1. |
- Elmlund, Louise, 1981-, et al.
(author)
-
A Phage Display Screening Derived Peptide with Affinity for the Adeninyl Moiety
- 2014
-
In: Biosensors. - : MDPI. - 2079-6374. ; 4:2, s. 137-149
-
Journal article (peer-reviewed)abstract
- Phage display screening of a surface-immobilized adenine derivative led to the identification of a heptameric peptide with selectivity for adenine as demonstrated through quartz crystal microbalance (QCM) studies. The peptide demonstrated a concentration dependent affinity for an adeninyl moiety decorated surface (KD of 968 ± 53.3 μM), which highlights the power of piezoelectric sensing in the study of weak interactions.
|
|
2. |
- Baumgartner, D, et al.
(author)
-
OralDisk: A Chair-Side Compatible Molecular Platform Using Whole Saliva for Monitoring Oral Health at the Dental Practice
- 2021
-
In: Biosensors. - : MDPI AG. - 2079-6374. ; 11:11
-
Journal article (peer-reviewed)abstract
- Periodontitis and dental caries are two major bacterially induced, non-communicable diseases that cause the deterioration of oral health, with implications in patients’ general health. Early, precise diagnosis and personalized monitoring are essential for the efficient prevention and management of these diseases. Here, we present a disk-shaped microfluidic platform (OralDisk) compatible with chair-side use that enables analysis of non-invasively collected whole saliva samples and molecular-based detection of ten bacteria: seven periodontitis-associated (Aggregatibacter actinomycetemcomitans, Campylobacter rectus, Fusobacterium nucleatum, Prevotella intermedia, Porphyromonas gingivalis, Tannerella forsythia, Treponema denticola) and three caries-associated (oral Lactobacilli, Streptococcus mutans, Streptococcus sobrinus). Each OralDisk test required 400 µL of homogenized whole saliva. The automated workflow included bacterial DNA extraction, purification and hydrolysis probe real-time PCR detection of the target pathogens. All reagents were pre-stored within the disk and sample-to-answer processing took < 3 h using a compact, customized processing device. A technical feasibility study (25 OralDisks) was conducted using samples from healthy, periodontitis and caries patients. The comparison of the OralDisk with a lab-based reference method revealed a ~90% agreement amongst targets detected as positive and negative. This shows the OralDisk’s potential and suitability for inclusion in larger prospective implementation studies in dental care settings.
|
|
3. |
- Campos-Beltran, Diana, et al.
(author)
-
Amperometric Self-Referencing Ceramic Based Microelectrode Arrays for D-Serine Detection
- 2018
-
In: Biosensors. - : MDPI. - 2079-6374. ; 8:1
-
Journal article (peer-reviewed)abstract
- D-serine is the major D-amino acid in the mammalian central nervous system. As the dominant co-agonist of the endogenous synaptic NMDA receptor, D-serine plays a role in synaptic plasticity, learning, and memory. Alterations in D-serine are linked to neuropsychiatric disorders including schizophrenia. Thus, it is of increasing interest to monitor the concentration of D-serine in vivo as a relevant player in dynamic neuron-glia network activity. Here we present a procedure for amperometric detection of D-serine with self-referencing ceramic-based microelectrode arrays (MEAs) coated with D-amino acid oxidase from the yeast Rhodotorula gracilis (RgDAAO). We demonstrate in vitro D-serine recordings with a mean sensitivity of 8.61 +/- 0.83 pA/mu M to D-serine, a limit of detection (LOD) of 0.17 +/- 0.01 mu M, and a selectivity ratio of 80:1 or greater for D-serine over ascorbic acid (mean +/- SEM; n = 12) that can be used for freely moving studies.
|
|
4. |
- Carrasco, Sergio
(author)
-
Metal-Organic Frameworks for the Development of Biosensors : A Current Overview
- 2018
-
In: Biosensors. - : MDPI AG. - 2079-6374. ; 8:4
-
Research review (peer-reviewed)abstract
- This review focuses on the fabrication of biosensors using metal-organic frameworks (MOFs) as recognition and/or transducer elements. A brief introduction discussing the importance of the development of new biosensor schemes is presented, describing these coordination polymers, their properties, applications, and the main advantages and drawbacks for the final goal. The increasing number of publications regarding the characteristics of these materials and the new micro- and nanofabrication techniques allowing the preparation of more accurate, robust, and sensitive biosensors are also discussed. This work aims to offer a new perspective from the point of view of materials science compared to other reviews focusing on the transduction mechanism or the nature of the analyte. A few examples are discussed depending on the starting materials, the integration of the MOF as a part of the biosensor and, in a deep detail, the fabrication procedure.
|
|
5. |
- Diouani, Mohamed Fethi, et al.
(author)
-
Casein-Conjugated Gold Nanoparticles for Amperometric Detection of Leishmania infantum
- 2019
-
In: Biosensors. - : MDPI AG. - 2079-6374. ; 9:2
-
Journal article (peer-reviewed)abstract
- Sensitive and reliable approaches targeting the detection of Leishmania are critical for effective early diagnosis and treatment of leishmaniasis. In this frame, this paper describes a rapid quantification assay to detect Leishmania parasites based on the combination of the electrocatalytic ability of gold nanoparticles (AuNPs) to act as a catalyst for the hydrogen formation reaction along with the specificity of the interaction between casein and the major surface protease of the Leishmania parasite, GP63. First, pure and casein-modified AuNPs were prepared and characterized by scanning electron microscopy and ultraviolet-visible spectroscopy. Then, casein-conjugated AuNPs were incubated with Leishsmania parasites in solution; the formed complex was collected by centrifugation, treated by acidic solution, and the pelleted AuNPs were placed on screen-printed carbon electrodes (SPCEs) and chronoamperometric measurements were carried out. Our results suggest that it is possible to detect Leishmania parasites, with a limit less than 1 parasite/mL. A linear response over a wide concentration interval, ranging from 2 x 10(-2) to 2 x 10(5) parasites/mL, was achieved. Additionally, a pretreatment of Leishmania parasites with Amphotericin B, diminished their interaction with casein. This findings and methodology are very useful for drug efficacy assessment.
|
|
6. |
- Hernandez, Cesar A, et al.
