1. |
- Almeida, Cristiane G., et al.
(author)
-
Photocatalytic hydrogen production with visible light over Mo and Cr-doped BiNb(Ta)O-4
- 2014
-
In: International journal of hydrogen energy. - : Elsevier BV. - 0360-3199 .- 1879-3487. ; 39:3, s. 1220-1227
-
Journal article (peer-reviewed)abstract
- In the present work, we prepared pure and Cr(III) and Mo(V)-doped BiNbO4 and BiTaO4 by the citrate method. Pure BiNbO4 and BiTaO4 were obtained in triclinic phase at 600 degrees C and 800 degrees C, respectively. The metal doping influenced strongly the crystal structure as well as the photocatalytic activity of the oxides. The XRD data could prove that the Mo(V) doping induces the orthorhombic phase, while the Cr(III) doping favors the triclinic phase for both oxides. Metal doping also modified the photosensitivity of the oxides, extending the absorption toward the visible light region. The photocatalytic activity in water splitting under visible light irradiation was evaluated by monitoring the H-2, CO2 and CO evolution. The results showed that Cr(III)-doped BiTaO4 and BiNbO4, in general, are more selective for hydrogen production, while Mo(V)-doped materials are more selective for CO2 generation. Comparing the photocatalytic activity of BiTaO4 and BiNbO4, the former shows higher activity for hydrogen production as well as for CO2 generation, specially when the concentration was 2% in Cr(III) and Mo(V), respectively. Those results are in agreement with the computational study to access the effect of doping on the electronic structure. For Mo(V)-doped materials a negligible change of conduction band minimum potential was found, indicating that there might be no improvement on the reduction power of the material following the substitutional doping. In Cr(III)-doped BiNbO4 there is a slight shift of the CBM potential increasing a little bit the reduction power. However, the effect is much stronger in the Cr(III)-doped BiTaO4.
|
|
2. |
- Householder, John Ethan, et al.
(author)
-
One sixth of Amazonian tree diversity is dependent on river floodplains
- 2024
-
In: NATURE ECOLOGY & EVOLUTION. - 2397-334X.
-
Journal article (peer-reviewed)abstract
- Amazonia's floodplain system is the largest and most biodiverse on Earth. Although forests are crucial to the ecological integrity of floodplains, our understanding of their species composition and how this may differ from surrounding forest types is still far too limited, particularly as changing inundation regimes begin to reshape floodplain tree communities and the critical ecosystem functions they underpin. Here we address this gap by taking a spatially explicit look at Amazonia-wide patterns of tree-species turnover and ecological specialization of the region's floodplain forests. We show that the majority of Amazonian tree species can inhabit floodplains, and about a sixth of Amazonian tree diversity is ecologically specialized on floodplains. The degree of specialization in floodplain communities is driven by regional flood patterns, with the most compositionally differentiated floodplain forests located centrally within the fluvial network and contingent on the most extraordinary flood magnitudes regionally. Our results provide a spatially explicit view of ecological specialization of floodplain forest communities and expose the need for whole-basin hydrological integrity to protect the Amazon's tree diversity and its function.
|
|
3. |
- Luize, Bruno Garcia, et al.
(author)
-
Geography and ecology shape the phylogenetic composition of Amazonian tree communities
- 2024
-
In: JOURNAL OF BIOGEOGRAPHY. - 0305-0270 .- 1365-2699.
