1. |
- Abel, I, et al.
(author)
-
Overview of the JET results with the ITER-like wall
- 2013
-
In: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10, s. 104002-
-
Journal article (peer-reviewed)abstract
- Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Z(eff) (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. The re-establishment of the baseline H-mode and hybrid scenarios compatible with the new wall has required an optimization of the control of metallic impurity sources and heat loads. Stable type-I ELMy H-mode regimes with H-98,H-y2 close to 1 and beta(N) similar to 1.6 have been achieved using gas injection. ELM frequency is a key factor for the control of the metallic impurity accumulation. Pedestal temperatures tend to be lower with the new wall, leading to reduced confinement, but nitrogen seeding restores high pedestal temperatures and confinement. Compared with the carbon wall, major disruptions with the new wall show a lower radiated power and a slower current quench. The higher heat loads on Be wall plasma-facing components due to lower radiation made the routine use of massive gas injection for disruption mitigation essential.
|
|
2. |
- Brunsell, Per R., et al.
(author)
-
Mode Dynamics and Confinement in the Reversed-field Pinch
- 2000
-
In: 18<sup>th</sup> IAEA Fusion Energy Conference in Sorrento, Italy, 4-10 Oct. 2000. Paper IAEA-CN-77/EXP3/14.
-
Conference paper (peer-reviewed)abstract
- Tearing mode dynamics and toroidal plasma flow in the RFP has been experimentally studied in the Extrap T2 device. A toroidally localised, stationary magnetic field perturbation, the ``slinky mode'' is formed in nearly all discharges. There is a tendency of increased phase alignment of different toroidal Fourier modes, resulting in higher localised mode amplitudes, with higher magnetic fluctuation level. The fluctuation level increases slightly with increasing plasma current and plasma density. The toroidal plasma flow velocity and the ion temperature has been measured with Doppler spectroscopy. Both the toroidal plasma velocity and the ion temperature clearly increase with I/N. Initial, preliminary experimental results obtained very recently after a complete change of the Extrap T2 front-end system (first wall, shell, TF coil), show that an operational window with mode rotation most likely exists in the rebuilt device, in contrast to the earlier case discussed above. A numerical code DEBSP has been developed to simulate the behaviour of RFP confinement in realistic geometry, including essential transport physics. Resulting scaling laws are presented and compared with results from Extrap T2 and other RFP experiments.
|
|
3. |
|
|
4. |
- Cecconello, Marco, et al.
(author)
-
Total radiation losses studies in EXTRAP T2R
- 2001
-
In: Proceedings of the 28th European Physical Society Conference on Controlled Fusion and Plasma Physics. - Madeira.
-
Conference paper (other academic/artistic)
|
|
5. |
|
|
6. |
- de Vries, P. C., et al.
(author)
-
Effect of toroidal field ripple on the formation of internal transport barriers
- 2008
-
In: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 0741-3335 .- 1361-6587. ; 50:6
-
Journal article (peer-reviewed)abstract
- The effect of a toroidal field (TF) ripple on the formation and performance of internal transport barriers (ITBs) has been studied in JET. It was found that the TF ripple had a profound effect on the toroidal plasma rotation. An increased TF ripple up to delta = 1% led to a lower rotation and reduced the rotational shear in the region where the ITBs were formed. ITB triggering events were observed in all cases and it is thought that the rotational shear may be less important for this process than, for example, the q-profile. However, the increase in the pressure gradient following the ITB trigger was reduced in discharges with a larger TF ripple and consequently a lower rotational shear. This suggests that toroidal rotation and its shear play a role in the growth of the ITB once it has been triggered.
|
|
7. |
- Eriksson, L-G, et al.
(author)
-
Plasma rotation induced by directed waves in the ion-cyclotron range of frequencies
- 2004
-
In: Physical Review Letters. - 0031-9007 .- 1079-7114. ; 92:23
-
Journal article (peer-reviewed)abstract
- Changes of the toroidal plasma rotation induced by directed waves in the ion-cyclotron range of frequencies (ICRF) have been identified experimentally for the first time on the JET tokamak. The momentum carried by the waves is initially absorbed by fast resonating ions, which subsequently transfer it to the bulk plasma. Thus, the results provide evidence for the influence of ICRF heated fast ions on plasma rotation.
|
|
8. |
|
|
9. |
- Eriksson, L. -G, et al.