(author)
-
Fully Automated Microsystem for Unmediated Electrochemical Characterization, Visualization and Monitoring of Bacteria on Solid Media; E. coli K-12 : A Case Study.
- 2019
-
In: Biosensors. - : MDPI AG. - 2079-6374. ; 9:4
-
Journal article (peer-reviewed)abstract
- In this paper, we present a non-fluidic microsystem for the simultaneous visualization and electrochemical evaluation of confined, growing bacteria on solid media. Using a completely automated platform, real-time monitoring of bacterial and image-based computer characterization of growth were performed. Electrochemical tests, using Escherichia coli K-12 as the model microorganism, revealed the development of a faradaic process at the bacteria-microelectrode interface inside the microsystem, as implied by cyclic voltammetry and electrochemical impedance spectrometry measurements. The electrochemical information was used to determine the moment in which bacteria colonized the electrode-enabled area of the microsystem. This microsystem shows potential advantages for long-term electrochemical monitoring of the extracellular environment of cell culture and has been designed using readily available technologies that can be easily integrated in routine protocols. Complementarily, these methods can help elucidate fundamental questions of the electron transfer of bacterial cultures and are potentially feasible to be integrated into current characterization techniques.
|
|
7. |
- Hernandez, Frank J, et al.
(author)
-
Graphene and other nanomaterial-based electrochemical aptasensors.
- 2012
-
In: Biosensors. - : MDPI AG. - 2079-6374. ; 2:1, s. 1-14
-
Journal article (peer-reviewed)abstract
- Electrochemical aptasensors, which are based on the specificity of aptamer-target recognition, with electrochemical transduction for analytical purposes have received particular attention due to their high sensitivity and selectivity, simple instrumentation, as well as low production cost. Aptamers are functional nucleic acids with specific and high affinity to their targets, similar to antibodies. However, they are completely selected in vitro in contrast to antibodies. Due to their stability, easy chemical modifications and proneness to nanostructured device construction, aptamer-based sensors have been incorporated in a variety of applications including electrochemical sensing devices. In recent years, the performance of aptasensors has been augmented by incorporating novel nanomaterials in the preparation of better electrochemical sensors. In this review, we summarize the recent trends in the use of nanomaterials for developing electrochemical aptasensors.
|
|
8. |
- Idil, Neslihan, et al.
(author)
-
Whole cell recognition of staphylococcus aureus using biomimetic SPR sensors
- 2021
-
In: Biosensors. - : MDPI AG. - 2079-6374. ; 11:5
-
Journal article (peer-reviewed)abstract
- Over the past few decades, a significant increase in multi-drug-resistant pathogenic microorganisms has been of great concern and directed the research subject to the challenges that the distribution of resistance genes represent. Globally, high levels of multi-drug resistance represent a significant health threat and there is a growing requirement of rapid, accurate, real-time detection which plays a key role in tracking of measures for the infections caused by these bacterial strains. It is also important to reduce transfer of resistance genes to new organisms. The, World Health Organization has informed that millions of deaths have been reported each year recently. To detect the resistant organisms traditional detection approaches face limitations, therefore, newly developed technologies are needed that are suitable to be used in large-scale applications. In the present study, the aim was to design a surface plasmon resonance (SPR) sensor with micro-contact imprinted sensor chips for the detection of Staphylococcus aureus. Whole cell imprinting was performed by N-methacryloyl-L-histidine methyl ester (MAH) under UV polymerization. Sensing experiments were done within a concentration range of 1.0 × 102–2.0 × 105 CFU/mL. The recognition of S. aureus was accomplished by the involvement of microcontact imprinting and optical sensor technology with a detection limit of 1.5 × 103 CFU/mL. Selectivity of the generated sensor was evaluated through injections of competing bacterial strains. The responses for the different strains were compared to that of S. aureus. Besides, real experiments were performed with milk samples spiked with S. aureus and it was demonstrated that the prepared sensor platform was applicable for real samples.
|
|
9. |
- Lohcharoenkal, Warangkana, et al.
(author)
-
Advances in Nanotechnology-Based Biosensing of Immunoregulatory Cytokines
- 2021
-
In: Biosensors. - : MDPI AG. - 0956-5663 .- 2079-6374. ; 11:10
-
Research review (peer-reviewed)abstract
- Cytokines are a large group of small proteins secreted by immune and non-immune cells in response to external stimuli. Much attention has been given to the application of cytokines’ detection in early disease diagnosis/monitoring and therapeutic response assessment. To date, a wide range of assays are available for cytokines detection. However, in specific applications, multiplexed or continuous measurements of cytokines with wearable biosensing devices are highly desirable. For such efforts, various nanomaterials have been extensively investigated due to their extraordinary properties, such as high surface area and controllable particle size and shape, which leads to their tunable optical emission, electrical, and magnetic properties. Different types of nanomaterials such as noble metal, metal oxide, and carbon nanoparticles have been explored for various biosensing applications. Advances in nanomaterial synthesis and device development have led to significant progress in pushing the limit of cytokine detection. This article reviews currently used methods for cytokines detection and new nanotechnology-based biosensors for ultrasensitive cytokine detection
|
|
10. |
- Martín-Yerga, Daniel
(author)
-
Electrochemical Detection and Characterization of Nanoparticles with Printed Devices
- 2019
-
In: Biosensors. - : MDPI AG. - 2079-6374. ; 9:2
-
Research review (peer-reviewed)abstract
- Innovative methods to achieve the user-friendly, quick, and highly sensitive detection of nanomaterials are urgently needed. Nanomaterials have increased importance in commercial products, and there are concerns about the potential risk that they entail for the environment. In addition, detection of nanomaterials can be a highly valuable tool in many applications, such as biosensing. Electrochemical methods using disposable, low-cost, printed electrodes provide excellent analytical performance for the detection of a wide set of nanomaterials. In this review, the foundations and latest advances of several electrochemical strategies for the detection of nanoparticles using cost-effective printed devices are introduced. These strategies will equip the experimentalist with an extensive toolbox for the detection of nanoparticles of different chemical nature and possible applications ranging from quality control to environmental analysis and biosensing.
|
|
11. |
- Paulmurugan, K, et al.