-
Journal article (peer-reviewed)abstract
- Aim: Amazonia hosts more tree species from numerous evolutionary lineages, both young and ancient, than any other biogeographic region. Previous studies have shown that tree lineages colonized multiple edaphic environments and dispersed widely across Amazonia, leading to a hypothesis, which we test, that lineages should not be strongly associated with either geographic regions or edaphic forest types. Location: Amazonia. Taxon: Angiosperms (Magnoliids; Monocots; Eudicots). Methods: Data for the abundance of 5082 tree species in 1989 plots were combined with a mega-phylogeny. We applied evolutionary ordination to assess how phylogenetic composition varies across Amazonia. We used variation partitioning and Moran's eigenvector maps (MEM) to test and quantify the separate and joint contributions of spatial and environmental variables to explain the phylogenetic composition of plots. We tested the indicator value of lineages for geographic regions and edaphic forest types and mapped associations onto the phylogeny. Results: In the terra firme and v & aacute;rzea forest types, the phylogenetic composition varies by geographic region, but the igap & oacute; and white-sand forest types retain a unique evolutionary signature regardless of region. Overall, we find that soil chemistry, climate and topography explain 24% of the variation in phylogenetic composition, with 79% of that variation being spatially structured (R-2 = 19% overall for combined spatial/environmental effects). The phylogenetic composition also shows substantial spatial patterns not related to the environmental variables we quantified (R-2 = 28%). A greater number of lineages were significant indicators of geographic regions than forest types. Main Conclusion: Numerous tree lineages, including some ancient ones (>66 Ma), show strong associations with geographic regions and edaphic forest types of Amazonia. This shows that specialization in specific edaphic environments has played a long-standing role in the evolutionary assembly of Amazonian forests. Furthermore, many lineages, even those that have dispersed across Amazonia, dominate within a specific region, likely because of phylogenetically conserved niches for environmental conditions that are prevalent within regions.
|
|
4. |
- ter Steege, Hans, et al.
(author)
-
Mapping density, diversity and species-richness of the Amazon tree flora
- 2023
-
In: COMMUNICATIONS BIOLOGY. - 2399-3642. ; 6:1
-
Journal article (peer-reviewed)abstract
- Using 2.046 botanically-inventoried tree plots across the largest tropical forest on Earth, we mapped tree species-diversity and tree species-richness at 0.1-degree resolution, and investigated drivers for diversity and richness. Using only location, stratified by forest type, as predictor, our spatial model, to the best of our knowledge, provides the most accurate map of tree diversity in Amazonia to date, explaining approximately 70% of the tree diversity and species-richness. Large soil-forest combinations determine a significant percentage of the variation in tree species-richness and tree alpha-diversity in Amazonian forest-plots. We suggest that the size and fragmentation of these systems drive their large-scale diversity patterns and hence local diversity. A model not using location but cumulative water deficit, tree density, and temperature seasonality explains 47% of the tree species-richness in the terra-firme forest in Amazonia. Over large areas across Amazonia, residuals of this relationship are small and poorly spatially structured, suggesting that much of the residual variation may be local. The Guyana Shield area has consistently negative residuals, showing that this area has lower tree species-richness than expected by our models. We provide extensive plot meta-data, including tree density, tree alpha-diversity and tree species-richness results and gridded maps at 0.1-degree resolution. A study mapping the tree species richness in Amazonian forests shows that soil type exerts a strong effect on species richness, probably caused by the areas of these forest types. Cumulative water deficit, tree density and temperature seasonality affect species richness at a regional scale.
|
|
5. |
- Araujo, Rafael B., et al.
(author)
-
Assessing Electrochemical Properties of Polypyridine and Polythiophene for Prospective Application in Sustainable Organic Batteries
- 2017
-
In: Physical Chemistry, Chemical Physics - PCCP. - 1463-9076 .- 1463-9084. ; 19:4, s. 3307-3314
-
Journal article (peer-reviewed)abstract
- Conducting polymers are being considered promising candidates for sustainable organic batteries mainly due to their fast electron transport properties and high recyclability. In this work, key properties of polythiophene and polypyridine have been assessed through a combined theoretical and experimental study focusing on such applications. A theoretical protocol has been developed to calculate redox potentials in solution within the framework of the density functional theory and using continuous solvation models. Here, the evolution of the electrochemical properties of solvated oligomers as a function of the length of the chain is analyzed and then the polymer properties are estimated via linear regressions using ordinary least square. The predicted values were verified against our electrochemical experiments. This protocol can now be employed to screen a large database of compounds in order to identify organic electrodes with superior properties.
|
|
6. |
- Araujo, Rafael B., et al.
(author)
-
Assessing the electrochemical properties of polypyridine and polythiophene for prospective applications in sustainable organic batteries
- 2017
-
In: Physical Chemistry, Chemical Physics - PCCP. - : Royal Society of Chemistry. - 1463-9076 .- 1463-9084. ; 19:4, s. 3307-3314
-
Journal article (peer-reviewed)abstract
- Conducting polymers are being considered promising candidates for sustainable organic batteries mainly due to their fast electron transport properties and high recyclability. In this work, the key properties of polythiophene and polypyridine have been assessed through a combined theoretical and experimental study focusing on such applications. A theoretical protocol has been developed to calculate redox potentials in solution within the framework of the density functional theory and using continuous solvation models. Here, the evolution of the electrochemical properties of solvated oligomers as a function of the length of the chain is analyzed and then the polymer properties are estimated via linear regressions using ordinary least square. The predicted values were verified against our electrochemical experiments. This protocol can now be employed to screen a large database of compounds in order to identify organic electrodes with superior properties.
|
|
7. |
- Araujo, Rafael B., et al.
