| 1. |
- Fan, Qunping, et al.
(författare)
-
10.13% Efficiency All-Polymer Solar Cells Enabled by Improving the Optical Absorption of Polymer Acceptors
- 2020
-
Ingår i: Solar RRL. - : Wiley. - 2367-198X. ; 4:6
-
Tidskriftsartikel (refereegranskat)abstract
- The limited light absorption capacity for most polymer acceptors hinders the improvement of the power conversion efficiency (PCE) of all-polymer solar cells (all-PSCs). Herein, by simultaneously increasing the conjugation of the acceptor unit and enhancing the electron-donating ability of the donor unit, a novel narrow-bandgap polymer acceptor PF3-DTCO based on an A–D–A-structured acceptor unit ITIC16 and a carbon–oxygen (C–O)-bridged donor unit DTCO is developed. The extended conjugation of the acceptor units from IDIC16 to ITIC16 results in a red-shifted absorption spectrum and improved absorption coefficient without significant reduction of the lowest unoccupied molecular orbital energy level. Moreover, in addition to further broadening the absorption spectrum by the enhanced intramolecular charge transfer effect, the introduction of C–O bridges into the donor unit improves the absorption coefficient and electron mobility, as well as optimizes the morphology and molecular order of active layers. As a result, the PF3-DTCO achieves a higher PCE of 10.13% with a higher short-circuit current density (Jsc) of 15.75 mA cm−2 in all-PSCs compared with its original polymer acceptor PF2-DTC (PCE = 8.95% and Jsc = 13.82 mA cm−2). Herein, a promising method is provided to construct high-performance polymer acceptors with excellent optical absorption for efficient all-PSCs.
|
|
| 2. |
- Fan, Qunping, 1989, et al.
(författare)
-
A Non-Conjugated Polymer Acceptor for Efficient and Thermally Stable All-Polymer Solar Cells
- 2020
-
Ingår i: Angewandte Chemie - International Edition. - : Wiley. - 1433-7851 .- 1521-3773. ; 59:45, s. 19835-19840
-
Tidskriftsartikel (refereegranskat)abstract
- A non-conjugated polymer acceptor PF1-TS4 was firstly synthesized by embedding a thioalkyl segment in the mainchain, which shows excellent photophysical properties on par with a fully conjugated polymer, with a low optical band gap of 1.58 eV and a high absorption coefficient >105 cm−1, a high LUMO level of −3.89 eV, and suitable crystallinity. Matched with the polymer donor PM6, the PF1-TS4-based all-PSC achieved a power conversion efficiency (PCE) of 8.63 %, which is ≈45 % higher than that of a device based on the small molecule acceptor counterpart IDIC16. Moreover, the PF1-TS4-based all-PSC has good thermal stability with ≈70 % of its initial PCE retained after being stored at 85 °C for 180 h, while the IDIC16-based device only retained ≈50 % of its initial PCE when stored at 85 °C for only 18 h. Our work provides a new strategy to develop efficient polymer acceptor materials by linkage of conjugated units with non-conjugated thioalkyl segments.
|
|
| 3. |
- Fan, Qunping, 1989, et al.
(författare)
-
High-performance all-polymer solar cells enabled by a novel low bandgap non-fully conjugated polymer acceptor
- 2021
-
Ingår i: Science in China Series B. - : Springer Nature. - 1674-7291 .- 1869-1870. ; 64, s. 1380-1388
-
Tidskriftsartikel (refereegranskat)abstract
- Anon-fully conjugated polymer as a new class of acceptor materials has shown some advantages over its small molecular counterpart when used in photoactive layers for all-polymer solar cells (all-PSCs), despite a low power conversion efficiency (PCE) caused by its narrow absorption spectra. Herein, a novel non-fully conjugated polymer acceptor PFY-2TS with a low bandgap of similar to 1.40 eV was developed, via polymerizing a large pi-fused small molecule acceptor (SMA) building block (namely YBO) with a non-conjugated thioalkyl linkage. Compared with its precursor YBO, PFY-2TS retains a similar low bandgap but a higher LUMO level. Moreover, compared with the structural analog of YBO-based fully conjugated polymer acceptor PFY-DTC, PFY-2TS shows similar absorption spectrum and electron mobility, but significantly different molecular crystallinity and aggregation properties, which results in optimal blend morphology with a polymer donor PBDB-T and better device physical processes in all-PSCs. As a result, PFY-2TS-based all-PSCs achieved a PCE of 12.31% with a small energy loss of 0.56 eV enabled by the reduced non-radiative energy loss (0.24 eV), which is better than that of 11.08% for the PFY-DTC-based ones. Our work clearly demonstrated that non-fully conjugated polymers as a new class of acceptor materials are very promising for the development of high-performance all-PSCs.