(author)
-
Brain-Computer Interfacing Using Functional Near-Infrared Spectroscopy (fNIRS)
- 2021
-
In: Biosensors. - : MDPI AG. - 2079-6374. ; 11:10
-
Journal article (peer-reviewed)abstract
- Functional Near-Infrared Spectroscopy (fNIRS) is a wearable optical spectroscopy system originally developed for continuous and non-invasive monitoring of brain function by measuring blood oxygen concentration. Recent advancements in brain–computer interfacing allow us to control the neuron function of the brain by combining it with fNIRS to regulate cognitive function. In this review manuscript, we provide information regarding current advancement in fNIRS and how it provides advantages in developing brain–computer interfacing to enable neuron function. We also briefly discuss about how we can use this technology for further applications.
|
|
12. |
- Peng, Tingting, et al.
(author)
-
The Spectroscopic Properties and Microscopic Imaging of Thulium-Doped Upconversion Nanoparticles Excited at Different NIR-II Light
- 2021
-
In: Biosensors. - : MDPI AG. - 2079-6374. ; 11:5
-
Journal article (peer-reviewed)abstract
- Lanthanide-doped upconversion nanoparticles (UCNPs) are promising bioimaging nanoprobes due to their excellent photostability. As one of the most commonly used lanthanide activators, Tm3+ ions have perfect ladder-type electron configuration and can be directly excited by bio-friendly near-infrared-II (NIR-II) wavelengths. Here, the emission characteristics of Tm3+-doped nanoparticles under laser excitations of different near-infrared-II wavelengths were systematically investigated. The 1064 nm, 1150 nm, and 1208 nm lasers are proposed to be three excitation strategies with different response spectra of Tm3+ ions. In particular, we found that 1150 nm laser excitation enables intense three-photon 475 nm emission, which is nearly 100 times stronger than that excited by 1064 nm excitation. We further optimized the luminescence brightness after investigating the luminescence quenching mechanism of bare NaYF4: Tm (1.75%) core. After growing an inert shell, a ten-fold increase of emission intensity was achieved. Combining the advantages of NIR-II wavelength and the higher-order nonlinear excitation, a promising facile excitation strategy was developed for the application of thulium-doped upconversion nanoparticles in nanoparticles imaging and cancer cell microscopic imaging.
|
|
13. |
- Pereira da Silva Neves, Marta Maria, et al.
(author)
-
Advanced Nanoscale Approaches to Single-(Bio)entity Sensing and Imaging
- 2018
-
In: Biosensors. - : MDPI. - 2079-6374. ; 8:4
-
Research review (peer-reviewed)abstract
- Individual (bio)chemical entities could show a very heterogeneous behaviour under the same conditions that could be relevant in many biological processes of significance in the life sciences. Conventional detection approaches are only able to detect the average response of an ensemble of entities and assume that all entities are identical. From this perspective, important information about the heterogeneities or rare (stochastic) events happening in individual entities would remain unseen. Some nanoscale tools present interesting physicochemical properties that enable the possibility to detect systems at the single-entity level, acquiring richer information than conventional methods. In this review, we introduce the foundations and the latest advances of several nanoscale approaches to sensing and imaging individual (bio)entities using nanoprobes, nanopores, nanoimpacts, nanoplasmonics and nanomachines. Several (bio)entities such as cells, proteins, nucleic acids, vesicles and viruses are specifically considered. These nanoscale approaches provide a wide and complete toolbox for the study of many biological systems at the single-entity level.
|
|
14. |
- Razmi, Nasrin, et al.
(author)
-
Recent Progress on the Electrochemical Biosensing of Escherichia coli O157:H7: Material and Methods Overview
- 2020
-
In: Biosensors. - : MDPI. - 2079-6374. ; 10:5
-
Research review (peer-reviewed)abstract
- Escherichia coliO157:H7 (E. coliO157:H7) is a pathogenic strain ofEscherichia coliwhich has issued as a public health threat because of fatal contamination of food and water. Therefore, accurate detection of pathogenicE. coliis important in environmental and food quality monitoring. In spite of their advantages and high acceptance, culture-based methods, enzyme-linked immunosorbent assays (ELISAs), polymerase chain reaction (PCR), flow cytometry, ATP bioluminescence, and solid-phase cytometry have various drawbacks, including being time-consuming, requiring trained technicians and/or specific equipment, and producing biological waste. Therefore, there is necessity for affordable, rapid, and simple approaches. Electrochemical biosensors have shown great promise for rapid food- and water-borne pathogen detection. Over the last decade, various attempts have been made to develop techniques for the rapid quantification ofE. coliO157:H7. This review covers the importance ofE. coliO157:H7 and recent progress (from 2015 to 2020) in the development of the sensitivity and selectivity of electrochemical sensors developed forE. coliO157:H7 using different nanomaterials, labels, and electrochemical transducers.
|
|
15. |
- Sánchez Martín, Darío, et al.