(author)
-
Designing strategies to tune reduction potential of organic molecules for sustainable high capacity batteries application
- 2017
-
In: Journal of Materials Chemistry A. - 2050-7488 .- 2050-7496. ; 5:9, s. 4430-4454
-
Journal article (peer-reviewed)abstract
- Organic compounds evolve as a promising alternative to the currently used inorganic materials in rechargeable batteries due to their low-cost, environmentally friendliness and flexibility. One of the strategies to reach acceptable energy densities and to deal with the high solubility of known organic compounds is to combine small redox active molecules, acting as capacity carrying centres, with conducting polymers. Following this strategy, it is important to achieve redox matching between the chosen molecule and the polymer backbone. Here, a synergetic approach combining theory and experiment has been employed to investigate this strategy. The framework of density functional theory connected with the reaction field method has been applied to predict the formal potential of 137 molecules and identify promising candidates for the referent application. The effects of including different ring types, e.g. fused rings or bonded rings, heteroatoms, [small pi] bonds, as well as carboxyl groups on the formal potential, has been rationalized. Finally, we have identified a number of molecules with acceptable theoretical capacities that show redox matching with thiophene-based conducting polymers which, hence, are suggested as pendent groups for the development of conducting redox polymer based electrode materials.
|
|
8. |
- Araujo, Rafael B., et al.
(author)
-
Designing strategies to tune reduction potential of organic molecules for sustainable high capacity battery application
- 2017
-
In: Journal of Materials Chemistry A. - : Royal Society of Chemistry. - 2050-7488 .- 2050-7496. ; 5:9, s. 4430-4454
-
Journal article (peer-reviewed)abstract
- Organic compounds evolve as a promising alternative to currently used inorganic materials in rechargeable batteries due to their low-cost, environmental friendliness and flexibility. One of the strategies to reach acceptable energy densities and to deal with the high solubility of known organic compounds is to combine small redox active molecules, acting as capacity carrying centres, with conducting polymers. Following this strategy, it is important to achieve redox matching between the chosen molecule and the polymer backbone. Here, a synergetic approach combining theory and experiment has been employed to investigate this strategy. The framework of the density functional theory connected with the reaction field method has been applied to predict the formal potential of 137 molecules and identify promising candidates for the referent application. The effects of including different ring types, e.g. fused rings or bonded rings, heteroatoms, and pi bonds, as well as carboxyl groups on the formal potential, have been rationalized. Finally, we have identified a number of molecules with acceptable theoretical capacities that show redox matching with thiophene-based conducting polymers which, hence, are suggested as pendent groups for the development of conducting redox polymer based electrode materials.
|
|
9. |
|
|
10. |
- Bernal, Ximena E., et al.
(author)
-
Empowering Latina scientists
- 2019
-
In: Science. - : American Association for the Advancement of Science (AAAS). - 0036-8075 .- 1095-9203. ; 363:6429, s. 825-826
-
Journal article (other academic/artistic)
|
|
11. |
- Kehoe, Laura, et al.
(author)
-
Make EU trade with Brazil sustainable
- 2019
-
In: Science. - : American Association for the Advancement of Science (AAAS). - 0036-8075 .- 1095-9203. ; 364:6438, s. 341-
-
Journal article (other academic/artistic)
|
|
12. |
- Muscarella, Robert, et al.