(author)
-
Toroidal rotation in RF heated JET plasmas
- 2007
-
In: RADIO FREQUENCY POWER IN PLASMAS. - : AIP. - 9780735404441 ; , s. 59-62
-
Conference paper (peer-reviewed)abstract
- Experiments have been carried out on JET aimed at studying rotation in RF heated plasmas with low external momentum input. Both plasmas with Ion Cyclotron Resonance Frequency (ICRF) heating and Lower Hybrid Current Drive (LHCD) have been investigated. The rotation profiles are measured by Charge Exchange recombination spectroscopy, using short diagnostic Neutral Beam Injection (NBI) pulses. Moreover, the temporal evolution of the central rotation could in some cases be deduced from MHD activity. While most of the measurements were focussed on ICRF heating, the profiles measured in plasmas with LHCD are interesting since they are the first reported from JET in such plasmas. In particular, they allowed for studies of rotation in RF heated plasmas with q>1. The experimental results are presented together with an analysis of the torque from ICRF heated fast ions.
|
|
10. |
- Eriksson, L. G., et al.
(author)
-
Toroidal rotation in RF heated JET plasmas
- 2009
-
In: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 0741-3335 .- 1361-6587. ; 51:4
-
Journal article (peer-reviewed)abstract
- Observations of bulk plasma rotation in radio frequency (RF) heated JET discharges are reported. This study is concentrated on RF heated L-mode plasmas. In particular, the toroidal rotation profiles in plasmas heated by ion cyclotron resonance frequency (ICRF) waves and lower hybrid (LH) waves have been analysed. It is the first time that rotation profiles in JET plasmas with LH waves have been measured in dedicated discharges. It is found that the toroidal plasma rotation in the outer region of the plasmas is in the co-current direction irrespective of the heating scenario. An interesting feature is that the toroidal rotation profile appears to be hollow in many discharges at low plasma current, but a low current in itself does not seem to be a sufficient condition for finding such profiles. Fast ion transport and finite orbit width effects are mechanisms that could explain hollow rotation profiles. This possibility has been investigated by numerical simulations of the torque on the bulk plasma due to fast ICRF accelerated ions. The obtained torque is used in a transport equation for the toroidal momentum density to estimate the effect on the thermal bulk plasma rotation profile.
|
|
11. |
- Hawkes, N. C., et al.
(author)
-
Ion transport barrier formation with low injected torque in JET
- 2007
-
In: 34th EPS Conference on Plasma Physics 2007, EPS 2007 - Europhysics Conference Abstracts. - 9781622763344 ; , s. 504-507
-
Conference paper (peer-reviewed)abstract
- Ion temperature ITB trigger events have been provoked on JET with very low levels of injected torque using a 3He minority ion heating scheme. The evidence indicates that E x B shear driven by toroidal rotation is not important in these ITB triggers, however the ITBs which form are weak and short lived. Evidence from other experiments [4], suggests that higher torque is necessary to establish and maintain strong ITBs. Future experiments with the increased RF power of the new JET ICRH antenna will be made to explore whether 'strong' ITBs can be created at high power and low applied torque.
|
|
12. |
|
|
13. |
- Lamalle, P. U., et al.