(author)
-
Evaluating the performance of a magnetic nanoparticle-based detection method using circle-to-circle amplification
- 2021
-
In: Biosensors. - : MDPI. - 2079-6374. ; 11:6
-
Journal article (peer-reviewed)abstract
- This work explores several issues of importance for the development of a diagnostic method based on circle-to-circle amplification (C2CA) and oligonucleotide-functionalized magnetic nanoparticles. Firstly, the performance of the detection method was evaluated in terms of sensitivity and speed. Synthetic target sequences for Newcastle disease virus and Salmonella were used as model sequences. The sensitivity of the C2CA assay resulted in detection of 1 amol of starting DNA target with a total amplification time of 40 min for both target sequences. Secondly, the functionalization of the nanoparticles was evaluated in terms of robustness and stability. The functionalization was shown to be very robust, and the stability test showed that 92% of the oligos were still attached on the particle surface after three months of storage at 4 degrees C. Altogether, the results obtained in this study provide a strong foundation for the development of a quick and sensitive diagnostic assay.
|
|
16. |
- Schmidheini, Lukas, et al.
(author)
-
Self-Assembly of Nanodiamonds and Plasmonic Nanoparticles for Nanoscopy
- 2022
-
In: Biosensors. - : MDPI AG. - 2079-6374. ; 12:3
-
Journal article (peer-reviewed)abstract
- Nanodiamonds have emerged as promising agents for sensing and imaging due to their exceptional photostability and sensitivity to the local nanoscale environment. Here, we introduce a hybrid system composed of a nanodiamond containing nitrogen-vacancy center that is paired to a gold nanoparticle via DNA hybridization. Using multiphoton optical studies, we demonstrate that the harmonic mode emission generated in gold nanoparticles induces a coupled fluorescence emission in nanodiamonds. We show that the flickering of harmonic emission in gold nanoparticles directly influences the nanodiamonds' emissions, resulting in stochastic blinking. By utilizing the stochastic emission fluctuations, we present a proof-of-principle experiment to demonstrate the potential application of the hybrid system for super-resolution microscopy. The introduced system may find applications in intracellular biosensing and bioimaging due to the DNA-based coupling mechanism and also the attractive characteristics of harmonic generation, such as low power, low background and tissue transparency.
|
|
17. |
- Sepehri, Sobhan, 1986, et al.
(author)
-
Characterization of Binding of Magnetic Nanoparticles to Rolling Circle Amplification Products by Turn-On Magnetic Assay
- 2019
-
In: Biosensors-Basel. - : MDPI AG. ; 9:3
-
Journal article (peer-reviewed)abstract
- The specific binding of oligonucleotide-tagged 100 nm magnetic nanoparticles (MNPs) to rolling circle products (RCPs) is investigated using our newly developed differential homogenous magnetic assay (DHMA). The DHMA measures ac magnetic susceptibility from a test and a control samples simultaneously and eliminates magnetic background signal. Therefore, the DHMA can reveal details of binding kinetics of magnetic nanoparticles at very low concentrations of RCPs. From the analysis of the imaginary part of the DHMA signal, we find that smaller MNPs in the particle ensemble bind first to the RCPs. When the RCP concentration increases, we observe the formation of agglomerates, which leads to lower number of MNPs per RCP at higher concentrations of RCPs. The results thus indicate that a full frequency range of ac susceptibility observation is necessary to detect low concentrations of target RCPs and a long amplification time is not required as it does not significantly increase the number of MNPs per RCP. The findings are critical for understanding the underlying microscopic binding process for improving the assay performance. They furthermore suggest DHMA is a powerful technique for dynamically characterizing the binding interactions between MNPs and biomolecules in fluid volumes.
|
|
18. |
- Sorsa, T, et al.
(author)
-
Host-Modulation Therapy and Chair-Side Diagnostics in the Treatment of Peri-Implantitis
- 2020
-
In: Biosensors. - : MDPI AG. - 2079-6374. ; 10:5
-
Journal article (peer-reviewed)abstract
- Previous studies report periodontitis and peri-implantitis being able to induce systemic low-grade inflammation, which is known to be associated with increased risk for some systemic medical disease such as cardiovascular disease. In this regard, recent studies have shown that host modulation therapy (HMT) together with traditional mechanical and surgical treatment not only cease the progression of periodontitis but also reduce the systemic collagenolytic biomarkers in both oral fluids and circulation. This suggests that the corresponding adjunctive HMT-medication could be effective in the prevention and treatment of dental peri-implantitis, as well. Furthermore, low-cost, safe, and practical oral fluid active matrix metalloproteinase-8 (aMMP-8) lateral-flow immunotests have been proposed as point-of-care/chair-side diagnostic tools to detect peri-implantitis and periodontitis, and to monitor their effective resolutions, while using various therapeutic strategies, including host modulation. This study reports the potential benefits of HMT-medication in the prevention and treatment of dental peri-implantitis among five patients (four of five were current/ex-smokers). In addition, the aMMP-8 point-of-care test diagnosed 20 peri-implantitis and 20 healthy controls correctly. In conclusion, this study and previous studies support the potential effectiveness of HMT-medication(s) and point-of-care/chair-side technologies in the treatment and diagnostics/monitoring of peri-implantitis. However, more studies are needed to further confirm this.
|
|
19. |
- Su, Binbin, et al.
(author)
-
Gait Phase Recognition Using Deep Convolutional Neural Network with Inertial Measurement Units
- 2020
-
In: Biosensors. - : MDPI AG. - 2079-6374. ; 10:9, s. 109-109
-
Journal article (peer-reviewed)abstract
- Gait phase recognition is of great importance in the development of assistance-as-needed robotic devices, such as exoskeletons. In order for a powered exoskeleton with phase-based control to determine and provide proper assistance to the wearer during gait, the user’s current gait phase must first be identified accurately. Gait phase recognition can potentially be achieved through input from wearable sensors. Deep convolutional neural networks (DCNN) is a machine learning approach that is widely used in image recognition. User kinematics, measured from inertial measurement unit(IMU) output, can be considered as an ‘image’ since it exhibits some local ‘spatial’ pattern when the sensor data is arranged in sequence. We propose a specialized DCNN to distinguish five phases in a gait cycle, based on IMU data and classified with foot switch information. The DCNN showed approximately 97% accuracy during an offline evaluation of gait phase recognition. Accuracy was highest in the swing phase and lowest in terminal stance.
|
|
20. |
- Suriyanarayanan, Subramanian, et al.