|
|
| 4. |
- Fan, Qunping, 1989, et al.
(författare)
-
Mechanically Robust All-Polymer Solar Cells from Narrow Band Gap Acceptors with Hetero-Bridging Atoms
- 2020
-
Ingår i: Joule. - : Elsevier BV. - 2542-4351. ; 4:3, s. 658-672
-
Tidskriftsartikel (refereegranskat)abstract
- We developed three narrow band-gap polymer acceptors PF2-DTC, PF2-DTSi, and PF2-DTGe with different bridging atoms (i.e., C, Si, and Ge). Studies found that such different bridging atoms significantly affect the crystallinity, extinction coefficient, electron mobility of the polymer acceptors, and the morphology and mechanical robustness of related active layers. In all-polymer solar cells (all-PSCs), these polymer acceptors achieved high power conversion efficiencies (PCEs) over 8.0%, while PF2-DTSi obtained the highest PCE of 10.77% due to its improved exciton dissociation, charge transport, and optimized morphology. Moreover, the PF2-DTSi-based active layer showed excellent mechanical robustness with a high toughness value of 9.3 MJ m−3 and a large elongation at a break of 8.6%, which is a great advantage for the practical applications of flexible devices. As a result, the PF2-DTSi-based flexible all-PSC retained >90% of its initial PCE (6.37%) after bending and relaxing 1,200 times at a bending radius of ∼4 mm.
|
|
| 5. |
- Fan, Qunping, 1989, et al.
(författare)
-
Over 14% efficiency all-polymer solar cells enabled by a low bandgap polymer acceptor with low energy loss and efficient charge separation
- 2020
-
Ingår i: Energy & Environmental Science. - : Royal Society of Chemistry. - 1754-5692 .- 1754-5706. ; 13:12, s. 5017-5027
-
Tidskriftsartikel (refereegranskat)abstract
- Obtaining both high open-circuit voltage (V-oc) and short-circuit current density (J(sc)) has been a major challenge for efficient all-polymer solar cells (all-PSCs). Herein, we developed a polymer acceptor PF5-Y5 with excellent optical absorption capability (onset extending to similar to 880 nm and maximum absorption coefficient exceeding 105 cm(-1) in a film), high electron mobility (3.18 x 10(3) cm(2) V-1 s(-1)) and high LUMO level (-3.84 eV) to address such a challenge. As a result, the PBDB-T:PF5-Y5-based all-PSCs achieved a high power conversion efficiency of up to 14.45% with both a high Voc (0.946 V) and a high Jsc (20.65 mA cm(-2)), due to the high and broad absorption coverage, small energy loss (0.57 eV) and efficient charge separation and transport in the device, which are among the best values in the all-PSC field. In addition, the all-PSC shows a similar to 15% improvement in PCE compared to its counterpart small molecule acceptor (Y5)-based device. Our results suggest that PF5-Y5 is a very promising polymer acceptor candidate for applications in efficient all-PSCs.
|
|
| 6. |
- Fan, Qunping, et al.
