1. |
|
|
2. |
- Elsakka, Amr, et al.
(author)
-
A mm-Wave Phased-Array Fed Torus Reflector Antenna with ±30° Scan Range for Massive-MIMO Base-Station Applications
- 2022
-
In: IEEE Transactions on Antennas and Propagation. - 0018-926X .- 1558-2221. ; 70:5, s. 3398-3410
-
Journal article (peer-reviewed)abstract
- A phased-array fed reflector antenna system is presented which can be used for mm-wave base station applications. The proposed system is designed to support massive-Multi-Input-Multi-Output (MIMO) scenarios within a wide coverage (±30°) in the azimuth plane and a limited coverage at the elevation plane. A design and characterization methodology has been established to optimize the system for the operation in various line-of-sight conditions by adopting the maximum-ratio-transmission (MRT) and zero-forcing (ZF) MIMO algorithms. A two-user MIMO case study has been considered for the evaluation of the key system performance metrics, i.e. the effective isotropic radiated power, power consumption, signal-to-noise-ratio (SNR), and signal-to-interference-plus-noise-ratio (SINR). This study demonstrates that the phased-array fed reflector concept has a major advantage over traditional direct-radiating phased array (DRPA) antennas to reduce energy consumption. In the present example, it requires 12–14 dB less transmitted power as compared to the MRT-beamformed DRPAs for the same SNR, and 26–27 dB less transmitted power relatively to ZF-beamformed DRPA systems for the same SINR. A prototype, employing a 55 cm diameter torus reflector and operating at 28 GHz-band, has been manufactured and tested. The measurement results agree well with simulations.
|
|
3. |
- Anjos, Eduardo V.P., et al.
(author)
-
FORMAT: A Reconfigurable Tile-Based Antenna Array System for 5G and 6G Millimeter-Wave Testbeds
- 2022
-
In: IEEE Systems Journal. - 1932-8184 .- 1937-9234. ; 16:3, s. 4489-4500
-
Journal article (peer-reviewed)abstract
- This article introduces the FORMAT array, a reconfigurable millimeter-wave antenna array platform based on antenna tiles. FORMAT stands for Flexible Organization and Reconfiguration of Millimeter-wave Antenna Tiles, which is a unique hardware solution aiming to implement and demonstrate a variety of antenna array concepts, as well as different array architectures and configurations from the same basic module, providing even benchmark between different solutions and thus valuable insights into fifth-generation (5G) and beyond-5G antenna systems. The combination of a minimum-sized tile with 3D-printed frame parts enables antenna arrays of a variety of sizes, allows multiple beamforming architectures, and a range of different antenna element positioning in the array. The hardware implementation is thoroughly described, with a few different array assemblies being manufactured and measured, validating their antenna performance with over-the-air measurements. Finally, using FORMAT hardware as both base station and user equipment, a 5-m wireless communication link was set up, achieving 4.8 Gbps downlink speed with QAM64 modulation.
|
|
4. |
- Bressner, Thomas A.H., et al.
(author)
-
Cell Partitioning Antenna System Performance in Multi-User Scenarios for mmWave Communications
- 2021
-
In: IEEE Access. - 2169-3536 .- 2169-3536. ; 9, s. 127141-127149
-
Journal article (peer-reviewed)abstract
- Fixed-beam, high-gain antenna systems can be used for a finer partitioning of the currently used cell-sectoring. This partitioning has the benefit of reducing the number of users seen per antenna beam, which reduces interference. Furthermore, the high antenna gain allows for a high effective isotropic radiated power while keeping the transmit power low. In this paper, we study the performance of such a fixed-beam, high gain antenna system design for millimeter-wave mobile communications. The antenna system is designed to keep the inter-sector interference in a multi-site scenario low. The performance is analyzed for single- and multi-user environments. In single-input single-output mode, the 50th percentile of the signal-to-interference-plus-noise ratio lies between 12.5 dB to 39.7 dB if 3 to 0 interferers are present, respectively. For multiple-input multiple-output transmission using zero-forcing, the signal-to-interference-plus-noise ratio increases and the 50th percentile ranges from 36.1 dB to 43.3 dB if 3 to 0 interferes are present, respectively. By using maximum ratio transmission, the best performance is achieved with no interferers present, while a plunge in performance is observed with interferers. Furthermore, the study revealed that the narrow beam antenna system can also provide a clear signal separation for small spatial separations. In the given example, the signal-to-interference-plus-noise ratio is larger than 32.1 dB with 11 active antenna elements, where 2.8 meters separate the users. Hence, the paper shows that the cell-partitioning antenna systems provide coverage in the desired area while keeping the inter-sector interference low, and the considered transmission techniques can be used for situation optimized mobile communication links.
|
|
5. |
- Elsakka, Amr, 1984, et al.
(author)
-
A Design Concept of Power Efficient, High Gain Antenna System for mm-Waves Base Stations
- 2021
-
In: 2021 15TH EUROPEAN CONFERENCE ON ANTENNAS AND PROPAGATION (EUCAP). - 2164-3342.
-
Conference paper (peer-reviewed)abstract
- A design concept for a phased-array-fed reflector antenna system intended for millimeter-wave base stations is presented. This concept is motivated by the need for efficient beamforming antenna systems with reduced power consumption as compared to the presently considered fully-populated large-scale MIMO arrays. The main idea is to use a high-gain reflector antenna to maximize the effective isotropic radiated power. That in turn, allows minimizing the number of active antenna elements of the phased-array feed, and hence limit the total supplied power. The proposed reflector antenna system is based on a torus reflector which is illuminated by an offset phased-array feed. We show how to determine the antenna design parameters to achieve the desired cell coverage.
|
|