(author)
-
The global abundance of tree palms
- 2020
-
In: Global Ecology and Biogeography. - : Wiley. - 1466-822X .- 1466-8238. ; 29:9, s. 1495-1514
-
Journal article (peer-reviewed)abstract
- AimPalms are an iconic, diverse and often abundant component of tropical ecosystems that provide many ecosystem services. Being monocots, tree palms are evolutionarily, morphologically and physiologically distinct from other trees, and these differences have important consequences for ecosystem services (e.g., carbon sequestration and storage) and in terms of responses to climate change. We quantified global patterns of tree palm relative abundance to help improve understanding of tropical forests and reduce uncertainty about these ecosystems under climate change.LocationTropical and subtropical moist forests.Time periodCurrent.Major taxa studiedPalms (Arecaceae).MethodsWe assembled a pantropical dataset of 2,548 forest plots (covering 1,191 ha) and quantified tree palm (i.e., ≥10 cm diameter at breast height) abundance relative to co‐occurring non‐palm trees. We compared the relative abundance of tree palms across biogeographical realms and tested for associations with palaeoclimate stability, current climate, edaphic conditions and metrics of forest structure.ResultsOn average, the relative abundance of tree palms was more than five times larger between Neotropical locations and other biogeographical realms. Tree palms were absent in most locations outside the Neotropics but present in >80% of Neotropical locations. The relative abundance of tree palms was more strongly associated with local conditions (e.g., higher mean annual precipitation, lower soil fertility, shallower water table and lower plot mean wood density) than metrics of long‐term climate stability. Life‐form diversity also influenced the patterns; palm assemblages outside the Neotropics comprise many non‐tree (e.g., climbing) palms. Finally, we show that tree palms can influence estimates of above‐ground biomass, but the magnitude and direction of the effect require additional work.ConclusionsTree palms are not only quintessentially tropical, but they are also overwhelmingly Neotropical. Future work to understand the contributions of tree palms to biomass estimates and carbon cycling will be particularly crucial in Neotropical forests.
|
|
13. |
- Ademuyiwa, Adesoji O., et al.
(author)
-
Determinants of morbidity and mortality following emergency abdominal surgery in children in low-income and middle-income countries
- 2016
-
In: BMJ Global Health. - : BMJ Publishing Group Ltd. - 2059-7908. ; 1:4
-
Journal article (peer-reviewed)abstract
- Background: Child health is a key priority on the global health agenda, yet the provision of essential and emergency surgery in children is patchy in resource-poor regions. This study was aimed to determine the mortality risk for emergency abdominal paediatric surgery in low-income countries globally.Methods: Multicentre, international, prospective, cohort study. Self-selected surgical units performing emergency abdominal surgery submitted prespecified data for consecutive children aged <16 years during a 2-week period between July and December 2014. The United Nation's Human Development Index (HDI) was used to stratify countries. The main outcome measure was 30-day postoperative mortality, analysed by multilevel logistic regression.Results: This study included 1409 patients from 253 centres in 43 countries; 282 children were under 2 years of age. Among them, 265 (18.8%) were from low-HDI, 450 (31.9%) from middle-HDI and 694 (49.3%) from high-HDI countries. The most common operations performed were appendectomy, small bowel resection, pyloromyotomy and correction of intussusception. After adjustment for patient and hospital risk factors, child mortality at 30 days was significantly higher in low-HDI (adjusted OR 7.14 (95% CI 2.52 to 20.23), p<0.001) and middle-HDI (4.42 (1.44 to 13.56), p=0.009) countries compared with high-HDI countries, translating to 40 excess deaths per 1000 procedures performed.Conclusions: Adjusted mortality in children following emergency abdominal surgery may be as high as 7 times greater in low-HDI and middle-HDI countries compared with high-HDI countries. Effective provision of emergency essential surgery should be a key priority for global child health agendas.
|
|
14. |
- Almeida, Rafael M., et al.
