| 1. |
- Abel, I, et al.
(author)
-
Overview of the JET results with the ITER-like wall
- 2013
-
In: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10, s. 104002-
-
Journal article (peer-reviewed)abstract
- Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Z(eff) (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. The re-establishment of the baseline H-mode and hybrid scenarios compatible with the new wall has required an optimization of the control of metallic impurity sources and heat loads. Stable type-I ELMy H-mode regimes with H-98,H-y2 close to 1 and beta(N) similar to 1.6 have been achieved using gas injection. ELM frequency is a key factor for the control of the metallic impurity accumulation. Pedestal temperatures tend to be lower with the new wall, leading to reduced confinement, but nitrogen seeding restores high pedestal temperatures and confinement. Compared with the carbon wall, major disruptions with the new wall show a lower radiated power and a slower current quench. The higher heat loads on Be wall plasma-facing components due to lower radiation made the routine use of massive gas injection for disruption mitigation essential.
|
|
| 2. |
- Romanelli, F, et al.
(author)
-
Overview of the JET results
- 2011
-
In: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 51:9
-
Journal article (peer-reviewed)abstract
- Since the last IAEA Conference JET has been in operation for one year with a programmatic focus on the qualification of ITER operating scenarios, the consolidation of ITER design choices and preparation for plasma operation with the ITER-like wall presently being installed in JET. Good progress has been achieved, including stationary ELMy H-mode operation at 4.5 MA. The high confinement hybrid scenario has been extended to high triangularity, lower ρ*and to pulse lengths comparable to the resistive time. The steady-state scenario has also been extended to lower ρ*and ν*and optimized to simultaneously achieve, under stationary conditions, ITER-like values of all other relevant normalized parameters. A dedicated helium campaign has allowed key aspects of plasma control and H-mode operation for the ITER non-activated phase to be evaluated. Effective sawtooth control by fast ions has been demonstrated with3He minority ICRH, a scenario with negligible minority current drive. Edge localized mode (ELM) control studies using external n = 1 and n = 2 perturbation fields have found a resonance effect in ELM frequency for specific q95values. Complete ELM suppression has, however, not been observed, even with an edge Chirikov parameter larger than 1. Pellet ELM pacing has been demonstrated and the minimum pellet size needed to trigger an ELM has been estimated. For both natural and mitigated ELMs a broadening of the divertor ELM-wetted area with increasing ELM size has been found. In disruption studies with massive gas injection up to 50% of the thermal energy could be radiated before, and 20% during, the thermal quench. Halo currents could be reduced by 60% and, using argon/deuterium and neon/deuterium gas mixtures, runaway electron generation could be avoided. Most objectives of the ITER-like ICRH antenna have been demonstrated; matching with closely packed straps, ELM resilience, scattering matrix arc detection and operation at high power density (6.2 MW m-2) and antenna strap voltages (42 kV). Coupling measurements are in very good agreement with TOPICA modelling. © 2011 IAEA, Vienna.
|
|
| 3. |
- Fenstermacher, M.E., et al.
(author)
-
DIII-D research advancing the physics basis for optimizing the tokamak approach to fusion energy
- 2022
-
In: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 62:4
-
Journal article (peer-reviewed)abstract
- DIII-D physics research addresses critical challenges for the operation of ITER and the next generation of fusion energy devices. This is done through a focus on innovations to provide solutions for high performance long pulse operation, coupled with fundamental plasma physics understanding and model validation, to drive scenario development by integrating high performance core and boundary plasmas. Substantial increases in off-axis current drive efficiency from an innovative top launch system for EC power, and in pressure broadening for Alfven eigenmode control from a co-/counter-I p steerable off-axis neutral beam, all improve the prospects for optimization of future long pulse/steady state high performance tokamak operation. Fundamental studies into the modes that drive the evolution of the pedestal pressure profile and electron vs ion heat flux validate predictive models of pedestal recovery after ELMs. Understanding the physics mechanisms of ELM control and density pumpout by 3D magnetic perturbation fields leads to confident predictions for ITER and future devices. Validated modeling of high-Z shattered pellet injection for disruption mitigation, runaway electron dissipation, and techniques for disruption prediction and avoidance including machine learning, give confidence in handling disruptivity for future devices. For the non-nuclear phase of ITER, two actuators are identified to lower the L-H threshold power in hydrogen plasmas. With this physics understanding and suite of capabilities, a high poloidal beta optimized-core scenario with an internal transport barrier that projects nearly to Q = 10 in ITER at ∼8 MA was coupled to a detached divertor, and a near super H-mode optimized-pedestal scenario with co-I p beam injection was coupled to a radiative divertor. The hybrid core scenario was achieved directly, without the need for anomalous current diffusion, using off-axis current drive actuators. Also, a controller to assess proximity to stability limits and regulate β N in the ITER baseline scenario, based on plasma response to probing 3D fields, was demonstrated. Finally, innovative tokamak operation using a negative triangularity shape showed many attractive features for future pilot plant operation.