(författare)
-
Unidirectional Sidechain Engineering to Construct Dual-Asymmetric Acceptors for 19.23 % Efficiency Organic Solar Cells with Low Energy Loss and Efficient Charge Transfer
- 2023
-
Ingår i: Angewandte Chemie International Edition. - : WILEY-V C H VERLAG GMBH. - 1433-7851 .- 1521-3773. ; 62:36
-
Tidskriftsartikel (refereegranskat)abstract
- Achieving both high open-circuit voltage (V-oc) and short-circuit current density (J(sc)) to boost power-conversion efficiency (PCE) is a major challenge for organic solar cells (OSCs), wherein high energy loss (E-loss) and inefficient charge transfer usually take place. Here, three new Y-series acceptors of mono-asymmetric asy-YC11 and dual-asymmetric bi-asy-YC9 and bi-asy-YC12 are developed. They share the same asymmetric D(1)AD(2) (D-1=thieno[3,2-b]thiophene and D-2=selenopheno[3,2-b]thiophene) fused-core but have different unidirectional sidechain on D-1 side, allowing fine-tuned molecular properties, such as intermolecular interaction, packing pattern, and crystallinity. Among the binary blends, the PM6 : bi-asy-YC12 one has better morphology with appropriate phase separation and higher order packing than the PM6 : asy-YC9 and PM6 : bi-asy-YC11 ones. Therefore, the PM6 : bi-asy-YC12-based OSCs offer a higher PCE of 17.16 % with both high V-oc and J(sc), due to the reduced E-loss and efficient charge transfer properties. Inspired by the high V-oc and strong NIR-absorption, bi-asy-YC12 is introduced into efficient binary PM6 : L8-BO to construct ternary OSCs. Thanks to the broadened absorption, optimized morphology, and furtherly minimized E-loss, the PM6 : L8-BO : bi-asy-YC12-based OSCs achieve a champion PCE of 19.23 %, which is one of the highest efficiencies among these annealing-free devices. Our developed unidirectional sidechain engineering for constructing bi-asymmetric Y-series acceptors provides an approach to boost PCE of OSCs.
|
|
| 7. |
- Fan, Qunping, 1989, et al.
(författare)
-
Weak Makes It Powerful: The Role of Cognate Small Molecules as an Alloy Donor in 2D/1A Ternary Fullerene Solar Cells for Finely Tuned Hierarchical Morphology in Thick Active Layers
- 2020
-
Ingår i: Small Methods. - : Wiley. - 2366-9608. ; 4:3
-
Tidskriftsartikel (refereegranskat)abstract
- Herein, a novel small molecule donor is first developed, FSM6, which is a cognate molecule to BTR possessing similar molecular structure with comparable optical absorption but different crystallinity. The efficient fullerene-type ternary small molecular solar cells (SMSCs) based on an alloy donor of BTR and FSM6 in a thick film of 250 nm reveal the improved hierarchical phase separation morphology and molecular structural order of ternary active layers with improved crystallinity of the key donor component BTR. Furthermore, FSM6 as the key third component also plays a role of charge transfer accelerator in ternary SMSCs. As a result, the optimal ternary SMSCs based on BTR:FSM6:PC71BM achieve a high power conversion efficiency (PCE) up to 10.21% with the synergistically improved open-circuit voltage of 0.950 V, short-circuit current density of 13.85 mA cm(-2), and fill factor of 77.6%, in comparison with either the binary SMSCs of BTR:PC71BM (PCE = 9.37%) or FSM6:PC71BM (PCE = 8.00%). This work provides a promising methodology to optimize device morphology for high-performance ternary SMSCs by combining two cognate small molecules with similar absorption spectra but different crystallinity as an alloy donor.
|
|
| 8. |
- Hu, Wei, et al.