(author)
-
Hierarchical Thin Film Architectures for Enhanced Sensor Performance : Liquid Crystal-Mediated Electrochemical Synthesis of Nanostructured Imprinted Polymer Films for the Selective Recognition of Bupivacaine
- 2014
-
In: Biosensors. - : MDPI. - 2079-6374. ; 4:2, s. 90-110
-
Journal article (peer-reviewed)abstract
- Nanostructured bupivacaine-selective molecularly imprinted 3-aminophenylboronic acid-p-phenylenediamine co-polymer (MIP) films have been prepared on gold-coated quartz (Au/quartz) resonators by electrochemical synthesis under cyclic voltammetric conditions in a liquid crystalline (LC) medium (triton X-100/water). Films prepared in water and in the absence of template were used for control studies. Infrared spectroscopic studies demonstrated comparable chemical compositions for LC and control polymer films. SEM studies revealed that the topologies of the molecularly imprinted polymer films prepared in the LC medium (LC-MIP) exhibit discernible 40 nm thick nano-fiber structures, quite unlike the polymers prepared in the absence of the LC-phase. The sensitivity of the LC-MIP in a quartz crystal microbalance (QCM) sensor platform was 67.6 ± 4.9 Hz/mM under flow injection analysis (FIA) conditions, which was ≈250% higher than for the sensor prepared using the aqueous medium. Detection was possible at 100 nM (30 ng/mL), and discrimination of bupivacaine from closely related structural analogs was readily achieved as reflected in the corresponding stability constants of the MIP-analyte complexes. The facile fabrication and significant enhancement in sensor sensitivity together highlight the potential of this LC-based imprinting strategy for fabrication of polymeric materials with hierarchical architectures, in particular for use in surface-dependent application areas, e.g., biomaterials or sensing.
|
|
21. |
- Yunos, Muhammad Farhan Affendi Mohamad, et al.
(author)
-
RF Remote Blood Glucose Sensor and a Microfluidic Vascular Phantom for Sensor Validation
- 2021
-
In: Biosensors. - : MDPI. - 2079-6374. ; 11:12
-
Journal article (peer-reviewed)abstract
- Diabetes has become a major health problem in society. Invasive glucometers, although precise, only provide discrete measurements at specific times and are unsuitable for long-term monitoring due to the injuries caused on skin and the prohibitive cost of disposables. Remote, continuous, self-monitoring of blood sugar levels allows for active and better management of diabetics. In this work, we present a radio frequency (RF) sensor based on a stepped impedance resonator for remote blood glucose monitoring. When placed on top of a human hand, this RF interdigital sensor allows detection of variation in blood sugar levels by monitoring the changes in the dielectric constant of the material underneath. The designed stepped impedance resonator operates at 3.528 GHz with a Q factor of 1455. A microfluidic device structure that imitates the blood veins in the human hand was fabricated in PDMS to validate that the sensor can measure changes in glucose concentrations. To test the RF sensor, glucose solutions with concentrations ranging from 0 to 240 mg/dL were injected into the fluidic channels and placed underneath the RF sensor. The shifts in the resonance frequencies of the RF sensor were measured using a network analyzer via its S-11 parameters. Based on the change in resonance frequencies, the sensitivity of the biosensor was found to be 264.2 kHz/mg center dot dL(-1) and its LOD was calculated to be 29.89 mg/dL.
|
|
22. |
- Falk, Magnus, et al.
(author)
-
Electronic Tongue for Direct Assessment of SARS-CoV-2-Free and Infected Human Saliva-A Feasibility Study
- 2023
-
In: Biosensors. - : MDPI. - 2079-6374. ; 13:7
-
Journal article (peer-reviewed)abstract
- An electronic tongue is a powerful analytical instrument based on an array of non-selective chemical sensors with a partial specificity for data gathering and advanced pattern recognition methods for data analysis. Connecting electronic tongues with electrochemical techniques for data collection has led to various applications, mostly within sensing for food quality and environmental monitoring, but also in biomedical research for the analyses of different bioanalytes in human physiological fluids. In this paper, an electronic tongue consisting of six electrodes (viz., gold, platinum, palladium, titanium, iridium, and glassy carbon) was designed and tested in authentic (undiluted, unpretreated) human saliva samples from eight volunteers, collected before and during the COVID-19 pandemic. Investigations of 11 samples using differential pulse voltammetry and a principal component analysis allowed us to distinguish between SARS-CoV-2-free and infected authentic human saliva. This work, as a proof-of-principle demonstration, provides a new perspective for the use of electronic tongues in the field of enzyme-free electrochemical biosensing, highlighting their potential for future applications in non-invasive biomedical analyses.
|
|
23. |
- Fast, L, et al.
(author)
-
Fluorescence-Based Measurements of Membrane-Bound Angiotensin Converting Enzyme 2 Activity Using Xenopus Laevis Oocytes
- 2022
-
In: Biosensors. - : MDPI AG. - 2079-6374. ; 12:8
-
Journal article (peer-reviewed)abstract
- Functional investigations of enzymes involving cellular expression systems are important for pharmacological studies. The precise control of expression is challenging in transiently transfected mammalian cell lines. Here, we explored the ability of Xenopus laevis oocytes to express a membrane-bound enzyme for functional characterization using standard 96-well plates and a fluorescence-based plate reader assay. We microinjected oocytes with cRNA encoding the angiotensin converting enzyme 2 (ACE2) and measured the enzymatic activity in single oocytes using a commercial fluorescence-based assay. The injected oocytes showed up to a 50-fold increase in fluorescence compared to uninjected oocytes. This fluorescence intensity was dose-dependent on the amount of ACE2 cRNA. These results suggest that Xenopus oocytes can be used for the functional evaluation of membrane-bound enzymes, decreasing the experimental workload.
|
|
24. |
- Figueiredo, Carina, et al.
