrical conductivities than pristine polymers, low work function, and excellent thermal/solvent stability. These waterborne conductive films have technological implications for realizing high-performance organic solar cells, with efficiency and stability superior to conventional metal oxide electron transport layers, and organic electrochemical neurons with biorealistic firing frequency. Our findings demonstrate that GSET offers a promising avenue to develop water-based conductive inks for various applications in organic electronics. Chemical approaches to improve aqueous dispersions of conjugated polymers are limited by the feasibility of modifying the backbone or lead to poor performance. Here, Liu et al. show that ground-state electron transfer in donor:acceptor blends aids aqueous dispersion, for high conductivity and solubility.
|
|
| 5. |
- Wang, Chuan Fei, et al.
(author)
-
Thermal-annealing effects on energy level alignment at organic heterojunctions and corresponding voltage losses in all-polymer solar cells
- 2020
-
In: Nano Energy. - : ELSEVIER. - 2211-2855 .- 2211-3282. ; 72
-
Journal article (peer-reviewed)abstract
- Matched energy level alignment is a key requirement for efficient organic devices such as organic light-emitting diodes, photovoltaics, and field-effect transistors. The effect of thermal stress/annealing on energy level alignment and related properties of the devices are less discussed compared to the extensively explored effect on morphology and corresponding device performance. Here all polymer solar cells (all-PSCs) are employed to study thermal annealing effects on energy level alignment and the corresponding effect on the device properties of the all-PSCs. It is found that optimized energy level alignment can be achieved by thermal annealing. An interface dipole layer at the donor/acceptor interface is introduced by energy level realignment that assists charge generation by reducing geminate recombination so that the voltage loss is dramatically reduced, improving the performance of the all-PSCs.
|
|
| 6. |
- Zhang, Qilun, 1992-, et al.
(author)
-
Industrial Kraft Lignin Based Binary Cathode Interface Layer Enables Enhanced Stability in High Efficiency Organic Solar Cells
- 2023
-
In: Advanced Materials. - : WILEY-V C H VERLAG GMBH. - 0935-9648 .- 1521-4095.
-
Journal article (peer-reviewed)abstract
- Herein, a binary cathode interface layer (CIL) strategy based on the industrial solvent fractionated LignoBoost kraft lignin (KL) is adopted for fabrication of organic solar cells (OSCs). The uniformly distributed phenol moieties in KL enable it to easily form hydrogen bonds with commonly used CIL materials, i.e., bathocuproine (BCP) and PFN-Br, resulting in binary CILs with tunable work function (WF). This work shows that the binary CILs work well in OSCs with large KL ratio compatibility, exhibiting equivalent or even higher efficiency to the traditional CILs in state of art OSCs. In addition, the combination of KL and BCP significantly enhanced OSC stability, owing to KL blocking the reaction between BCP and nonfullerene acceptors (NFAs). This work provides a simple and effective way to achieve high-efficient OSCs with better stability and sustainability by using wood-based materials. This work introduces industrial solvent fractionated LignoBoost kraft lignin (KL) in highly efficient organic solar cells (OSCs) by binary cathode interface layer (CIL) strategy, which can significantly improve the stability of both binary and ternary photoactive layer (PAL) OSC, owing to the passivation of diffusion and reaction between bathocuproine (BCP) and nonfullerene acceptors (NFAs). The results combine sustainable wood-based material with classic interface materials in advance NFA-OSCs.image
|
|
| 7. |
- Beket, Gulzada, et al.
(author)
-
Overcoming the voltage losses caused by the acceptor-based interlayer in laminated indoor OPVs
- 2023
-
In: SMARTMAT. - : WILEY. - 2766-8525.
-
Journal article (peer-reviewed)abstract
- Harvesting indoor light to power electronic devices for the Internet of Things has become an application scenario for emerging photovoltaics, especially utilizing organic photovoltaics (OPVs). Combined liquid- and solid-state processing, such as printing and lamination used in industry for developing indoor OPVs, also provides a new opportunity to investigate the device structure, which is otherwise hardly possible based on the conventional approach due to solvent orthogonality. This study investigates the impact of fullerene-based acceptor interlayer on the performance of conjugated polymer-fullerene-based laminated OPVs for indoor applications. We observe open-circuit voltage (V-OC) loss across the interface despite this arrangement being presumed to be ideal for optimal device performance. Incorporating insulating organic components such as polyethyleneimine (PEI) or polystyrene (PS) into fullerene interlayers decreases the work function of the cathode, leading to better energy level alignment with the active layer (AL) and reducing the V-OC loss across the interface. Neutron reflectivity studies further uncover two different mechanisms behind the V-OC increase upon the incorporation of these insulating organic components. The self-organized PEI layer could hinder the transfer of holes from the AL to the acceptor interlayer, while the gradient distribution of the PS-incorporated fullerene interlayer eliminates the thermalization losses. This work highlights the importance of structural dynamics near the extraction interfaces in OPVs and provides experimental demonstrations of interface investigation between solution-processed cathodic fullerene layer and bulk heterojunction AL.
|
|
| 8. |
- Kuang, Chaoyang, et al.