|
|
| 4. |
-
- 2019
-
Journal article (peer-reviewed)
|
|
| 5. |
|
|
| 6. |
|
|
| 7. |
|
|
| 8. |
- Mavaddat, Nasim, et al.
(author)
-
Prediction of Breast Cancer Risk Based on Profiling With Common Genetic Variants
- 2015
-
In: Journal of the National Cancer Institute. - : Oxford University Press (OUP). - 1460-2105 .- 0027-8874. ; 107:5, s. 036-036
-
Journal article (peer-reviewed)abstract
- Background: Data for multiple common susceptibility alleles for breast cancer may be combined to identify women at different levels of breast cancer risk. Such stratification could guide preventive and screening strategies. However, empirical evidence for genetic risk stratification is lacking. Methods: We investigated the value of using 77 breast cancer-associated single nucleotide polymorphisms (SNPs) for risk stratification, in a study of 33 673 breast cancer cases and 33 381 control women of European origin. We tested all possible pair-wise multiplicative interactions and constructed a 77-SNP polygenic risk score (PRS) for breast cancer overall and by estrogen receptor (ER) status. Absolute risks of breast cancer by PRS were derived from relative risk estimates and UK incidence and mortality rates. Results: There was no strong evidence for departure from a multiplicative model for any SNP pair. Women in the highest 1% of the PRS had a three-fold increased risk of developing breast cancer compared with women in the middle quintile (odds ratio [OR] = 3.36, 95% confidence interval [CI] = 2.95 to 3.83). The ORs for ER-positive and ER-negative disease were 3.73 (95% CI = 3.24 to 4.30) and 2.80 (95% CI = 2.26 to 3.46), respectively. Lifetime risk of breast cancer for women in the lowest and highest quintiles of the PRS were 5.2% and 16.6% for a woman without family history, and 8.6% and 24.4% for a woman with a first-degree family history of breast cancer. Conclusions: The PRS stratifies breast cancer risk in women both with and without a family history of breast cancer. The observed level of risk discrimination could inform targeted screening and prevention strategies. Further discrimination may be achievable through combining the PRS with lifestyle/environmental factors, although these were not considered in this report.
|
|
| 9. |
|
|
| 10. |
- Imran, Z., et al.
(author)
-
Excellent humidity sensing properties of cadmium titanate nanofibers
- 2013
-
In: Ceramics International. - : Elsevier. - 0272-8842 .- 1873-3956. ; 39:1, s. 457-462
-
Journal article (peer-reviewed)abstract
- We report humidity sensing characteristics of CdTiO3 nanofibers prepared by electrospinning. The nanofibers were porous having an average diameter and length of similar to 50-200 nm and similar to 100 mu m, respectively. The nanofiber humidity sensor was fabricated by defining aluminum electrodes using photolithography on top of the nanofibers deposited on glass substrate. The performance of the CdTiO3 nanofiber humidity sensor was evaluated by AC electrical characterization from 40% to 90% relative humidity at 25 degrees C. The frequency of the AC signal was varied from 10(-1) to 10(6) Hz. Fast response time and recovery time of 4 s and 6 s were observed, respectively. The sensor was highly sensitive and exhibited a reversible response with small hysteresis of less than 7%. Long term stability of the sensor was confirmed during 30 day test. The excellent sensing characteristics prove that the CdTiO3 nanofibers are potential candidate for use in high performance humidity sensors.
|
|
| 11. |
- Purrington, Kristen S., et al.