(author)
-
Effect of Protection Polymer Coatings on the Performance of an Amperometric Galactose Biosensor in Human Plasma
- 2024
-
In: Biosensors. - 2079-6374. ; 14:4
-
Journal article (peer-reviewed)abstract
- Galactose monitoring in individuals allows the prevention of harsh health conditions related to hereditary metabolic diseases like galactosemia. Current methods of galactose detection need development to obtain cheaper, more reliable, and more specific sensors. Enzyme-containing amperometric sensors based on galactose oxidase activity are a promising approach, which can be enhanced by means of their inclusion in a redox polymer coating. This strategy simultaneously allows the immobilization of the biocatalyst to the electroactive surface and hosts the electron shuttling units. An additional deposition of capping polymers prevents external interferences like ascorbic or uric acid as well as biofouling when measuring in physiological fuels. This work studies the protection effect of poly(2-methacryloyloxyethyl phosphorylcholine-co-glycidyl methacrylate (MPC) and polyvinylimidazole-polysulfostyrene (P(VI-SS)) when incorporated in the biosensor design for the detection of galactose in human plasma.
|
|
25. |
- Hanze, Martin, et al.
(author)
-
Toward Continuous Molecular Testing Using Gold-Coated Threads as Multi-Target Electrochemical Biosensors
- 2023
-
In: Biosensors. - : MDPI AG. - 2079-6374. ; 13:9
-
Journal article (peer-reviewed)abstract
- Analytical systems based on isothermal nucleic acid amplification tests (NAATs) paired with electroanalytical detection enable cost-effective, sensitive, and specific digital pathogen detection for various in situ applications such as point-of-care medical diagnostics, food safety monitoring, and environmental surveillance. Self-assembled monolayers (SAMs) on gold surfaces are reliable platforms for electroanalytical DNA biosensors. However, the lack of automation and scalability often limits traditional chip-based systems. To address these challenges, we propose a continuous thread-based device that enables multiple electrochemical readings on a functionalized working electrode Au thread with a single connection point. We demonstrate the possibility of rolling the thread on a spool, which enables easy manipulation in a roll-to-roll architecture for high-throughput applications. As a proof of concept, we have demonstrated the detection of recombinase polymerase amplification (RPA) isothermally amplified DNA from the two toxic microalgae species Ostreopsis cf. ovata and Ostreopsis cf. siamensis by performing a sandwich hybridization assay (SHA) with electrochemical readout.
|
|
26. |
|
|
27. |
- Johannsen, B, et al.
(author)
-
ImmunoDisk-A Fully Automated Bead-Based Immunoassay Cartridge with All Reagents Pre-Stored
- 2022
-
In: Biosensors. - : MDPI AG. - 2079-6374. ; 12:6
-
Journal article (peer-reviewed)abstract
- In this paper, we present the ImmunoDisk, a fully automated sample-to-answer centrifugal microfluidic cartridge, integrating a heterogeneous, wash-free, magnetic- and fluorescent bead-based immunoassay (bound-free phase detection immunoassay/BFPD-IA). The BFPD-IA allows the implementation of a simple fluidic structure, where the assay incubation, bead separation and detection are performed in the same chamber. The system was characterized using a C-reactive protein (CRP) competitive immunoassay. A parametric investigation on air drying of protein-coupled beads for pre-storage at room temperature is presented. The key parameters were buffer composition, drying temperature and duration. A protocol for drying two different types of protein-coupled beads with the same temperature and duration using different drying buffers is presented. The sample-to-answer workflow was demonstrated measuring CRP in 5 µL of human serum, without prior dilution, utilizing only one incubation step, in 20 min turnaround time, in the clinically relevant concentration range of 15–115 mg/L. A reproducibility assessment over three disk batches revealed an average signal coefficient of variation (CV) of 5.8 ± 1.3%. A CRP certified reference material was used for method verification with a concentration CV of 8.6%. Our results encourage future testing of the CRP-ImmunoDisk in clinical studies and its point-of-care implementation in many diagnostic applications.
|
|
28. |
- Khati, Vamakshi, et al.
(author)
-
3D Bioprinting of Multi-Material Decellularized Liver Matrix Hydrogel at Physiological Temperatures
- 2022
-
In: Biosensors. - : MDPI AG. - 2079-6374. ; 12:7
-
Journal article (peer-reviewed)abstract
- Bioprinting is an acclaimed technique that allows the scaling of 3D architectures in an organized pattern but suffers from a scarcity of appropriate bioinks. Decellularized extracellular matrix (dECM) from xenogeneic species has garnered support as a biomaterial to promote tissue-specific regeneration and repair. The prospect of developing dECM-based 3D artificial tissue is impeded by its inherent low mechanical properties. In recent years, 3D bioprinting of dECM-based bioinks modified with additional scaffolds has advanced the development of load-bearing constructs. However, previous attempts using dECM were limited to low-temperature bioprinting, which is not favorable for a longer print duration with cells. Here, we report the development of a multi-material decellularized liver matrix (dLM) bioink reinforced with gelatin and polyethylene glycol to improve rheology, extrudability, and mechanical stability. This shear-thinning bioink facilitated extrusion-based bioprinting at 37 degrees C with HepG2 cells into a 3D grid structure with a further enhancement for long-term applications by enzymatic crosslinking with mushroom tyrosinase. The heavily crosslinked structure showed a 16-fold increase in viscosity (2.73 Pa s(-1)) and a 32-fold increase in storage modulus from the non-crosslinked dLM while retaining high cell viability (85-93%) and liver-specific functions. Our results show that the cytocompatible crosslinking of dLM bioink at physiological temperatures has promising applications for extended 3D-printing procedures.
|
|
29. |
- Kongkaew, Supatinee, et al.
