SwePub
Sök i SwePub databas

  Extended search

Träfflista för sökning "WFRF:(Jansson Ulf 1960 ) "

Search: WFRF:(Jansson Ulf 1960 )

  • Result 1-50 of 73
Sort/group result
   
EnumerationReferenceCoverFind
1.
  •  
2.
  • Jansson, Anna, et al. (author)
  • Magnetron sputtering of the high entropy alloy CoCrFeMnNi on 316L : Influence of substrate grain orientations
  • 2023
  • In: Surface & Coatings Technology. - : Elsevier. - 0257-8972 .- 1879-3347. ; 466
  • Journal article (peer-reviewed)abstract
    • This study explores the influence of a 316L stainless steel substrate on the magnetron sputtering of the Cantor alloy CoCrFeMnNi at different substrate bias. The study was carried out on a polycrystalline 316L substrate where the growth behavior of the coating could be investigated on grains with different orientations. By combining electron backscatter diffraction (EBSD) before and after deposition and characterization of the same area, it was possible to determine growth behaviour and surface morphologies on individual substrate grains. No strong influence of the substrate was observed at a floating bias. At a bias of -100V, however, the coating was strongly influenced by the orientation of the individual substrate grains.  Epitaxial coating grains with a smooth surface were observed on the [102]-oriented grains while a more columnar growth was observed on [111]-oriented grains.  Furthermore, a small difference in growth rate was observed on different substrate orientations. The growth behaviour could be related to differences in surface energies and diffusion rates on different surface orientations.
  •  
3.
  • Kádas, Krisztina, et al. (author)
  • AlM2B2 (M = Cr, Mn, Fe, Co, Ni) : a group of nanolaminated materials
  • 2017
  • In: Journal of Physics. - : Institute of Physics Publishing (IOPP). - 0953-8984 .- 1361-648X. ; 29:15
  • Journal article (peer-reviewed)abstract
    • Combining theory with experiments, we study the phase stability, elastic properties, electronic structure and hardness of layered ternary borides AlCr2B2, AlMn2B2, AlFe2B2, AlCo2B2, and AlNi2B2. We find that the first three borides of this series are stable phases, while AlCo2B2 and AlNi2B2 are metastable. We show that the elasticity increases in the boride series, and predict that AlCr2B2, AlMn2B2, and AlFe2B2 are more brittle, while AlCo2B2 and AlNi2B2 are more ductile. We propose that the elasticity of AlFe2B2 can be improved by alloying it with cobalt or nickel, or a combination of them. We present evidence that these ternary borides represent nanolaminated systems. Based on SEM measurements, we demonstrate that they exhibit the delamination phenomena, which leads to a reduced hardness compared to transition metal mono-and diborides. We discuss the background of delamination by analyzing chemical bonding and theoretical work of separation in these borides.
  •  
4.
  • Berastegui, Pedro, et al. (author)
  • Magnetron Sputtering of Nanolaminated Cr2AlB2
  • 2020
  • In: Coatings. - : MDPI. - 2079-6412. ; 10:8
  • Journal article (peer-reviewed)abstract
    • A ternary Cr(2)AlB(2)phase was deposited as a film using magnetron sputtering. Its anisotropic structure displays both structural and chemical similarities with the nanolaminated MAX phases (M(n+1)AX(n)(n = 1-3) where M usually is an early transition metal, A is typically an element in group 13-14 and X is C or N), and can be described as CrB slabs separated by layers of Al. Combinatorial sputtering was used to optimise the sputtering process parameters for films with the Cr(2)AlB(2)composition. The influences of substrate, temperature and composition were studied using X-ray diffraction, X-ray photoelectron spectroscopy and electron microscopy. Films deposited at room temperature were X-ray amorphous but crystalline films could be deposited on MgO substrates at 680 degrees C using a composite Al-B, Cr and Al targets. X-ray diffraction analyses showed that the phase composition and texture of the films was strongly dependent on the chemical composition. Films with several phases or with a single Cr(2)AlB(2)phase could be deposited, but an additional Al target was required to compensate for a loss of Al at the high deposition temperatures used in this study. The microstructure evolution during film growth was strongly dependent on composition, with a change in texture in Al-rich films from a preferred [010] orientation to a [100]/[001] orientation. A model based on Al desorption from the surface of the growing grains is proposed to explain the texture variations.
  •  
5.
  • Braceras, Inigo, et al. (author)
  • On the electro-tribological properties and degradation resistance of silver-aluminum coatings
  • 2018
  • In: Wear. - : ELSEVIER SCIENCE SA. - 0043-1648 .- 1873-2577. ; 414, s. 202-211
  • Journal article (peer-reviewed)abstract