(author)
-
Genome-wide association study identifies 25 known breast cancer susceptibility loci as risk factors for triple-negative breast cancer
- 2014
-
In: Carcinogenesis. - : Oxford University Press (OUP). - 0143-3334 .- 1460-2180. ; 35:5, s. 1012-1019
-
Journal article (peer-reviewed)abstract
- In a genome-wide scan, we show that 30 variants in 25 genomic regions are associated with risk of TN breast cancer. Women carrying many of the risk variants may have 4-fold increased risk relative to women with few variants.Triple-negative (TN) breast cancer is an aggressive subtype of breast cancer associated with a unique set of epidemiologic and genetic risk factors. We conducted a two-stage genome-wide association study of TN breast cancer (stage 1: 1529 TN cases, 3399 controls; stage 2: 2148 cases, 1309 controls) to identify loci that influence TN breast cancer risk. Variants in the 19p13.1 and PTHLH loci showed genome-wide significant associations (P < 5 x 10(-) (8)) in stage 1 and 2 combined. Results also suggested a substantial enrichment of significantly associated variants among the single nucleotide polymorphisms (SNPs) analyzed in stage 2. Variants from 25 of 74 known breast cancer susceptibility loci were also associated with risk of TN breast cancer (P < 0.05). Associations with TN breast cancer were confirmed for 10 loci (LGR6, MDM4, CASP8, 2q35, 2p24.1, TERT-rs10069690, ESR1, TOX3, 19p13.1, RALY), and we identified associations with TN breast cancer for 15 additional breast cancer loci (P < 0.05: PEX14, 2q24.1, 2q31.1, ADAM29, EBF1, TCF7L2, 11q13.1, 11q24.3, 12p13.1, PTHLH, NTN4, 12q24, BRCA2, RAD51L1-rs2588809, MKL1). Further, two SNPs independent of previously reported signals in ESR1 [rs12525163 odds ratio (OR) = 1.15, P = 4.9 x 10(-) (4)] and 19p13.1 (rs1864112 OR = 0.84, P = 1.8 x 10(-) (9)) were associated with TN breast cancer. A polygenic risk score (PRS) for TN breast cancer based on known breast cancer risk variants showed a 4-fold difference in risk between the highest and lowest PRS quintiles (OR = 4.03, 95% confidence interval 3.46-4.70, P = 4.8 x 10(-) (69)). This translates to an absolute risk for TN breast cancer ranging from 0.8% to 3.4%, suggesting that genetic variation may be used for TN breast cancer risk prediction.
|
|
| 12. |
- Sator, Lea, et al.
(author)
-
Overdiagnosis of COPD in Subjects With Unobstructed Spirometry A BOLD Analysis
- 2019
-
In: Chest. - : Elsevier BV. - 0012-3692 .- 1931-3543. ; 156:2, s. 277-288
-
Journal article (peer-reviewed)abstract
- BACKGROUND: There are several reports on underdiagnosis of COPD, while little is known about COPD overdiagnosis and overtreatment. We describe the overdiagnosis and the prevalence of spirometrically defined false positive COPD, as well as their relationship with overtreatment across 23 population samples in 20 countries participating in the BOLD Study between 2003 and 2012.METHODS: A false positive diagnosis of COPD was considered when participants reported a doctor's diagnosis of COPD, but postbronchodilator spirometry was unobstructed (FEV1/FVC > LLN). Additional analyses were performed using the fixed ratio criterion (FEV1/FVC < 0.7).RESULTS: Among 16,177 participants, 919 (5.7%) reported a previous medical diagnosis of COPD. Postbronchodilator spirometry was unobstructed in 569 subjects (61.9%): false positive COPD. A similar rate of overdiagnosis was seen when using the fixed ratio criterion (55.3%). In a subgroup analysis excluding participants who reported a diagnosis of "chronic bronchitis" or "emphysema" (n = 220), 37.7% had no airflow limitation. The site-specific prevalence of false positive COPD varied greatly, from 1.9% in low- to middle-income countries to 4.9% in high-income countries. In multivariate analysis, overdiagnosis was more common among women, and was associated with higher education; former and current smoking; the presence of wheeze, cough, and phlegm; and concomitant medical diagnosis of asthma or heart disease. Among the subjects with false positive COPD, 45.7% reported current use of respiratory medication. Excluding patients with reported asthma, 34.4% of those with normal spirometry still used a respiratory medication.CONCLUSIONS: False positive COPD is frequent. This might expose nonobstructed subjects to possible adverse effects of respiratory medication.