(author)
-
High Primary Production Contrasts with Intense Carbon Emission in a Eutrophic Tropical Reservoir
- 2016
-
In: Frontiers in Microbiology. - : Frontiers Media SA. - 1664-302X. ; 7
-
Journal article (peer-reviewed)abstract
- Recent studies from temperate lakes indicate that eutrophic systems tend to emit less carbon dioxide (Co-2) and bury more organic carbon (OC) than oligotrophic ones, rendering them CO2 sinks in some cases. However, the scarcity of data from tropical systems is critical for a complete understanding of the interplay between eutrophication and aquatic carbon (C) fluxes in warm waters. We test the hypothesis that a warm eutrophic system is a source of both CO2 and CH4 to the atmosphere, and that atmospheric emissions are larger than the burial of OC in sediments. This hypothesis was based on the following assumptions: (i) OC mineralization rates are high in warm water systems, so that water column CO2 production overrides the high C uptake by primary producers, and (ii) increasing trophic status creates favorable conditions for CH4 production. We measured water-air and sediment-water CO2 fluxes, CH4 diffusion, ebullition and oxidation, net ecosystem production (NEP) and sediment OC burial during the dry season in a eutrophic reservoir in the semiarid northeastern Brazil. The reservoir was stratified during daytime and mixed during nighttime. In spite of the high rates of primary production (4858 +/- 934 mg C m(-2) d(-1)), net heterotrophy was prevalent due to high ecosystem respiration (5209 +/- 992 mg C m(-2) d(-1)). Consequently, the reservoir was a source of atmospheric CO2 (518 +/- 182 mg C m(-2) d(-1)). In addition, the reservoir was a source of ebullitive (17 +/- 10 mg C m(-2) d(-1)) and diffusive CH4 (11 +/- 6 mg C m(-2) d(-1)). OC sedimentation was high (1162 mg C m(-2) d(-1)), but our results suggest that the majority of it is mineralized to CO2 (722 +/- 182 mg C m(-2) d(-1)) rather than buried as OC (440 mg C m(-2) d(-1)). Although temporally resolved data would render our findings more conclusive, our results suggest that despite being a primary production and OC burial hotspot, the tropical eutrophic system studied here was a stronger CO2 and CH4 source than a C sink, mainly because of high rates of OC mineralization in the water column and sediments.
|
|
15. |
- Araujo, Rafael B., et al.
(author)
-
Evaluating bulk Nb2O2F3 for Li-battery electrode applications
- 2016
-
In: Physical Chemistry, Chemical Physics - PCCP. - : Royal Society of Chemistry (RSC). - 1463-9076 .- 1463-9084. ; 18:5, s. 3530-3535
-
Journal article (peer-reviewed)abstract
- This investigation has the primary objective of elucidating the lithium intercalation process in the crystal structure of a new niobium oxyfluoride compound Nb2O2F3. The framework of the density functional theory was applied in a generalized gradient approximation together with the hybrid functional method. It is revealed that lithium atoms intercalate in this material in a maximum concentration of one Li atom per formula unit forming LiNb2O2F3. Moreover, octahedral positions in between the layers of Nb-O-F appear as the Li preferred occupancy resulting in a structural volume expansion of only 5%. Electronic structure evolution with the insertion of lithium displays a transformation from semi-conductor to metal when half of the lithium atoms are added. This transformation occurs due to a symmetry break induced by the transition from the + 8 to + 7 oxidation state of half of the Nb2 dimers. Then, after full lithiation the symmetry is recovered and the material becomes a semiconductor again with a band gap amounting to 1 eV. The evaluated average deintercalation potential reaches 1.29 V vs. Li/Li+ with activation energy for lithium ion migration of 0.79 eV. The computed low potential of the redox reaction Nb-2(8+) to Nb-2(7+) includes niobium oxyfluoride in the map of possible materials for the anode application of Li-ion batteries.
|
|
16. |
- Araujo, Rafael B., et al.
(author)
-
First-principles investigation of Li ion diffusion in Li2FeSiO4
- 2013
-
In: Solid State Ionics. - : Elsevier BV. - 0167-2738 .- 1872-7689. ; 247, s. 8-14
-
Journal article (peer-reviewed)abstract
- We have studied the Li-ion migration and the electrochemical performance of Li2FeSiO4 in the monoclinic crystal structure with P2(1) symmetry and the related delithiated system LiFeSiO4. For this purpose, the framework of the density functional theory within the generalized gradient approximation in conjunction with the climbing image nudged elastic band method was used. Addition of the Hubbard term was also considered in the Kohn-Sham Hamiltonian to better model the d electrons of the metal ions in this material. The calculated activation energies for Li ion migration are found to decrease by around 20% with the Hubbard term inclusion in the chosen diffusion pathways of Li2FeSiO4. Regarding the delithiated structure, the activation energies were found to be sensitive to the Hubbard term addition, however no general behavior such as in the lithiated structure was found. Furthermore, the diffusion coefficients were calculated considering temperatures of 300 K, 500 K, and 700 K.
|
|
17. |
- Araujo, Rafael B., et al.