(författare)
-
Axisymmetric and Asymmetric Naphthalene-Bisthienothiophene Based Nonfullerene Acceptors: On Constitutional Isomerization and Photovoltaic Performance
- 2020
-
Ingår i: ACS Applied Energy Materials. - : American Chemical Society (ACS). - 2574-0962. ; 3:6, s. 5734-5744
-
Tidskriftsartikel (refereegranskat)abstract
- Two pairs of constitutional isomers of fused-octacyclic nonfullerene acceptors (NFAs) based on a naphthalene-bisthienothiophene core with or without fluorination at the ending groups have been developed. Compared with the axisymmetric NFAs N66-IC and N66-2FIC with two six-member-ring bridges, their asymmetric constitutional isomers N65-IC and N65-2FIC both with one six-member-ring bridge and one five-member-ring bridge exhibit remarkable red-shifted absorption, higher crystallinity, and slightly down-shifted LUMO energy levels. Organic solar cells based on PBDB-T-2F:N65-2FIC achieved a promising power conversion efficiency of 10.19%, which is three times higher than that of its counterpart PBDB-T-2F:N66-2FIC cell (3.46%). While being blended with PBDB-T as the donor material, the asymmetric acceptor analogue N65-IC based solar cell pronounces a PCE of 9.03%, being significantly improved from that of 5.45% for the PBDB-T:N66-IC based cell, which is in consistency with the results from those cells from their both fluorinated donor and acceptor counterparts. Design rules on either both fluorinated, both nonfluorinated, or cross-combined donor/acceptors for device fabrication has been explored. In addition, PBDB-T-2F:N65-2FIC possesses very promising device stability with 85% of its initial PCE after an exposure time of 1500 h under one sun illumination, which is meaningful for their future commercial devices.
|
|
| 9. |
- Liu, Shungang, et al.
(författare)
-
The role of connectivity in significant bandgap narrowing for fused-pyrene based non-fullerene acceptors toward high-efficiency organic solar cells
- 2020
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry (RSC). - 2050-7488 .- 2050-7496. ; 8:12, s. 5995-6003
-
Tidskriftsartikel (refereegranskat)abstract
- Great attention has been paid to developing low bandgap non-fullerene acceptors (NFAs) for matching wide bandgap donor polymers to increase the photocurrent and therefore the power conversion efficiencies (PCEs) of NFA organic solar cells, while pyrene-core based acceptor-donor-acceptor (A-D-A) NFAs have been mainly reported via the 2,9-position connection due to their bisthieno[3′,2′-b']thienyl[a,h]pyrene fused via a five-membered ring bridge at the ortho-position of pyrene as the representative one named FPIC5, which has prohibited further narrowing their energy gap. Herein, an acceptor FPIC6 was exploited by creating the 1,8-position connection through fusing as bisthieno[3′,2′-b′]thienyl[f-g,m-n]pyrene linked at the bay-position via a six-membered bridge, with enhanced push-pull characteristics within such A-D-A structure. As a structural isomer of FPIC5, FPIC6 exhibited a much lower bandgap of 1.42 eV (1.63 eV for FPIC5). Therefore, the photocurrent and PCE of PTB7-Th:FPIC6 cells were improved to 21.50 mA cm-2 and 11.55%, respectively, due to the balanced mobilities, better photoluminescence quenching efficiency and optimized morphology, which are both ∼40% better than those of PTB7-Th:FPIC5 cells. Our results clearly proved that a pyrene fused core with 1,8-position connection with electron-withdrawing end groups instead of 2,9-position connection is an efficient molecular design strategy to narrow the optical bandgap and improve the photovoltaic performance of NFA based OSCs.
|
|
| 10. |
- Ma, Ruijie, et al.
