| 1. |
|
|
| 2. |
- Alsaffar, Abdul Kareem K., et al.
(author)
-
Development of eco-friendly wall insulation layer utilising the wastes of the packing industry
- 2023
-
In: Heliyon. - : Elsevier. - 2405-8440. ; 9:11
-
Journal article (peer-reviewed)abstract
- Efficient thermal insulation materials considerably lower power consumption for heating and cooling of buildings, which in turn minimises CO2 emissions and improves indoor comfort conditions. However, the selection of suitable insulation materials is governed by several factors, such as the environmental impact, health impact, cost and durability. Additionally, the disposal of used insulation materials is a major factor that affects the selection of materials because some materials could be very toxic for humans and the environment, such as asbestos-containing materials. Therefore, there is a continuous research effort, in both industry and academia, to develop sustainable and affordable insulation materials. In this context, this work aims at utilising the packing industry wastes (cardboard) to develop an eco-friendly insulation layer, which is a biodegradable material that can be disposed of safely after use. Experimentally, wasted cardboard was collected, cleaned, and soaked in water for 24 h. Then, the wet cardboard was minced and converted into past papers, then cast in square moulds and left in a ventilated oven at 75 °C to dry before de-moulding them. The produced layers were subjected to a wide range of tests, including thermal conductivity, acoustic insulation, infrared imaging and bending resistance. The obtained results showed the developed material has a good thermal and acoustic insulation performance. Thermally, the developed material had the lowest thermal conductivity (λ) (0.039 W/m.K) compared to the studied traditional materials. Additionally, it successfully decreased the noise level from 80 to about 58 dB, which was better than the efficiency of the commercial polyisocyanurate layer. However, the bending strength of the developed material was a major drawback because the material did not resist more than 0.6 MPa compared to 2.0 MPa for the commercial polyisocyanurate and 70.0 MPa for the wood boards. Therefore, it is recommended to investigate the possibility of strengthening the new material by adding fibres or cementitious materials.
|
|
| 3. |
- Hashim, Khalid S., et al.
(author)
-
Adsorption of fluoride on a green adsorbent derived from wastepaper: Kinetic, isotherm and characterisation study
- 2023
-
In: Case Studies in Chemical and Environmental Engineering. - : Elsevier. - 2666-0164. ; 8
-
Journal article (peer-reviewed)abstract
- The excessive concentration of fluoride (F−) in water represents a grave problem for several countries, especially those that depend on groundwater as a main source of drinking water. Therefore, many treatment methods, such as chemical precipitation and membrane, were practised to remove F− from water. However, the traditional methods suffer from many limitations, such as the high cost and the slowness. Hence, many studies have been directed towards developing novel and effective water defluoridation methods. In this context, the current study investigates the development of an eco-friendly adsorbent by extracting Ca, Al, and Fe from industrial by-products, precipitating them on sand particles, and using this new adsorbent to remove F− from water. The removal experiments were commenced under different pH levels (3-10), contact times (0–240 minutes) and concentrations of F− (7.5–37.5 mg/L). X-ray fluorescence (XRF), X-ray diffraction Investigator (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDX) methods were used to characterise the green adsorbent. Adsorption isotherm and kinetic studies were also conducted to define the adsorption type. The results confirmed that the new adsorbent could remove as high as 86% of F− at pH, contact time, agitation speed and adsorbent dose of 10, 180 minutes, 200 rpm and 15 mg/L, respectively. The characterisation studies prove the occurrence of the sorption process and the suitability of the morphology of the adsorbent for F− removal. Adsorption kinetics follow better with a pseudo-first-order model that indicates the predominance of physisorption, which agrees with the FTIR results. The isotherm study indicated that Langmuir isotherm is more suitable for representing data with an R2 value of 0.992, which means the adsorption of F− occurs as monolayer adsorption on homogeneous sites on the surface of the new adsorbent. In summary, it can be concluded that the developed adsorbent in this study could be a promising alternative to the traditional F− removal methods.
|
|
| 4. |
- Khudhair, Zahraa S., et al.
(author)
-
A Review of Hybrid Soft Computing and Data Pre-Processing Techniques to Forecast Freshwater Quality’s Parameters: Current Trends and Future Directions
- 2022
-
In: Environments. - : MDPI. - 2076-3298. ; 9:7
-
Journal article (peer-reviewed)abstract
- Water quality has a significant influence on human health. As a result, water quality parameter modelling is one of the most challenging problems in the water sector. Therefore, the major factor in choosing an appropriate prediction model is accuracy. This research aims to analyse hybrid techniques and pre-processing data methods in freshwater quality modelling and forecasting. Hybrid approaches have generally been seen as a potential way of improving the accuracy of water quality modelling and forecasting compared with individual models. Consequently, recent studies have focused on using hybrid models to enhance forecasting accuracy. The modelling of dissolved oxygen is receiving more attention. From a review of relevant articles, it is clear that hybrid techniques are viable and precise methods for water quality prediction. Additionally, this paper presents future research directions to help researchers predict freshwater quality variables.
|
|