(author)
-
High-entropy alloy catalysts : Fundamental aspects, promises towards electrochemical NH3 production, and lessons to learn from deep neural networks
- 2023
-
In: Nano Energy. - : Elsevier. - 2211-2855 .- 2211-3282. ; 105
-
Journal article (peer-reviewed)abstract
- A computational approach to judiciously predict high-entropy alloys (HEAs) as an efficient and sustainable material class for the electrochemical reduction of nitrogen is here presented. The approach employs density functional theory (DFT), adsorption energies of N atoms and N2 molecules as descriptors of the catalytic activity and deep neural networks. A probabilistic approach to quantifying the activity of HEA catalysts for nitrogen reduction reaction (NRR) is described, where catalyst elements and concentration are optimized to increase the probability of specific atomic arrangements on the surfaces. The approach provides key features for the effective filtering of HEA candidates without the need for time-consuming calculations. The relationships between activity and selectivity, which correlate with the averaged valence electron concentration and averaged electronegativity of the reference HEA catalyst, are analyzed in terms of sufficient interaction for sustained reactions and, at the same time, for the release of the active site. As a result, a complete list of 3000 HEAs consisting of quinary components of the elements Mo, Cr, Mn, Fe, Co, Ni, Cu, and Zn are reported together with their metrics to rank them from the most likely to the least likely active catalysts for NRR in gas diffusion electrodes, or for the case where non-aqueous electrolytes are utilized to suppress the competing hydrogen evolution reaction. Moreover, the energetic landscape of the electrochemical NRR transformations are computed and compared to the case of Fe. The study also analyses and discusses how the results would translate to liquid-solid reactions in aqueous electrochemical cells, further affected by changes in properties upon hydroxylation, oxygen, hydrogen, and water coverages.
|
|
18. |
- Araujo, Rafael B., et al.
(author)
-
Insights in the electronic structure and redox reaction energy in LiFePO4 battery material from an accurate Tran-Blaha modified Becke Johnson potential
- 2015
-
In: Journal of Applied Physics. - : American Institute of Physics (AIP). - 0021-8979 .- 1089-7550. ; 118:12
-
Journal article (peer-reviewed)abstract
- The main goals of this paper are to investigate the accuracy of the Tran-Blaha modified Becke Johnson (TB-mBJ) potential to predict the electronic structure of lithium iron phosphate and the related redox reaction energy with the lithium deintercalation process. The computed electronic structures show that the TB-mBJ method is able to partially localize Fe-3d electrons in LiFePO4 and FePO4 which usually is a problem for the generalized gradient approximation (GGA) due to the self interaction error. The energy band gap is also improved by the TB-mBJ calculations in comparison with the GGA results. It turned out, however, that the redox reaction energy evaluated by the TB-mBJ technique is not in good agreement with the measured one. It is speculated that this disagreement in the computed redox energy and the experimental value is due to the lack of a formal expression to evaluate the exchange and correlation energy. Therefore, the TB-mBJ is an efficient method to improve the prediction of the electronic structures coming form the standard GGA functional in LiFePO4 and FePO4. However, it does not appear to have the same efficiency for evaluating the redox reaction energies for the investigated system.
|
|
19. |
- Araujo, Rafael B., et al.
(author)
-
Lithium transport investigation in LixFeSiO4 : A promising cathode material
- 2013
-
In: Solid State Communications. - : Elsevier BV. - 0038-1098 .- 1879-2766. ; 173, s. 9-13
-
Journal article (peer-reviewed)abstract
- In this paper we investigate lithium mobility in both Li 2FeSiO4 and its half-lithiated state LiFeSiO4 considering an orthorhombic crystal structure. We find that the calculated activation energy of Li+ ions hopping between adjacent equilibrium sites predicts two least hindered diffusion pathways in both materials. One of them is along the [100] direction characterizing an ionic diffusion in a straight line and the other follows a zig-zag way between the Fe-Si-O layers. We also show that diffusion of Li+ ions in the half-lithiated structure follows the same behavior as in the lithiated structure. As a whole, the activation energies for the investigated compounds present a greater value compared with the activation energies in currently used materials such as LiFePO4. The results were calculated in the framework of density functional theory in conjunction with the climbing image nudged elastic band method. The Hubbard term was added to the Kohn-Sham Hamiltonian to overcome the delocalization problem of d electrons. Furthermore, the diffusion coefficients were calculated for both structures considering temperatures ranging from 300 to 700 K.
|
|
20. |
- Araujo, Rafael Barros Neves de, et al.