|
|
| 13. |
|
|
| 14. |
- Batool, S S., et al.
(author)
-
Comparative Analysis of Ti, Ni, and Au Electrodes on Characteristics of TiO2 Nanofibers for Humidity Sensor Application
- 2013
-
In: Journal of Materials Science & Technology. - : Elsevier. - 1005-0302. ; 29:5, s. 411-414
-
Journal article (peer-reviewed)abstract
- The effect of metal (Ti, Ni, and Au) electrodes on humidity sensing properties of electrospun TiO2 nanofibers was investigated in this work. The devices were fabricated by evaporating metal contacts on SiO2 layer thermally grown on silicon substrate. The separation between the electrodes was 90 mm for all sensors. The sensors were tested from 40% to 90% relative humidity (RH) by AC electrical characterization at room temperature. When sensors are switched between 40% and 90% RH, the corresponding response and recovery time are 3 s and 5 s for Ti-electrode sensor, 4 s and 7 s for Ni-electrode sensor, and 7 s and 13 s for Au-electrode sensor. The hysteresis was 3%, 5% and 15% for Ti-, Ni-, and Au-electrode sensor, respectively. The sensitivity of Ti, Ni, and Au-electrode sensors are 7.53 M Omega/% RH, 5.29 MU/% RH and 4.01 M Omega/% RH respectively at 100 Hz. Therefore Ti-electrode sensor is found to have linear response, fast response and recovery time and higher sensitivity as compared with those of Ni- and Au-electrode sensors. Comparison of humidity sensing properties of sensors with different electrode material may propose a compelling route for designing and optimizing humidity sensors.
|
|
| 15. |
- Batool, S S., et al.
(author)
-
Investigation of dielectric relaxation behavior of electrospun titanium dioxide nanofibers using temperature dependent impedance spectroscopy
- 2013
-
In: Ceramics International. - : Elsevier. - 0272-8842 .- 1873-3956. ; 39:2, s. 1775-1783
-
Journal article (peer-reviewed)abstract
- The electrospinning method has been utilized in the fabrication of titanium dioxide nanofibers (TNFs) with an average diameter of similar to 50 nm and length of 100 um. Effect of temperature on the dielectric relaxation behavior of the fabricated nanofibers have been studied using AC impedance spectroscopy. The morphological, structural and compositional aspects as well as the optical properties of the TNFs have been investigated by field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), energy-dispersive x-ray spectroscopy (EDX) and ultraviolet visible (UV vis) absorption spectrum. The permittivity behavior of the device at the frequency below 10(2) Hz shows the relaxation contribution along with the electrode polarization. Dielectric loss peak in loss tangent also confirms the presence of relaxing dipoles in TNFs. The AC conductance as a function of frequency confirms the semiconducting nature of TNFs and obeys Jonschers power law except a small deviation in the low frequency region. DC conductivity increases with increase in temperature.
|
|
| 16. |
- Batool, S S, et al.