(author)
-
Expanding the operating space of ICRF on JET with a view to ITER
- 2006
-
In: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 46:2, s. 391-400
-
Journal article (peer-reviewed)abstract
- This paper reports on ITER-relevant ion cyclotron resonance frequency (ICRF) physics investigated on JET in 2003 and early 2004. Minority heating of helium three in hydrogen plasmas-(He-3)H-was systematically explored by varying the 3 He concentration and the toroidal phasing of the antenna arrays. The best heating performance (a maximum electron temperature of 6.2 keV with 5 MW of ICRF power) was obtained with a preferential wave launch in the direction of the plasma current. A clear experimental demonstration was made of the sharp and reproducible transition to the mode conversion heating regime when the 3 He concentration increased above similar to 2%. In the latter regime the best heating performance (a maximum electron temperature of 8 keV with 5 MW of ICRF power) was achieved with dipole array phasing, i.e. a symmetric antenna power spectrum. Minority heating of deuterium in hydrogen plasmas-(D)H-was also investigated but was found inaccessible because this scenario is too sensitive to impurity ions with Z/A = 1/2 such as C6+, small amounts of which directly lead into the mode conversion regime. Minority heating of up to 3% of tritium in deuterium plasmas was systematically investigated during the JET trace tritium experimental campaign (TTE). This required operating JET at its highest possible magnetic field (3.9 to 4 T) and the ICRF system at its lowest frequency (23 MHz). The interest of this scenario for ICRF heating at these low concentrations and its efficiency at boosting the suprathermal neutron yield were confirmed, and the measured neutron and gammay ray spectra permit interesting comparisons with advanced ICRF code simulations. Investigations of finite Larmor radius effects on the RF-induced high-energy tails during second harmonic (omega = 2 omega(c)) heating of a hydrogen minority in D plasmas clearly demonstrated a strong decrease in the RF diffusion coefficient at proton energies similar to 1 MeV in agreement with theoretical expectations. Fast wave heating and current drive experiments in deuterium plasmas showed effective direct electron heating with dipole phasing of the antennas, but only small changes of the central plasma current density were observed with the directive phasings, in particular at low single pass damping. New investigations of the heating efficiency of ICRF antennas confirmed its strong dependence on the parallel wavenumber spectrum. Advances in topics of a more technological nature are also summarized: ELM studies using fast RF measurements, the successful experimental demonstration of a new ELM-tolerant antenna matching scheme and technical enhancements planned on the JET ICRF system for 2006, they being equally strongly driven by the preparation for ITER.
|
|
14. |
- Lawson, K. D., et al.
(author)
-
Enhancements to the JET poloidally scanning vacuum ultravioletvisible spectrometers
- 2012
-
In: Review of Scientific Instruments. - : AIP Publishing. - 0034-6748 .- 1089-7623. ; 83:10, s. 10D536-
-
Journal article (peer-reviewed)abstract
- Enhancements to the JET poloidally scanning spectrometers are presented, which will aid the exploitation of the recently installed ITER-like wall in JET. They include the installation of visible filterphotomultiplier tube assemblies and spectrometers and the replacement of large rotating mirrors in the JET vacuum with small oscillating mirrors outside. The upgrade has resulted in a more robust and reliable diagnostic than before, which is described. Drifts in the mirror angle reconstructed from quadrature encoder signals are found, a reference signal being required. The use of the small scanning mirrors necessitated the inclusion of focusing mirrors to maintain throughput into the vacuum ultraviolet spectrometers. The mirror design has taken account of the extreme sensitivity of the focusing to the grazing angle of incidence, an aspect of importance in the design of grazing incidence focusing components on future machines, such as ITER. The visible system has been absolutely calibrated using an in-vessel light source.
|
|
15. |
- Loarer, T., et al.
(author)
-
Fuel retention in L and H mode experiments in JET
- 2007
-
In: 34th EPS Conference on Plasma Physics 2007, EPS 2007 - Europhysics Conference Abstracts. - 9781622763344 ; , s. 13-16
-
Conference paper (peer-reviewed)abstract
- The fuel retention has been studied out in JET in L mode, Type III and Type I ELMy H-modes using gas balance in series of repetitive pulses with an overall accuracy of about 1.2%. The short term (dynamic) retention is important for both L mode and Type III ELMy H-mode over the heating phases (respectively 13 and 17 sec) but decreases already significantly during the pulse. It becomes small already after 6 sec for the Type I ELMy H-mode conditions. In all the cases, the recovery after the pulse contributes for a weak part in the gas balance and in the overall fuel retention. The absolute long term fuel retention (on the time basis of typically 5 hours) for the different plasma conditions is between 1.3 and 2.8 1021Ds-1 (averaged over the plasma heating time) and in reasonable agreement with the value deduced from post mortem tile analysis of about 5 1020Ds-1 considering the additional long term outgassing, conditioning and disruptions included in the post mortem analysis. The increase of the long term retention observed from L mode to Type I ELMy H-mode is associated to the increase of the recycling flux and the ELM energy. This larger long term retention is attributed to an enhanced carbon erosion and transport in the SOL leading to stronger carbon deposition and fuel codeposition. The results confirm the strong concerns about fuel retention in a carbon clad tokamak and a possible full carbon wall ITER which could reach the T-inventory limit in only a small number of high performance shots. A reasonable ITER operation time depends thus on a significant reduced T codeposition under the different ITER material conditions (which has to be confirmed in a relevant tokamak experiment such as the JET ILW project) and an effective routine T removal technique.