(author)
-
Divulging the Hidden Capacity and Sodiation Kinetics of NaxC6Cl4O2 : A High Voltage Organic Cathode for Sodium Rechargeable Batteries
- 2017
-
In: The Journal of Physical Chemistry C. - : American Chemical Society (ACS). - 1932-7447 .- 1932-7455. ; 121:26, s. 14027-14036
-
Journal article (peer-reviewed)abstract
- In the current emerging sustainable organic battery field, quinones are seen as one of the prime candidates for application in rechargeable battery electrodes. Recently, C6Cl4O2, a modified quinone, has been proposed as a high voltage organic cathode. However, the sodium insertion mechanism behind the cell reaction remained unclear due to the nescience of the right crystal structure. Here, the framework of the density functional theory (DFT) together with an evolutionary algorithm was employed to elucidate the crystal structures of the compounds NaxC6Cl4O2 (x = 0.5, 1.0, 1.5 and 2). Along with the usefulness of PBE functional to reflect the experimental potential, also the importance of the hybrid functional to divulge the hidden theoretical capacity is evaluated. We showed that the experimentally observed lower specific capacity is a result of the great stabilization of the intermediate phase Na1.5C6Cl4O2. The calculated activation barriers for the ionic hops are 0.68, 0.40, and 0.31 eV, respectively, for NaC6Cl4O2, Na1.5C6Cl4O2, and Na2C6Cl4O2. These results indicate that the kinetic process must not be a limiting factor upon Na insertion. Finally, the correct prediction of the specific capacity has confirmed that the theoretical strategy used, employing evolutionary simulations together with the hybrid functional framework, can rightly model the thermodynamic process in organic electrode compounds.
|
|
21. |
- Araújo, Rafael Barros Neves de
(author)
-
Energy Storage Materials: Insights From ab Initio Theory : Diffusion, Structure, Thermodynamics and Design.
- 2017
-
Doctoral thesis (other academic/artistic)abstract
- The development of science and technology have provided a lifestyle completely dependent on energy consumption. Devices such as computers and mobile phones are good examples of how our daily life depends on electric energy. In this scenario, energy storage technologies emerge with strategic importance providing efficient ways to transport and commercialize the produced energy. Rechargeable batteries come as the most suitable alternative to fulfill the market demand due to their higher energy- and power- density when compared with other electrochemical energy storage systems. In this context, during the production of this thesis, promising compounds for advanced batteries application were investigated from the theoretical viewpoint. The framework of the density functional theory has been employed together with others theoretical tools to study properties such as ionic diffusion, redox potential, electronic structure and crystal structure prediction.Different organic materials were theoretically characterized with quite distinct objectives. For instance, a protocol able to predict the redox potential in solution of long oligomers were developed and tested against experimental measurements. Strategies such as anchoring of small active molecules on polymers backbone have also been investigated through a screening process that determined the most promising candidates. Methods such as evolutionary simulation and basin-hopping algorithm were employed to search for global minimum crystal structures of small molecules and inorganic compounds working as a cathode of advanced sodium batteries. The crystal structure evolution of C6Cl4O2 upon Na insertion was unveiled and the main reasons behind the lower specific capacity obtained in the experiment were clarified. Ab initio molecular dynamics and the nudged elastic band method were employed to understand the underlying ionic diffusion mechanisms in the recently proposed Alluaudite and Eldfellite cathode materials. Moreover, it was demonstrated that electronic conduction in Na2O2, a byproduct of the Na-O2 battery, occurs via hole polarons hopping. Important physical and chemical insights were obtained during the production of this thesis. It finally supports the development of low production cost, environmental friendliness and efficient electrode compounds for advanced secondary batteries.
|
|
22. |
|
|
23. |
- Araujo, Rafael B., et al.