    • Contact materials in sliding electrical applications must possess low electrical contact resistance, low friction and wear coefficients, and high degradation resistance to the surrounding media. Silver coatings are commonly used in such applications despite their shortcomings. This work has focused on the study of alternative silver-aluminum coatings deposited by PVD. The main findings include the strong dependence of the tribological performance on the concentration of Al and hence the phases present in the coatings. Besides, the wear mechanism was found to be affected by the working media, either on air or insulating oil. Results have shown that for full HCP phase coatings (Ag67Al33), wear rates are lowest, with no adhesive wear and good surface sulphidation resistance, though with some proclivity to oxidation, coupled with a moderate increase in the electrical contact resistance.
  •  
6.
  • Casillas Trujillo, Luis, et al. (author)
  • Experimental and theoretical evidence of charge transfer in multi-component alloys : how chemical interactions reduce atomic size mismatch
  • 2021
  • In: Materials Chemistry Frontiers. - : Royal Society of Chemistry. - 2052-1537. ; 5:15, s. 5746-5759
  • Journal article (peer-reviewed)abstract
    • Ab initio simulations of a multi-component alloy using density functional theory (DFT) were combined with experiments on thin films of the same material using X-ray photoelectron spectroscopy (XPS) to study the connection between the electronic and atomic structures of multi-component alloys. The DFT simulations were performed on an equimolar HfNbTiVZr multi-component alloy. Structure and charge transfer were evaluated using relaxed, non-relaxed, as well as elemental reference structures. The use of a fixed sphere size model allowed quantification of charge transfer, and separation into different contributions. The charge transfer was generally found to follow electronegativity trends and results in a reduced size mismatch between the elements, and thus causes a considerable reduction of the lattice distortions compared to a traditional assumption based on tabulated atomic radii. A calculation of the average deviation from the average radius (i.e. the so-called δ-parameter) based on the atomic Voronoi volumes gave a reduction of δ from ca. 6% (using the volumes in elemental reference phases) to ca. 2% (using the volumes in the relaxed multi-component alloy phase). The reliability of the theoretical results was confirmed by XPS measurements of a Hf22Nb19Ti18V19Zr21 thin film deposited by sputter deposition. The experimentally observed core level binding energy shifts (CLS), as well as peak broadening due to a range of chemical surroundings, for each element showed good agreement with the calculated DFT values. The single solid solution phase of the sample was confirmed by X-ray diffraction (XRD) and transmission electron microscopy (TEM) including energy dispersive spectroscopy (EDS) with nm-resolution. These observations show that the HfNbTiVZr solid solution phase is non-ideal, and that chemical bonding plays an important part in the structure formation, and presumably also in the properties. Our conclusions should be transferable to other multi-component alloy systems, as well as some other multi-component material systems, and open up interesting possibilities for the design of material properties via the electronic structure and controlled charge transfer between selected metallic elements in the materials.
  •  
7.
  • Casillas Trujillo, Luis, et al. (author)
  • Interstitial carbon in bcc HfNbTiVZr high-entropy alloy from first principles
  • 2020
  • In: Physical Review Materials. - : AMER PHYSICAL SOC. - 2475-9953. ; 4:12
  • Journal article (peer-reviewed)abstract
    • The remarkable mechanical properties of high-entropy alloys can be further improved by interstitial alloying. In this work we employ density functional theory calculations to study the solution energies of dilute carbon interstitial atoms in tetrahedral and octahedral sites in bcc HfNbTiVZr. Our results indicate that carbon interstitials in tetrahedral sites are unstable, and the preferred octahedral sites present a large spread in the energy of solution. The inclusion of carbon interstitials induces large structural relaxations with long-range effects. The effect of local chemical environment on the energy of solution is investigated by performing a local cluster expansion including studies of its correlation with the carbon atomic Voronoi volume. However, the spread in solution energetics cannot be explained with a local environment analysis only pointing towards a complex, long-range influence of interstitial carbon in this alloy.
  •  
8.
  • Cedervall, Johan, et al. (author)
  • Magnetic and mechanical effects of Mn substitutions in AlFe2B2
  • 2019
  • In: Journal of Magnetism and Magnetic Materials. - : Elsevier BV. - 0304-8853 .- 1873-4766. ; 482, s. 54-60
  • Journal article (peer-reviewed)abstract
    • The mechanical and magnetic properties of the newly discovered MAB-phase class of materials based upon AlFe2B2 were investigated. The samples were synthesised from stoichiometric amounts of all constituent elements. X-ray diffraction shows that the main phase is orthorhombic with an elongated b-axis, similar to AlFe2B2. The low hardness and visual inspection of the samples after deformation indicate that these compounds are deformed via a delamination process. When substituting iron in AlFe2B2 with manganese, the magnetism in the system goes from being ferro- to antiferromagnetic via a disordered ferrimagnetic phase exhibited by AlFeMnB2. Density functional theory calculations indicate a weakening of the magnetic interactions among the transitions metal ions as iron is substituted by manganese in AlFe2B2. The Mn-Mn exchange interactions in AlMn2B2 are found to be very small.