|
|
16. |
- Malmberg, Jenny A., et al.
(author)
-
Mode- and plasma rotation in a resistive shell reversed-field pinch
- 2004
-
In: Physics of Plasmas. - : AIP Publishing. - 1070-664X .- 1089-7674. ; 11:2, s. 647-658
-
Journal article (peer-reviewed)abstract
- Mode rotation studies in a resistive shell reversed-field pinch, EXTRAP T2R [P. R. Brunsell , Plasma Phys. Control. Fusion 43, 1 (2001)] are presented. The phase relations and nonlinear coupling of the resonant modes are characterized and compared with that expected from modeling based on the hypothesis that mode dynamics can be described by a quasi stationary force balance including electromagnetic and viscous forces. Both m=0 and m=1 resonant modes are studied. The m=1 modes have rotation velocities corresponding to the plasma flow velocity (20-60 km/s) in the core region. The rotation velocity decreases towards the end of the discharge, although the plasma flow velocity does not decrease. A rotating phase locked m=1 structure is observed with a velocity of about 60 km/s. The m=0 modes accelerate throughout the discharges and reach velocities as high as 150-250 km/s. The observed m=0 phase locking is consistent with theory for certain conditions, but there are several conditions when the dynamics are not described. This is not unexpected because the assumption of quasi stationarity for the mode spectra is not fulfilled for many conditions. Localized m=0 perturbations are formed in correlation with highly transient discrete dynamo events. These perturbations form at the location of the m=1 phase locked structure, but rotate with a different velocity as they spread out in the toroidal direction. (C) 2004 American Institute of Physics.
|
|
17. |
- Mazon, D., et al.
(author)
-
Real-time profile control for advanced Tokamak operation
- 2008
-
In: AIP Conf. Proc.. - : AIP. - 9780735405073 ; , s. 430-433
-
Conference paper (peer-reviewed)abstract
- Simultaneous control of the plasma shape, the magnetic and kinetic plasma profiles (such as the safety factor, q(x), and gyro-normalized temperature gradient, ρTe *;(x), respectively) and the boundary flux is being investigated on JET, and has potential applications in the operation of ITER steady state advanced tokamak discharges. The control of radially distributed parameters was achieved for the first time on JET in 2004 [1-4]. The controller was based on the static plasma response only. The approach newly implemented on JET aims to use a dynamical plasma model, all the available heating and current drive (H&CD) systems, and the poloidal field (PF) system in an optimal way to achieve a set of requested magnetic and kinetic profiles. This paper describes the new model-based optimal profile controller which has been tested during the last 2007 experimental campaign. The controller aims to use the combination of heating and current drive systems - and optionally the PF system. First experimental results of current profile control obtained during the last 2007 JET campaign are presented.
|
|
18. |
- McDonald, C., et al.