(författare)
-
All-polymer solar cells with over 16% efficiency and enhanced stability enabled by compatible solvent and polymer additives
- 2022
-
Ingår i: Aggregate. - : Wiley. - 2692-4560 .- 2766-8541. ; 3:3
-
Tidskriftsartikel (refereegranskat)abstract
- Considering the robust and stable nature of the active layers, advancing the power conversion efficiency (PCE) has long been the priority for all-polymer solar cells (all-PSCs). Despite the recent surge of PCE, the photovoltaic parameters of the state-of-the-art all-PSC still lag those of the polymer:small molecule-based devices. To compete with the counterparts, judicious modulation of the morphology and thus the device electrical properties are needed. It is difficult to improve all the parameters concurrently for the all-PSCs with advanced efficiency, and one increase is typically accompanied by the drop of the other(s). In this work, with the aids of the solvent additive (1-chloronaphthalene) and the n-type polymer additive (N2200), we can fine-tune the morphology of the active layer and demonstrate a 16.04% efficient all-PSC based on the PM6:PY-IT active layer. The grazing incidence wide-angle X-ray scattering measurements show that the shape of the crystallites can be altered, and the reshaped crystallites lead to enhanced and more balanced charge transport, reduced recombination, and suppressed energy loss, which lead to concurrently improved and device efficiency and stability.
|
|
| 11. |
- Su, Wenyan, et al.
(författare)
-
13.4 % Efficiency from All-Small-Molecule Organic Solar Cells Based on a Crystalline Donor with Chlorine and Trialkylsilyl Substitutions
- 2021
-
Ingår i: ChemSusChem. - : Wiley. - 1864-5631 .- 1864-564X. ; 14:17, s. 3535-3543
-
Tidskriftsartikel (refereegranskat)abstract
- How to simultaneously achieve both high open-circuit voltage (Voc) and high short-circuit current density (Jsc) is a big challenge for realising high power conversion efficiency (PCE) in all-small-molecule organic solar cells (all-SM OSCs). Herein, a novel small molecule (SM)-donor, namely FYSM−SiCl, with trialkylsilyl and chlorine substitutions was designed and synthesized. Compared to the original SM-donor FYSM−H, FYSM−Si with trialkylsilyl substitution showed a decreased crystallinity and lower highest occupied molecular orbital (HOMO) level, while FYSM−SiCl had an improved crystallinity, more ordered packing arrangement, significantly lower HOMO level, and predominant “face-on” orientation. Matched with a SM-acceptor Y6, the FYSM−SiCl-based all-SM OSCs exhibited both high Voc of 0.85 V and high Jsc of 23.7 mA cm−2, which is rare for all-SM OSCs and could be attributed to the low HOMO level of FYSM−SiCl donor and the delicate balance between high crystallinity and suitable blend morphology. As a result, FYSM−SiCl achieved a high PCE of 13.4 % in all-SM OSCs, which was much higher than those of the FYSM−H- (10.9 %) and FYSM−Si-based devices (12.2 %). This work demonstrated a promising method for the design of efficient SM-donors by a side-chain engineering strategy via the introduction of trialkylsilyl and chlorine substitutions.
|
|
| 12. |
|
|
| 13. |
- Su, Wenyan, et al.
(författare)
-
Nonconjugated Terpolymer Acceptors with Two Different Fused-Ring Electron-Deficient Building Blocks for Efficient All-Polymer Solar Cells
- 2021
-
Ingår i: ACS Applied Materials and Interfaces. - : American Chemical Society (ACS). - 1944-8244 .- 1944-8252. ; 13:5, s. 6442-6449
-
Tidskriftsartikel (refereegranskat)abstract
- The ternary polymerization strategy of incorporating different donor and acceptor units forming terpolymers as photovoltaic materials has been proven advantageous in improving power conversion efficiencies (PCEs) of polymer solar cells (PSCs). Herein, a series of low band gap nonconjugated terpolymer acceptors based on two different fused-ring electron-deficient building blocks (IDIC16 and ITIC) with adjustable photoelectric properties were developed. As the third component, ITIC building blocks with a larger pi-conjugation structure, shorter solubilizing side chains, and red-shifted absorption spectrum were incorporated into an IDIC16-based nonconjugated copolymer acceptor PF1-TS4, which built up the terpolymers with two conjugated building blocks linked by flexible thioalkyl chain-thiophene segments. With the increasing ITIC content, terpolymers show gradually broadened absorption spectra and slightly down-shifted lowest unoccupied molecular orbital levels. The active layer based on terpolymer PF1-TS4-60 with a 60% ITIC unit presents more balanced hole and electron mobilities, higher photoluminescence quenching efficiency, and improved morphology compared to those based on PF1-TS4. In all-polymer solar cells (all-PSCs), PF1-TS4-60, matched with a wide band gap polymer donor PM6, achieved a similar open-circuit voltage (V-oc) of 0.99 V, a dramatically increased short-circuit current density (J(sc)) of 15.30 mA cm(-2), and fill factor (FF) of 61.4% compared to PF1-TS4 = 0.99 V, J(sc) = 11.21 mA cm(-2), and FF = 55.6%). As a result, the PF1-TS4-60-based all-PSCs achieved a PCE of 9.31%, which is similar to 50% higher than the PF1-TS4-based ones (6.17%). The results demonstrate a promising approach to develop high-performance nonconjugated terpolymer acceptors for efficient all-PSCs by means of ternary polymerization using two different A-D-A-structured fused-ring electron-deficient building blocks.