(author)
-
Na2M2(SO4)(3) (M = Fe, Mn, Co and Ni) : towards high-voltage sodium battery applications
- 2016
-
In: Physical Chemistry, Chemical Physics - PCCP. - : Royal Society of Chemistry (RSC). - 1463-9076 .- 1463-9084. ; 18:14, s. 9658-9665
-
Journal article (peer-reviewed)abstract
- Sodium-ion-based batteries have evolved as excellent alternatives to their lithium-ion-based counterparts due to the abundance, uniform geographical distribution and low price of Na resources. In the pursuit of sodium chemistry, recently the alluaudite framework Na2M2(SO4)(3) has been unveiled as a high-voltage sodium insertion system. In this context, the framework of density functional theory has been applied to systematically investigate the crystal structure evolution, density of states and charge transfer with sodium ions insertion, and the corresponding average redox potential, for Na2M2(SO4)(3) (M = Fe, Mn, Co and Ni). It is shown that full removal of sodium atoms from the Fe-based device is not a favorable process due to the 8% volume shrinkage. The imaginary frequencies obtained in the phonon dispersion also reflect this instability and the possible phase transition. This high volume change has not been observed in the cases of the Co- and Ni-based compounds. This is because the redox reaction assumes a different mechanism for each of the compounds investigated. For the polyanion with Fe, the removal of sodium ions induces a charge reorganization at the Fe centers. For the Mn case, the redox process induces a charge reorganization of the Mn centers with a small participation of the oxygen atoms. The Co and Ni compounds present a distinct trend with the redox reaction occurring with a strong participation of the oxygen sublattice, resulting in a very small volume change upon desodiation. Moreover, the average deintercalation potential for each of the compounds has been computed. The implications of our findings have been discussed both from the scientific perspective and in terms of technological aspects.
|
|
24. |
- Araujo, Rafael B., et al.
(author)
-
Predicting electrochemical properties and ionic diffusion in Na2+2xMn2-x(SO4)(3) : crafting a promising high voltage cathode material
- 2016
-
In: Journal of Materials Chemistry A. - : Royal Society of Chemistry. - 2050-7488 .- 2050-7496. ; 4:2, s. 451-457
-
Journal article (peer-reviewed)abstract
- Sodium ion batteries have emerged as a good alternative to lithium based systems due to their low cost of production. In this scenario, the search for higher voltage, sodium cathodes results in a new promising alluaudite structure Na2+2xMn2-x(SO4)(3). The structural, electronic and Na diffusion properties along with defects have been reported in this investigation within the framework of density functional theory. A band gap of 3.61 eV has been computed and the average deintercalation potential is determined to be 4.11 V vs. Na/Na+. A low concentration of anti-site defects is predicted due to their high formation energy. The biggest issue for the ionic diffusion in the Na2+2xMn2-x(SO4)(3) crystal structure is revealed to be the effect of Mn vacancies increasing the activation energy of Na+ ions that hop along the [001] equilibrium positions. This effect leads to activation energies of almost the same high values for the ionic hop through the [010] direction characterizing a 2D like ionic diffusion mechanism in this system.
|
|
25. |
- Araujo, Rafael B., et al.
(author)
-
Unveiling the charge migration mechanism in Na2O2 : implications for sodium-air batteries
- 2015
-
In: Physical Chemistry, Chemical Physics - PCCP. - : Royal Society of Chemistry (RSC). - 1463-9076 .- 1463-9084. ; 17:12, s. 8203-8209
-
Journal article (peer-reviewed)abstract
- Metal-air batteries have become promising candidates for modern energy storage due to their high theoretical energy density in comparison to other storage devices. The lower overpotential of Na compared with Li makes Na-air batteries more efficient in terms of battery lifetime. Additionally, the abundance of Na over Li is another advantage for Na batteries compared to Li batteries. Na2O2 is one of the main products of sodium-air battery reactions. The efficiency of air cells is always related to the charge transport mechanisms in the formed product. To unveil these diffusion mechanisms in one of the main products of the cell reaction Na-O-2 we systematically investigate the mobility of charge carriers as well as the electronic structural properties of sodium peroxide. The framework of the density functional theory based on hybrid functional approach is used to study the mobility of charge carriers and intrinsic defects in Na2O2. Our calculations reveal that the formation of small electron and hole polarons is preferentially occurring over the delocalized state in the crystal structure of Na2O2. The migration of these small polarons displays activation energies of about 0.92 eV and 0.32 eV for the electron and hole polarons respectively, while the analysis of the charged sodium vacancy mobility reveals an activation energy of about 0.5 eV. These results suggest that the charge transport in sodium peroxide would mainly occur through the diffusion of hole polarons.
|
|