(author)
-
Silica nanofibers based impedance type humidity detector prepared on glass substrate
- 2013
-
In: Vacuum. - : Elsevier. - 0042-207X .- 1879-2715. ; 87, s. 1-6
-
Journal article (peer-reviewed)abstract
- Impedance type relative humidity detector is fabricated by depositing electrospun silica nanofibers on glass substrate. The silica nanofibers with an average diameter similar to 150 nm and length similar to 100 mu m were used. Thermogravimetric and differential scanning calorimetric analysis confirm that the accurate annealing temperature is 500 degrees C for complete removal of PVP. Humidity detecting devices were fabricated by defining titanium electrodes on top of the silica nanofibers. The performance of silica nanofibers humidity detectors was tested by AC electrical measurements at 40-90% relative humidity. The response and the recovery times were 5 s and 3 s, respectively, between 40% and 90% relative humidity. Contribution of dipoles, space charge polarization, relaxation of these dipoles and low frequency dispersion phenomenon were observed during impedance measurements.
|
|
| 17. |
- Imran, Z, et al.
(author)
-
Fabrication of cadmium titanate nanofibers via electrospinning technique
- 2012
-
In: Ceramics International. - : Elsevier. - 0272-8842 .- 1873-3956. ; 38:4, s. 3361-3365
-
Journal article (peer-reviewed)abstract
- Here we present an electrospinning technique for the fabrication of cadmium titanate/polyvinyl-pyrrolidone composite nanofibers. The composite nanofibers are then annealed at 600 degrees C to obtain ilmenite rhombohedral phase cadmium titanate nanofibers. The structure, composition, thermal stability and optical properties of as synthesized and annealed cadmium titanate nanofibers are characterized by X-ray diffraction, energy dispersive X-ray spectroscopy, scanning electron microscopy, transmission electron microscopy, thermogravimetric analysis, Fourier transform infrared spectroscopy and ultraviolet-visible spectroscopy. The average diameter and length of the nanofibers are found to be similar to 150-200 nm and similar to 100 mu m, respectively.
|
|
| 18. |
- Madsen, C. L., et al.
(author)
-
The left atrial appendage closure by surgery-2 (LAACS-2) trial protocol rationale and design of a randomized multicenter trial investigating if left atrial appendage closure prevents stroke in patients undergoing open-heart surgery irrespective of preoperative atrial fibrillation status and stroke risk
- 2023
-
In: American Heart Journal. - 0002-8703. ; 264, s. 133-142
-
Journal article (peer-reviewed)abstract
- Background Current recommendations regarding the use of surgical left atrial appendage (IAA) closure to prevent thromboembolisms lack high-level evidence. Patients undergoing open-heart surgery often have several cardiovascular risk factors and a high occurrence of postoperative atrial fibrillation (AF)-with a high recurrence rate-and are thus at a high risk of stroke. Therefore, we hypothesized that concomitant IAA closure during open-heart surgery will reduce mid-term risk of stroke independently of preoperative AF status and CHA 2 DS 2 -VASc score. Methods This protocol describes a randomized multicenter trial. Consecutive participants & GE;18 years scheduled for first-time planned open-heart surgery from cardiac surgery centers in Denmark, Spain, and Sweden are included. Both patients with a previous diagnosis of paroxysmal or chronic AF, as well as those without AF, are eligible to participate, irrespective of their CHA 2 DS 2 -VASc score. Patients already planned for ablation or IAA closure during surgery, with current endocarditis, or where follow-up is not possible are considered noneligible. Patients are stratified by site, surgery type, and preoperative or planned oral anticoagulation treatment. Subsequently, patients are randomized 1:1 to either concomitant IAA closure or standard care (ie, open IAA). The primary outcome is stroke, including transient ischemic attack, as assigned by 2 independent neurologists blinded to the treatment allocation. To recognize a 60% relative risk reduction of the primary outcome with LAA closure, 1,500 patients are randomized and followed for 2 years (significance level of 0.05 and power of 90%). Conclusions The LAACS-2 trial is likely to impact the LAA closure approach in most patients undergoing open-heart surgery. Trial registration: NCT03724318. (Am HeartJ 2023;264:133-142.)
|
|
| 19. |
- Roberts, Jason D., et al.