(author)
-
ELMy H-modes in JET helium-4 plasmas
- 2004
-
In: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 0741-3335 .- 1361-6587. ; 46:3, s. 519-534
-
Journal article (peer-reviewed)abstract
- ELMy H-modes in helium-4 plasmas provide valuable information on ELMy H-mode physics as well as a possible early low activation operational phase for next-step tokamaks, such as ITER. With this in mind, a series of helium-4 H-mode experiments were performed on JET with pure helium-4 NBI auxiliary heating (up to 12 MW). A set of ELMy H-mode plasmas were produced, in both the Type I ELM regime and a second regime, which showed characteristics similar to the deuterium Type III regime, but with a reverse ELM frequency dependence on power. Sawteeth were also observed, and had similar behaviour to those seen in deuterium. Compared with deuterium plasmas, Type I ELMy H-mode confinement is seen to be 28 +/- 6% poorer in helium-4 plasmas and the L-H power threshold 42 +/- 10% larger. This is the opposite of the behaviour predicted by experimental isotope mass scalings from hydrogenic plasmas.Comparison with a wider hydrogenic database, enables the effects of isotopic charge and mass to be studied independently.
|
|
19. |
- Moreau, D., et al.
(author)
-
A two-time-scale dynamic-model approach for magnetic and kinetic profile control in advanced tokamak scenarios on JET
- 2008
-
In: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 48:10
-
Journal article (peer-reviewed)abstract
- Real-time simultaneous control of several radially distributed magnetic and kinetic plasma parameters is being investigated on JET, in view of developing integrated control of advanced tokamak scenarios. This paper describes the new model-based profile controller which has been implemented during the 2006-2007 experimental campaigns. The controller aims to use the combination of heating and current drive (H&CD) systems-and optionally the poloidal field (PF) system-in an optimal way to regulate the evolution of plasma parameter profiles such as the safety factor, q(x), and gyro-normalized temperature gradient,. rho*(Te)(x). In the first part of the paper, a technique for the experimental identification of a minimal dynamic plasma model is described, taking into account the physical structure and couplings of the transport equations, but making no quantitative assumptions on the transport coefficients or on their dependences. To cope with the high dimensionality of the state space and the large ratio between the time scales involved, the model identification procedure and the controller design both make use of the theory of singularly perturbed systems by means of a two-time-scale approximation. The second part of the paper provides the theoretical basis for the controller design. The profile controller is articulated around two composite feedback loops operating on the magnetic and kinetic time scales, respectively, and supplemented by a feedforward compensation of density variations. For any chosen set of target profiles, the closest self-consistent state achievable with the available actuators is uniquely defined. It is reached, with no steady state offset, through a near-optimal
|
|
20. |
- Murari, A., et al.
(author)
-
JET new diagnostic capability on the route to ITER
- 2007
-
In: Fusion engineering and design. - : Elsevier BV. - 0920-3796 .- 1873-7196. ; 82:14-maj, s. 1161-1166
-
Journal article (peer-reviewed)abstract
- The JET scientific programme is directed towards the development of ITER relevant scenarios. In support of this, significant effort has been made to develop diagnostics to better characterise the power deposition on the plasma facing components, to investigate in more detail the radiation losses particularly in the divertor region and to better detect Magneto Hydrodynamic Modes (MHD) instabilities and their effects on fast ion confinement. A new wide-angle infrared camera provides for the first time the opportunity to perform infrared thermography in the JET main chamber, even during fast events like ELMs and disruptions. A completely new bolometric system, with better spatial resolution particularly in the divertor, is now used to investigate the total radiation losses and their influence on the ELM behaviour. A new set of microwave waveguides has improved by 20 dB the signal to noise ratio of the JET X-mode reflectometers, that are now routinely used to detect MHD instabilities and in particular to localise the location of Alfven Eigenmodes. This improved diagnostic capability to monitor MHD instabilities is complemented by two new diagnostics to detect lost fast particles. Both the new scintillator probe and a poloidal array of Faraday cups have already shown clear correlations between MHD activity and ion losses at the edge.
|
|
21. |
- Murari, A., et al.