(author)
-
Craft-and-Stick Xurographic Manufacturing of Integrated Microfluidic Electrochemical Sensing Platform
- 2023
-
In: Biosensors. - : MDPI. - 2079-6374. ; 13:4
-
Journal article (peer-reviewed)abstract
- An innovative modular approach for facile design and construction of flexible microfluidic biosensor platforms based on a dry manufacturing "craft-and-stick" approach is developed. The design and fabrication of the flexible graphene paper electrode (GPE) unit and polyethylene tetraphthalate sheet (PET)6/adhesive fluidic unit are completed by an economic and generic xurographic craft approach. The GPE widths and the microfluidic channels can be constructed down to 300 mu m and 200 mu m, respectively. Both units were assembled by simple double-sided adhesive tapes into a microfluidic integrated GPE (MF-iGPE) that are flexible, thin (<0.5 mm), and lightweight (0.4 g). We further functionalized the iGPE with Prussian blue and glucose oxidase for the fabrication of MF-iGPE glucose biosensors. With a closed-channel PET fluidic pattern, the MF-iGPE glucose biosensors were packaged and sealed to protect the integrated device from moisture for storage and could easily open with scissors for sample loading. Our glucose biosensors showed 2 linear dynamic regions of 0.05-1.0 and 1.0-5.5 mmol L-1 glucose. The MF-iGPE showed good reproducibility for glucose detection (RSD < 6.1%, n = 6) and required only 10 mu L of the analyte. This modular craft-and-stick manufacturing approach could potentially further develop along the concept of paper-crafted model assembly kits suitable for low-resource laboratories or classroom settings.
|
|
30. |
- Lavogina, D, et al.
(author)
-
Revisiting the Resazurin-Based Sensing of Cellular Viability: Widening the Application Horizon
- 2022
-
In: Biosensors. - : MDPI AG. - 2079-6374. ; 12:4
-
Journal article (peer-reviewed)abstract
- Since 1991, the NAD(P)H-aided conversion of resazurin to fluorescent resorufin has been widely used to measure viability based on the metabolic activity in mammalian cell culture and primary cells. However, different research groups have used divergent assay protocols, scarcely reporting the systematic optimization of the assay. Here, we perform extensive studies to fine-tune the experimental protocols utilizing resazurin-based viability sensing. Specifically, we focus on (A) optimization of the assay dynamic range in individual cell lines for the correct measurement of cytostatic and cytotoxic properties of the compounds; (B) dependence of the dynamic range on the physical quantity detected (fluorescence intensity versus change of absorbance spectrum); (C) calibration of the assay for the correct interpretation of data measured in hypoxic conditions; and (D) possibilities for combining the resazurin assay with other methods including measurement of necrosis and apoptosis. We also demonstrate the enhanced precision and flexibility of the resazurin-based assay regarding the readout format and kinetic measurement mode as compared to the widely used analogous assay which utilizes tetrazolium dye MTT. The discussed assay optimization guidelines provide useful instructions for the beginners in the field and for the experienced scientists exploring new ways for measurement of cellular viability using resazurin.
|
|
31. |
- Mangrio, Sanjha, et al.
(author)
-
Advanced Urea Precursors Driven NiCo2O4 Nanostructures Based Non-Enzymatic Urea Sensor for Milk and Urine Real Sample Applications
- 2023
-
In: Biosensors. - : MDPI. - 2079-6374. ; 13:4
-
Journal article (peer-reviewed)abstract
- The electrochemical performance of NiCo2O4 with urea precursors was evaluated in order to develop a non-enzymatic urea sensor. In this study, NiCo2O4 nanostructures were synthesized hydrothermally at different concentrations of urea and characterized using scanning electron microscopy and X-ray diffraction. Nanostructures of NiCo2O4 exhibit a nanorod-like morphology and a cubic phase crystal structure. Urea can be detected with high sensitivity through NiCo2O4 nanostructures driven by urea precursors under alkaline conditions. A low limit of detection of 0.05 and an analytical range of 0.1 mM to 10 mM urea are provided. The concentration of 006 mM was determined by cyclic voltammetry. Chronoamperometry was used to determine the linear range in the range of 0.1 mM to 8 mM. Several analytical parameters were assessed, including selectivity, stability, and repeatability. NiCo2O4 nanostructures can also be used to detect urea in various biological samples in a practical manner.
|
|
32. |
- Matthiesen, Isabelle, et al.
(author)
-
Metabolic Assessment of Human Induced Pluripotent Stem Cells-Derived Astrocytes and Fetal Primary Astrocytes : Lactate and Glucose Turnover
- 2022
-
In: Biosensors. - : MDPI AG. - 2079-6374. ; 12:10, s. 839-
-
Journal article (peer-reviewed)abstract
- Astrocytes represent one of the main cell types in the brain and play a crucial role in brain functions, including supplying the energy demand for neurons. Moreover, they are important regulators of metabolite levels. Glucose uptake and lactate production are some of the main observable metabolic actions of astrocytes. To gain insight into these processes, it is essential to establish scalable and functional sources for in vitro studies of astrocytes. In this study, we compared the metabolic turnover of glucose and lactate in astrocytes derived from human induced pluripotent stem cell (hiPSC)-derived Astrocytes (hiAstrocytes) as a scalable astrocyte source to human fetal astrocytes (HFAs). Using a user-friendly, commercial flow-based biosensor, we could verify that hiAstrocytes are as glycogenic as their fetal counterparts, but their normalized metabolic turnover is lower. Specifically, under identical culture conditions in a defined media, HFAs have 2.3 times higher levels of lactate production compared to hiAstrocytes. In terms of glucose, HFAs have 2.1 times higher consumption levels than hiAstrocytes at 24 h. Still, as we describe their glycogenic phenotype, our study demonstrates the use of hiAstrocytes and flow-based biosensors for metabolic studies of astrocyte function.
|
|
33. |
|
|
34. |
- Psotta, Carolin, et al.