(author)
-
Ankyrin-B dysfunction predisposes to arrhythmogenic cardiomyopathy and is amenable to therapy
- 2019
-
In: Journal of Clinical Investigation. - : AMER SOC CLINICAL INVESTIGATION INC. - 0021-9738 .- 1558-8238. ; 129:8, s. 3171-3184
-
Journal article (peer-reviewed)abstract
- Arrhythmogenic cardiomyopathy (ACM) is an inherited arrhythmia syndrome characterized by severe structural and electrical cardiac phenotypes, including myocardial fibrofatty replacement and sudden cardiac death. Clinical management of ACM is largely palliative, owing to an absence of therapies that target its underlying pathophysiology, which stems partially from our limited insight into the condition. Following identification of deceased ACM probands possessing ANK2 rare variants and evidence of ankyrin-B loss of function on cardiac tissue analysis, an ANK2 mouse model was found to develop dramatic structural abnormalities reflective of human ACM, including biventricular dilation, reduced ejection fraction, cardiac fibrosis, and premature death. Desmosomal structure and function appeared preserved in diseased human and murine specimens in the presence of markedly abnormal beta-catenin expression and patterning, leading to identification of a previously unknown interaction between ankyrin-B and beta-catenin. A pharmacological activator of the WNT/beta-catenin pathway, SB-216763, successfully prevented and partially reversed the murine ACM phenotypes. Our findings introduce what we believe to be a new pathway for ACM, a role of ankyrin-B in cardiac structure and signaling, a molecular link between ankyrin-B and beta-catenin, and evidence for targeted activation of the WNT/beta-catenin pathway as a potential treatment for this disease.
|
|
| 20. |
|
|
| 21. |
|
|
| 22. |
- Aziz, Maria, et al.
(author)
-
Efficient Removal of Lead and Chromium From Aqueous Media Using Selenium Based Nanocomposite Supported by Orange Peel
- 2022
-
In: Frontiers in Environmental Science. - : Frontiers Media S.A.. - 2296-665X. ; 10
-
Journal article (peer-reviewed)abstract
- This study presents the synthesis of activated orange peel, derived from bio-waste (orange peel) and its doping with selenium nano-particles to enhance the adsorption capacity. The synthesized nanocomposite orange peel/Selenium (OP/Se) was applied as adsorbents for the removal of Lead (Pb) and Chromium (Cr) from synthetic waste water as an economical water cleaning technology. Orange peel/Selenium nanocomposite was characterized by X-Ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR) and Scanning electron microscopy (SEM). Scanning electron microscopy results showed the porous structure of OP/Se nanocomposite and distinct peaks observed in XRD and FTIR spectra depicted the successful synthesis of nanocomposite. Batch experiments were conducted to figure out the effect of different parameters on adsorption of Pb and Cr by using Atomic Absorption Spectroscopy. The maximum adsorption capacity of 99.9% was achieved for both lead and chromium at acidic pH. While at temperature of 60°C the maximum adsorption of 98.3 and 95.9% was found for Pb and Cr respectively. Furthermore the experimental data was examined with Pseudo-first order, first-order and Pseudo-second order kinetic model, as well as Morris Intraparticle diffusion model where the pseudo second order was best fitted which indicated the chemisorption mechanism in adsorption process. The adsorption process followed the Langmuir isotherm model verified that OP/Se nanocomposite was found to be favorable for the process of adsorption. The adsorption thermodynamics indicate that adsorption of heavy metals ions is spontaneous (ΔG° < 0) and the adsorption increases with increase in temperature which means that reaction was endothermic in nature. This study revealed that the synthesized bio-activated nanocomposite was an efficient adsorbent material for the removal of heavy metals from waste water.
|
|
| 23. |
- Ovaskainen, Otso, et al.