|
|
| 14. |
- Wang, Yufei, et al.
(författare)
-
Acidochromic organic photovoltaic integrated device
- 2023
-
Ingår i: Chemical Engineering Journal. - : Elsevier BV. - 1385-8947. ; 452
-
Tidskriftsartikel (refereegranskat)abstract
- Tremendous efforts have been devoted to boosting the power conversion efficiency (PCE) of organic solar cells (OSCs) via the introduction of cathode interlayers (CILs). However, CIL materials have limited diversity and the development of multifunctional devices is largely neglected. Herein, an acidochromic organic photovoltaic integrated device is firstly proposed by introducing an acid-sensitive stimulating-reaction organic molecule as both the CIL of OSCs and the sensor of monitoring environmental acidity. The oxazolidine unit of acidochromic molecule can form a ring-opening structure after acid treatment, resulting in the remarkable color change with the direct reflection of pH value of ecological environment. The additive-free PM6:Y6 OSCs using the acidochromic molecule as the CIL achieve an excellent PCE of above 15.29 %, which is 47 % higher than that of the control device. The PCE can even maintain above 92 % after treating CIL with various strong acids (pH = 1). Moreover, the color of acidified films and the degraded performance of acidified OSCs can be easily restored by alkaline treatment. The successful application of CIL in other highly efficient photovoltaic systems proves its good universality. This work triggers the promising application of acidochromic molecules in solar cells as CIL with the additional function of recognition of acid environment.
|
|
| 15. |
- Wu, Jingnan, et al.
(författare)
-
Carboxylate substituted pyrazine: A simple and low-cost building block for novel wide bandgap polymer donor enables 15.3% efficiency in organic solar cells
- 2021
-
Ingår i: Nano Energy. - : Elsevier BV. - 2211-2855. ; 82
-
Tidskriftsartikel (refereegranskat)abstract
- In addition to high power conversion efficiency (PCE) and good stability, the low-cost of photovoltaic materials is also very important for the practical application of organic solar cells (OSCs). Herein, we synthesized a carboxylate substituted pyrazine-based electron-deficient building block (DTCPz) with a simple structure and low synthetic cost, and then developed a novel wide bandgap polymer donor PFBCPZ. Due to the synergistic electron-withdrawing effects of the fluorination in donor unit (BDT-TF) and esterification and C=N double-bond in DTCPz unit, PFBCPZ shows a deeper HOMO level of −5.60 eV, a strong intermolecular π-π interaction, good crystallinity and stacking, and high hole-mobility of 2.11 × 10−3 cm2 V−1 s−1. Matched with a low bandgap acceptor IT-4F, excellent charge transfer, weak recombination, and small non-radiative energy loss in OSCs was achieved, resulting in an impressive fill factor of 0.785 and a high open-circuit voltage of 0.92 V. As a result, a PCE of up to 15.3% is obtained in OSCs, which is the highest value in the IT-4F-based binary OSCs so far and indicates that low-cost DTCPz with a simple structure is a promising building block to construct high-performance polymer donors for application in efficient OSCs.
|
|
| 16. |
- Xiao, Manjun, et al.