(author)
-
Switchable Broadband Terahertz Absorbers Based on Conducting Polymer-Cellulose Aerogels
- 2023
-
In: Advanced Science. - : WILEY. - 2198-3844.
-
Journal article (peer-reviewed)abstract
- Terahertz (THz) technologies provide opportunities ranging from calibration targets for satellites and telescopes to communication devices and biomedical imaging systems. A main component will be broadband THz absorbers with switchability. However, optically switchable materials in THz are scarce and their modulation is mostly available at narrow bandwidths. Realizing materials with large and broadband modulation in absorption or transmission forms a critical challenge. This study demonstrates that conducting polymer-cellulose aerogels can provide modulation of broadband THz light with large modulation range from ≈ 13% to 91% absolute transmission, while maintaining specular reflection loss < −30 dB. The exceptional THz modulation is associated with the anomalous optical conductivity peak of conducting polymers, which enhances the absorption in its oxidized state. The study also demonstrates the possibility to reduce the surface hydrophilicity by simple chemical modifications, and shows that broadband absorption of the aerogels at optical frequencies enables de-frosting by solar-induced heating. These low-cost, aqueous solution-processable, sustainable, and bio-friendly aerogels may find use in next-generation intelligent THz devices.
|
|
| 9. |
- Li, Xiane, et al.
(author)
-
Pinning energies of organic semiconductors in high-efficiency organic solar cells
- 2023
-
In: JOURNAL OF SEMICONDUCTORS. - : IOP Publishing Ltd. - 1674-4926 .- 2058-6140. ; 44:3
-
Journal article (peer-reviewed)abstract
- With the emergence of new materials for high-efficiency organic solar cells (OSCs), understanding and finetuning the interface energetics become increasingly important. Precise determination of the so-called pinning energies, one of the critical characteristics of the material to predict the energy level alignment (ELA) at either electrode/organic or organic/organic interfaces, are urgently needed for the new materials. Here, pinning energies of a wide variety of newly developed donors and non-fullerene acceptors (NFAs) are measured through ultraviolet photoelectron spectroscopy. The positive pinning energies of the studied donors and the negative pinning energies of NFAs are in the same energy range of 4.3-4.6 eV, which follows the design rules developed for fullerene-based OSCs. The ELA for metal/organic and inorganic/organic interfaces follows the predicted behavior for all of the materials studied. For organic-organic heterojunctions where both the donor and the NFA feature strong intramolecular charge transfer, the pinning energies often underestimate the experimentally obtained interface vacuum level shift, which has consequences for OSC device performance.
|
|
| 10. |
- Liao, Mingna, et al.
(author)
-
Cellulose-Based Radiative Cooling and Solar Heating Powers Ionic Thermoelectrics
- 2023
-
In: Advanced Science. - : WILEY. - 2198-3844. ; 10:8
-
Journal article (peer-reviewed)abstract
- Cellulose opens for sustainable materials suitable for radiative cooling thanks to inherent high thermal emissivity combined with low solar absorptance. When desired, solar absorptance can be introduced by additives such as carbon black. However, such materials still shows high thermal emissivity and therefore performs radiative cooling that counteracts the heating process if exposed to the sky. Here, this is addressed by a cellulose-carbon black composite with low mid-infrared (MIR) emissivity and corresponding suppressed radiative cooling thanks to a transparent IR-reflecting indium tin oxide coating. The resulting solar heater provides opposite optical properties in both the solar and thermal ranges compared to the cooler material in the form of solar-reflecting electrospun cellulose. Owing to these differences, exposing the two materials to the sky generated spontaneous temperature differences, as used to power an ionic thermoelectric device in both daytime and nighttime. The study characterizes these effects in detail using solar and sky simulators and through outdoor measurements. Using the concept to power ionic thermoelectric devices shows thermovoltages of >60 mV and 10 degrees C temperature differences already at moderate solar irradiance of approximate to 400 W m(-2).
|
|