(author)
-
Global Spore Sampling Project: A global, standardized dataset of airborne fungal DNA
- 2024
-
In: Scientific Data. - 2052-4463. ; 11
-
Journal article (peer-reviewed)abstract
- Novel methods for sampling and characterizing biodiversity hold great promise for re-evaluating patterns of life across the planet. The sampling of airborne spores with a cyclone sampler, and the sequencing of their DNA, have been suggested as an efficient and well-calibrated tool for surveying fungal diversity across various environments. Here we present data originating from the Global Spore Sampling Project, comprising 2,768 samples collected during two years at 47 outdoor locations across the world. Each sample represents fungal DNA extracted from 24 m3 of air. We applied a conservative bioinformatics pipeline that filtered out sequences that did not show strong evidence of representing a fungal species. The pipeline yielded 27,954 species-level operational taxonomic units (OTUs). Each OTU is accompanied by a probabilistic taxonomic classification, validated through comparison with expert evaluations. To examine the potential of the data for ecological analyses, we partitioned the variation in species distributions into spatial and seasonal components, showing a strong effect of the annual mean temperature on community composition.
|
|
| 24. |
- Rafiq, Iqra, et al.
(author)
-
IoT applications and challenges in smart cities and services
- 2023
-
In: The Journal of Engineering. - : John Wiley & Sons. - 2051-3305. ; 2023:4
-
Research review (peer-reviewed)abstract
- Internet of Things (IoT) is a revolutionary and novel platform where a smart network connects to the large number of electronic devices via internet through available communication systems for reliable and real time connectivity, sensing thus acquiring data from sensors, computing and actuating devices. A review of the current status of IoT features, architecture, communication infrastructure and applications is presented here. Number of IoT applications and challenges in the development of smart cities are covered about this innovative technological platform in this review along with communication protocols characteristics and applications. IoT aided smart city services, health applications, transport applications and smart grid improvements are also discussed. Many challenges and issues related to security, communication, applications and system architecture along with future directions of IoT technology are elaborated in detail.
|
|
| 25. |
- Rafiq, M. A., et al.
(author)
-
Mapping of three novel loci for non-syndromic autosomal recessive mental retardation (NS-ARMR) in consanguineous families from Pakistan
- 2010
-
In: Clinical Genetics. - : Wiley. - 0009-9163 .- 1399-0004. ; 78:5, s. 478-483
-
Journal article (peer-reviewed)abstract
- To date, of 13 loci with linkage to non-syndromic autosomal recessive mental retardation (NS-ARMR), only six genes have been established with associated mutations. Here we present our study on NS-ARMR among the Pakistani population, where people are traditionally bound to marry within the family or the wider clan. In an exceptional, far-reaching genetic survey we have collected more than 50 consanguineous families exhibiting clinical symptoms/phenotypes of NS-ARMR. In the first step, nine families (MR2-9 and MR11) with multiple affected individuals were selected for molecular genetic studies. Two families (MR3, MR4) showed linkage to already know NS-ARMR loci. Fifteen affected and 10 unaffected individuals from six (MR2, MR6, MR7, MR8, MR9 and MR11) families were genotyped by using Affymetrix 5.0 or 6.0 single-nucleotide polymorphism (SNP) microarrays. SNP microarray data was visually inspected by dChip and genome-wide homozygosity analysis was performed by HomozygosityMapper. Additional mapping was performed (to exclude false-positive regions of homozygosity called by HomozygosityMapper and dChip) on all available affected and unaffected members in seven NS-ARMR families, using microsatellite markers. In this manner we were able to map three novel loci in seven different families originating from different areas of Pakistan. Two families (MR2, MR5) showed linkage on chromosome 2p25.3-p25.2. Three families (MR7, MR8, and MR9) that have been collected from the same village and belong to the same clan were mapped on chromosome 9q34.3. MR11 maps to a locus on 9p23-p13.3. Analysis of MR6 showed two positive loci, on chromosome 1q23.2-q23.3 and 8q24.21-q24.23. Genotyping in additional family members has so far narrowed, but not excluded the 1q locus. In summary, through this study we have identified three new loci for NS-ARMR, namely MRT14, 15 and 16.
|
|