(author)
-
Bacteria-Infected Artificial Urine Characterization Based on a Combined Approach Using an Electronic Tongue Complemented with 1H-NMR and Flow Cytometry
- 2023
-
In: Biosensors. - : MDPI. - 2079-6374. ; 13:10, s. 916-916
-
Journal article (peer-reviewed)abstract
- The prevailing form of bacterial infection is within the urinary tract, encompassing a wide array of bacteria that harness the urinary metabolome for their growth. Through their metabolic actions, the chemical composition of the growth medium undergoes modifications as the bacteria metabolize urine compounds, leading to the subsequent release of metabolites. These changes can indirectly indicate the existence and proliferation of bacterial organisms. Here, we investigate the use of an electronic tongue, a powerful analytical instrument based on a combination of non-selective chemical sensors with a partial specificity for data gathering combined with principal component analysis, to distinguish between infected and non-infected artificial urine samples. Three prevalent bacteria found in urinary tract infections were investigated, Escherichia coli, Klebsiella pneumoniae, and Enterococcus faecalis. Furthermore, the electronic tongue analysis was supplemented with 1H NMR spectroscopy and flow cytometry. Bacteria-specific changes in compound consumption allowed for a qualitative differentiation between artificial urine medium and bacterial growth.
|
|
35. |
- Ullah, Sadia Fida, et al.
(author)
-
An Experimental Framework for Developing Point-of-Need Biosensors : Connecting Bio-Layer Interferometry and Electrochemical Impedance Spectroscopy
- 2022
-
In: Biosensors. - : MDPI AG. - 2079-6374. ; 12:11
-
Journal article (peer-reviewed)abstract
- Biolayer interferometry (BLI) is a well-established laboratory technique for studying biomolecular interactions important for applications such as drug development. Currently, there are interesting opportunities for expanding the use of BLI in other fields, including the development of rapid diagnostic tools. To date, there are no detailed frameworks for implementing BLI in target-recognition studies that are pivotal for developing point-of-need biosensors. Here, we attempt to bridge these domains by providing a framework that connects output(s) of molecular interaction studies with key performance indicators used in the development of point-of-need biosensors. First, we briefly review the governing theory for protein-ligand interactions, and we then summarize the approach for real-time kinetic quantification using various techniques. The 2020 PRISMA guideline was used for all governing theory reviews and meta-analyses. Using the information from the meta-analysis, we introduce an experimental framework for connecting outcomes from BLI experiments (K-D, k(on), k(off)) with electrochemical (capacitive) biosensor design. As a first step in the development of a larger framework, we specifically focus on mapping BLI outcomes to five biosensor key performance indicators (sensitivity, selectivity, response time, hysteresis, operating range). The applicability of our framework was demonstrated in a study of case based on published literature related to SARS-CoV-2 spike protein to show the development of a capacitive biosensor based on truncated angiotensin-converting enzyme 2 (ACE2) as the receptor. The case study focuses on non-specific binding and selectivity as research goals. The proposed framework proved to be an important first step toward modeling/simulation efforts that map molecular interactions to sensor design.
|
|
36. |
- Velarte, Antonio, et al.
(author)
-
Fiber-Optic-Based System for High-Resolution Monitoring of Stretch in Excised Tissues
- 2023
-
In: Biosensors. - 2079-6374. ; 13:10
-
Journal article (peer-reviewed)abstract
- Cardiovascular diseases cause a high number of deaths nowadays. To improve these statistics, new strategies to better understand the electrical and mechanical abnormalities underlying them are urgently required. This study focuses on the development of a sensor to measure tissue stretch in excised tissues, enabling improved knowledge of biomechanical properties and allowing greater control in real time. A system made of biocompatible materials is described, which is based on two cantilevered platforms that integrate an optical fiber inside them to quantify the amount of stretch the tissues are exposed to with a precision of mu m. The operating principle of the sensor is based on the variation of the optical path with the movement of the platforms onto which the samples are fixed. The conducted tests highlight that this system, based on a simple topology and technology, is capable of achieving the desired purpose (a resolution of similar to 1 mu m), enabling the tissue to be bathed in any medium within the system.
|
|
37. |
- Zhang, Meizhen, et al.
(author)
-
Ultra-Sensitive, Rapid and On-Site Sensing Harmful Ingredients Used in Aquaculture with Magnetic Fluid SERS
- 2022
-
In: Biosensors. - : MDPI AG. - 2079-6374. ; 12:3
-
Journal article (peer-reviewed)abstract
- The integration of surface-enhanced Raman scattering (SERS) spectroscopy with magnetic fluid provides significant utility in point-of-care (POC) testing applications. Bifunctional magnetic–plasmonic composites have been widely employed as SERS substrates. In this study, a simple and cost-effective approach was developed to synthesize magnetic–plasmonic SERS substrates by decorating silver nanoparticles onto magnetic Fe3O4 nanoparticles (AgMNPs), which function both as SERS-active substrates and magnetic fluid particles. The strong magnetic responsivity from AgMNPs can isolate, concentrate, and detect target analytes from the irregular surface of fish skin rapidly. We fabricate a microfluid chip with three sample reservoirs that confine AgMNPs into ever smaller volumes under an applied magnetic field, which enhances the SERS signal and improves the detection limit by two orders of magnitude. The magnetic fluid POC sensor successfully detected malachite green from fish with excellent selectivity and high sensitivity down to the picomolar level. This work achieves a label-free, non-destructive optical sensing approach with promising potential for the detection of various harmful ingredients in food or the environment.
|
|