(author)
-
Measuring the radiation field and radiation hard detectors at JET : Recent developments
- 2008
-
In: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576. ; 593:3, s. 492-504
-
Journal article (peer-reviewed)abstract
- Since in ITER the radiation field will be much more demanding than that of present day devices, research programmes at JET are aimed at developing radiation hard diagnostics and related components. Initially, significant efforts are devoted to determining the radiation field of both the plasma and in the immediate environment with better accuracy. New developments in MCNP calculations and dedicated measurements provide useful information about the radiation field in the Torus Hall, even during non-operational periods. The effect of using Beryllium in the near future for JET first wall, is being assessed. New materials for activation samples are under consideration and will be tested to improve the calibration accuracy of JET neutron diagnostics. The long-term goal of this work is to obtain spectrometric information from an appropriate combination of different materials. Several studies are under way to modify the radiation field at the detectors by using LiH or pure water as neutron filters, to alleviate the problem of the background in gamma-ray measurements. A suite of radiation hard detectors for neutrons, magnetic field and charged particles are being developed. Super-heated fluid neutron detectors, used for yield and imaging, are being upgraded, in order to provide a broadband spectrometric capability. Chemical vapour deposited diamond diodes are being qualified as counters and as spectrometers. Prototypes of Hall probes made of InSb have been installed on the machine and have provided some preliminary results. Si-on-insulator detectors are under development for use in neutral particle analysers and are currently being bench-tested. Some attention is being devoted to optical components, fibres and mirrors, and to investigating radiation hard electronics using reconfigurable Field Programmable Gate Arrays.
|
|
22. |
- Murari, A., et al.
(author)
-
New diagnostic techniques and technologies at JET (invited)
- 2006
-
In: Review of Scientific Instruments. - : AIP Publishing. - 0034-6748 .- 1089-7623. ; 77:10
-
Journal article (peer-reviewed)abstract
- The European Fusion Development Agreement's mission for JET is the development of ITER scenarios exploiting the specific properties of the device. This task requires significant improvements in the measuring techniques. The most innovative diagnostic upgrades are in the fields of edge measurements, detection of fast magnetohydrodynamics modes and burning plasma diagnostics. The importance of plasma-wall interactions, and, in particular, the issue of tritium inventory promoted the development of the quartz microbalance, a detector with improved time resolution to measure material redeposition in the remote areas of the inner divertor. Measurement of Alfven cascades with unprecedented spectral resolution, reaching a toroidal n number of up to 16, was obtained using an O-mode microwave reflectometer as an interferometer. For the diagnosis of the fusion products, a new approach is being developed to measure the He ash based on double charge exchange between thermalized particles and neutrals from JET beams. There have been several upgrades of the neutron diagnostic systems, one of which, the new time of flight neutron spectrometer designed for high counting rates is described.
|
|
23. |
- Ongena, J., et al.
(author)
-
Recent progress on JET towards the ITER reference mode of operation at high density
- 2001
-
In: Plasma Physics and Controlled Fusion. - 0741-3335 .- 1361-6587. ; 43, s. A11-A30
-
Journal article (peer-reviewed)abstract
- Recent progress towards obtaining high density and high confinement in JET as required for the ITER reference scenario at Q = 10 is summarized. Plasmas with simultaneous confinement H-98(y.2) = 1 and densities up to n/n(Gw) similar to 1 are now routinely obtained. This has been possible (i) by using plasmas at high (delta similar to 0.5) and medium (delta similar to 0.3-0.4) triangularity with sufficient heating power to maintain Type I ELMs, (ii) with impurity seeded plasmas at high (delta similar to 0.5) and low (delta less than or equal to 0.2) triangularity, (iii) with an optimized pellet injection sequence, maintaining the energy confinement and raising the density, and (iv) by carefully tuning the gas puff rate leading to plasmas with peaked density profiles and good confinement at long time scales. These high performance discharges exhibit Type I ELMs, with a new and more favourable behaviour observed at high densities, requiring further studies. Techniques for a possible mitigation of these ELMs are discussed, and first promising results are obtained with impurity seeding in discharges at high triangularity. Scaling studies using the new data of this year show a strong dependence of confinement on upper triangularity, density and proximity to the Greenwald limit. Observed MHD instabilities and methods to avoid these in high density and high confinement plasmas are discussed.
|
|
24. |
- Ongena, J, et al.
