1. |
- Lopes, T. S., et al.
(author)
-
Cu(In,Ga)Se2 based ultrathin solar cells the pathway from lab rigid to large scale flexible technology
- 2023
-
In: npj Flexible Electronics. - : Springer Nature. - 2397-4621. ; 7:1
-
Journal article (peer-reviewed)abstract
- The incorporation of interface passivation structures in ultrathin Cu(In,Ga)Se2 based solar cells is shown. The fabrication used an industry scalable lithography technique—nanoimprint lithography (NIL)—for a 15 × 15 cm2 dielectric layer patterning. Devices with a NIL nanopatterned dielectric layer are benchmarked against electron-beam lithography (EBL) patterning, using rigid substrates. The NIL patterned device shows similar performance to the EBL patterned device.The impact of the lithographic processes in the rigid solar cells’ performance were evaluated via X-ray Photoelectron Spectroscopy and through a Solar Cell Capacitance Simulator. The device on stainless-steel showed a slightly lower performance than the rigid approach, due to additional challenges of processing steel substrates, even though scanning transmission electron microscopy did not show clear evidence of impurity diffusion. Notwithstanding, time-resolved photoluminescence results strongly suggested elemental diffusion from the flexible substrate. Nevertheless, bending tests on the stainless-steel device demonstrated the mechanical stability of the CIGS-based device.
|
|
2. |
- Bose, Sourav, et al.
(author)
-
A morphological and electronic study of ultrathin rear passivated Cu(In,Ga)Se2 solar cells
- 2019
-
In: Thin Solid Films. - : Elsevier BV. - 0040-6090 .- 1879-2731. ; 671, s. 77-84
-
Journal article (peer-reviewed)abstract
- The effects of introducing a passivation layer at the rear of ultrathin Copper Indium Gallium di-Selenide Cu(In,Ga)Se2 (CIGS) solar cells is studied. Point contact structures have been created on 25 nm Al2O3 layer using e-beam lithography. Reference solar cells with ultrathin CIGS layers provide devices with average values of light to power conversion efficiency of 8.1% while for passivated cells values reached 9.5%. Electronic properties of passivated cells have been studied before, but the influence of growing the CIGS on Al2O3 with point contacts was still unknown from a structural and morphological point of view. Scanning Electron Microscopy, X-ray Diffraction and Raman spectroscopy measurements were performed. These measurements revealed no significant morphological or structural differences in the CIGS layer for the passivated samples compared with reference samples. These results are in agreement with the similar values of carrier density (~8 x 1016 cm-3) and depletion region (~160 nm) extracted using electrical measurements. A detailed comparison between both sample types in terms of current-voltage, external quantum efficiency and photoluminescence measurements show very different optoelectronic behaviour which is indicative of a successful passivation. SCAPS simulations are done to explain the observed results in view of passivation of the rear interface.
|
|
3. |
- Salome, Pedro M. P., et al.
(author)
-
Passivation of Interfaces in Thin Film Solar Cells : Understanding the Effects of a Nanostructured Rear Point Contact Layer
- 2018
-
In: Advanced Materials Interfaces. - : Wiley. - 2196-7350. ; 5:2
-
Journal article (peer-reviewed)abstract
- Thin film solar cells based in Cu(In,Ga)Se-2 (CIGS) are among the most efficient polycrystalline solar cells, surpassing CdTe and even polycrystalline silicon solar cells. For further developments, the CIGS technology has to start incorporating different solar cell architectures and strategies that allow for very low interface recombination. In this work, ultrathin 350 nm CIGS solar cells with a rear interface passivation strategy are studied and characterized. The rear passivation is achieved using an Al2O3 nanopatterned point structure. Using the cell results, photoluminescence measurements, and detailed optical simulations based on the experimental results, it is shown that by including the nanopatterned point contact structure, the interface defect concentration lowers, which ultimately leads to an increase of solar cell electrical performance mostly by increase of the open circuit voltage. Gains to the short circuit current are distributed between an increased rear optical reflection and also due to electrical effects. The approach of mixing several techniques allows us to make a discussion considering the different passivation gains, which has not been done in detail in previous works. A solar cell with a nanopatterned rear contact and a 350 nm thick CIGS absorber provides an average power conversion efficiency close to 10%.
|
|