(författare)
-
Approaching 19% efficiency and stable binary polymer solar cells enabled by a solidification strategy of solvent additive
- 2023
-
Ingår i: Science in China Series B. - : SCIENCE PRESS. - 1674-7291 .- 1869-1870. ; 66, s. 1500-1510
-
Tidskriftsartikel (refereegranskat)abstract
- Additives play a crucial role in enhancing the photovoltaic performance of polymer solar cells (PSCs). However, the typical additives used to optimize blend morphology of PSCs are still high boiling-point solvents, while their trace residues may reduce device stability. Herein, an effective strategy of "solidification of solvent additive (SSA)" has been developed to convert additive from liquid to solid, by introducing a covalent bond into low-cost solvent diphenyl sulfide (DPS) to synthesize solid dibenzothiophene (DBT) in one-step, which achieves optimized morphology thus promoting efficiency and device stability. Owing to the fine planarity and volatilization of DBT, the DBT-processed films achieve ordered molecular crystallinity and suitable phase separation compared to the additive-free or DPS-treated ones. Importantly, the DBT-processed device also possesses improved light absorption, enhanced charge transport, and thus a champion efficiency of 11.9% is achieved in the PM6:Y6-based PSCs with an excellent additive component tolerance, reproducibility, and stability. Additionally, the DBT-processed PM6:L8-BO-based PSCs are further fabricated to study the universality of SSA strategy, offering an impressive efficiency approaching 19% as one of the highest values in binary PSCs. In conclusion, this article developed a promising strategy named SSA to boost efficiency and improve stability of PSCs.
|
|
| 17. |
- Yi, Fan, et al.
(författare)
-
Non-Fully Conjugated Dimerized Giant Acceptors with Different Alkyl-Linked Sites for Stable and 19.13 % Efficiency Organic Solar Cells
- 2024
-
Ingår i: Angewandte Chemie International Edition. - : WILEY-V C H VERLAG GMBH. - 1433-7851 .- 1521-3773.
-
Tidskriftsartikel (refereegranskat)abstract
- Achieving both high power conversion efficiency (PCE) and device stability is a major challenge for the practical development of organic solar cells (OSCs). Herein, three non-fully conjugated dimerized giant acceptors (named 2Y-sites, including wing-site-linked 2Y-wing, core-site-linked 2Y-core, and end-site-linked 2Y-end) are developed. They share the similar monomer precursors but have different alkyl-linked sites, offering the fine-tuned molecular absorption, packing, glass transition temperature, and carrier mobility. Among their binary active layers, D18/2Y-wing has better miscibility, leading to optimized morphology and more efficient charge transfer compared to D18/2Y-core and D18/2Y-end. Therefore, the D18/2Y-wing-based OSCs achieve a superior PCE of 17.73 %, attributed to enhanced photocurrent and fill factor. Furthermore, the D18/2Y-wing-based OSCs exhibit a balance of high PCE and improved stability, distinguishing them within the 2Y-sites. Building on the success of 2Y-wing in binary systems, we extend its application to ternary OSCs by pairing it with the near-infrared absorbing D18/BS3TSe-4F host. Thanks to the complementary absorption within 300-970 nm and further optimized morphology, ternary OSCs obtain a higher PCE of 19.13 %, setting a new efficiency benchmark for the dimer-derived OSCs. This approach of alkyl-linked site engineering for constructing dimerized giant acceptors presents a promising pathway to improve both PCE and stability of OSCs. Three new non-fully conjugated dimerized giant acceptors with different alkyl-linked sites are developed. Among them, wing-sited 2Y-wing has fine-tuned packing and better miscibility with donor, allowing to 19.13 % efficiency (which is the highest value among the devices with giant acceptors) and highly stable organic solar cells. image
|
|