(author)
-
Towards the realization on JET of an integrated H-mode scenario for ITER
- 2004
-
In: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 44:1, s. 124-133
-
Journal article (peer-reviewed)abstract
- ELMy H-mode experiments at JET in 2000/mid-2002 have focused on discharges with normalized parameters for plasma density, energy confinement and beta similar to those of the ITER Q(DT) = 10 reference regime (n/n(GW) similar to 0.85, H(98(y,2)) similar to 1, beta(N) similar to 1.8). ELMy H-mode plasmas have been realized reaching or even exceeding those parameters in steady-state conditions (up to similar to5 s or 12tau(epsilon)) in a reproducible way and only limited by the duration of the additional heating phase. These results have been obtained (a) in highly triangular plasmas, by increasing the average triangularity delta towards the ITER reference value (delta similar to 0.5), and (b) in plasmas at low triangularity (delta similar to 0.2) by seeding of Ar and placing the X-point of the plasma on the top of the septum. Pellet injection from the high field side is a third method yielding high density and high confinement, albeit not yet under steady-state conditions. In highly triangular plasmas the influence of input power, plasma triangularity and impurity seeding with noble gases has been studied. Density profile peaking at high densities has been obtained in (a) impurity seeded low triangularity discharges, (b) ELMy H-modes with low levels of input power and (c) discharges fuelled with pellet injection from the high field side. New ELM behaviour has been observed in high triangularity discharges at high density, opening a possible route to ELM heat load mitigation, which can be further amplified by Ar impurity seeding. Current extrapolations of the ELM heat load to ITER show possibly a window for Type I ELM operation. Confinement scaling studies indicate an increase in confinement with triangularity and density peaking, and a decrease in confinement with the Greenwald number. In addition, experiments in H isotope and He indicate tau(E) proportional to M(0.19)Z(-0.59). The threshold power for the L-H transition in He plasmas shows the same parametric dependence as in D plasmas, but with a 50% higher absolute value.
|
|
25. |
- Pamela, J., et al.
(author)
-
Overview of JET results
- 2003
-
In: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 43:12, s. 1540-1554
-
Journal article (peer-reviewed)abstract
- Scientific and technical activities on JET focus on the issues likely to affect the ITER design and operation. Our understanding of the ITER reference mode of operation, the ELMy H-mode, has progressed significantly. The extrapolation of ELM size to ITER has been re-evaluated. Neoclassical tearing modes have been shown to be meta-stable in JET, and their beta limits can be raised by destabilization (modification) of sawteeth by ion cyclotron radio frequency heating (ICRH). Alpha simulation experiments with ICRH accelerated injected 4 (He) beam ions provide a new tool for fast particle and magnetohydrodynamic studies, with up to 80-90% of plasma heating by fast 4 He ions. With or without impurity seeding, a quasi-steady-state high confinement (H-98 = 1), high density(n(e)/n(GW) = 0.9-1) and high beta (betaN = 2) ELMy H-mode has been achieved by operating near the ITER triangularity ( similar to 0.40-0.5) and safety factor (q(95) similar to 3), at Z(eff) similar to 1.5-2. In advanced tokamak (AT) scenarios, internal transport barriers (ITBs) are now characterized in real time with a new criterion, rhoT(*). Tailoring of the current profile with T lower hybrid current drive provides reliable access to a variety of q profiles, lowering access power for barrier formation. Rational q surfaces appear to be associated with ITB formation. Alfven cascades were observed in reversed shear plasmas, providing identification of q profile evolution. Plasmas with 'current holes' were observed and modelled. Transient high confinement AT regimes with H-89 = 3.3, beta(N) = 2.4 and ITER-relevant q < 5 were achieved with reversed magnetic shear. Quasi-stationary ITBs are developed with full non-inductive current drive, including similar to 50% bootstrap current. A record duration of ITBs was achieved, up to 11 s, approaching the resistive time. For the first time, pressure and current profiles of AT regimes are controlled by a real-time feedback system, in separate experiments. Erosion and co-deposition studies with a quartz micro-balance show reduced co-deposition. Measured divertor thermal loads during disruptions in JET could modify ITER assumptions.
|
|