  •  
9.
  • Chou, Chia-Ying, et al. (author)
  • Precipitation Kinetics During Post-heat Treatment of an Additively Manufactured Ferritic Stainless Steel
  • 2022
  • In: Metallurgical and Materials Transactions. A. - : Springer Nature. - 1073-5623 .- 1543-1940. ; 53:8, s. 3073-3082
  • Journal article (peer-reviewed)abstract
    • The microstructure response of laser-powder bed fusion (L-PBF)-processed ferritic stainless steel (AISI 441) during post-heat treatments is studied in detail. Focus is on the precipitation kinetics of the Nb-rich phases: Laves (Fe2Nb) and the cubic carbo-nitride (NbC), as well as the grain structure evolution. The evolution of the precipitates is characterized using scanning and transmission electron microscopy (SEM and TEM) and the experimental results are used to calibrate precipitation kinetics simulations using the precipitation module (TC-PRISMA) within the Thermo-Calc Software package. The calculations reproduce the main trend for both the mean radii for the Laves phase and the NbC, and the amount of Laves phase, as a function of temperature. The calibrated model can be used to optimize the post-heat treatment of additively manufactured ferritic stainless steel components and offer a creator tool for process and structure linkages in an integrated computational materials engineering (ICME) framework for alloy and process development of additively manufactured ferritic steels.
  •  
10.
  • Ekberg-Jansson, Ann, 1960, et al. (author)
  • Bronchial mucosal mast cells in asymptomatic smokers relation to structure, lung function and emphysema
  • 2005
  • In: Respir Med. - : Elsevier BV. - 0954-6111 .- 1532-3064. ; 99:1, s. 75-83
  • Journal article (peer-reviewed)abstract
    • The pathologic mechanisms of chronic obstructive pulmonary disease (COPD) most certainly involves neutrophil granulocytes, cytotoxic T-cells, macophages and mast cells. The aim of this study was to investigate the relation between the number of mast cells in different compartments in bronchial biopsies of central proximal airways to structural changes, lung function tests and emphysema detected by high resolution computed tomography (HRCT). Twenty nine asymptomatic smoking and 16 never-smoking men from a population study were recruited. Central bronchial biopsies were stained to identify mast cells by immunohistochemistry. The number of mast cells in the epithelium, lamina propria and smooth muscle as well as epithelial integrity and thickness of the tenascin and laminin layer were determined. Smokers had increased numbers of mast cells in all compartments (P<0.001). Structural changes were correlated to mast cell numbers with the closest associations to mast cell numbers in the smooth muscle [epithelial integrity (R(S)=-0.48, P=0.008), laminin layer (R(S)=0.63, P=0.0002), tenascin layer (R(S)=0.40, P=0.03)]. Similar correlations between mast cells and lung function tests were seen [functional residual capacity (FRC) (R(S)=0.60, P=0.0006), total lung capacity (TLC) (R(S)=0.44, P=0.02) and residual volume (RV) (R(S)=0.41, P=0.03)]. No correlations could be detected between mast cells and FEV1 or to emphysema. Smoking is associated with an increase of mast cells in all compartments of the bronchial mucosa, including smooth muscle, and this is related to altered airway structure and function.
  •  
11.
  •  
12.
  • Emmerlich, Jens, 1974-, et al. (author)
  • Growth of Ti3SiC2 thin films by elemental target magnetron sputtering
  • 2004
  • In: Journal of Applied Physics. - : AIP Publishing. - 0021-8979 .- 1089-7550. ; 96:9, s. 4817-4826
  • Journal article (peer-reviewed)abstract
    • Epitaxial Ti3SiC2(0001) thin films have been deposited by dc magnetron sputtering from three elemental targets of Ti, C, and Si onto MgO(111) and Al2O3(0001) substrates at temperatures of 800–900 °C. This process allows composition control to synthesize Mn + 1AXn (MAX) phases (M: early transition metal; A: A-group element; X: C and/or N; n = 1–3) including Ti4SiC3. Depositions on MgO(100) substrates yielding the Ti–Si–C MAX phases with (105), as the preferred orientation. Samples grown at different substrate temperatures, studied by means of transmission electron microscopy and x-ray diffraction investigations, revealed the constraints of Ti3SiC2 nucleation due to kinetic limitations at substrate temperatures below 700 °C. Instead, there is a competitive TiCx growth with Si segregation to form twin boundaries or Si substitutional incorporation in TiCx. Physical properties of the as-deposited single-crystal Ti3SiC2 films were determined. A low resistivity of 25 µ cm was measured. The Young's modulus, ascertained by nanoindentation, yielded a value of 343–370 GPa. For the mechanical deformation response of the material, probing with cube corner and Berkovich indenters showed an initial high hardness of almost 30 GPa. With increased maximum indentation loads, the hardness was observed to decrease toward bulk values as the characteristic kink formation sets in with dislocation ordering and delamination at basal planes.
  •  
13.
  • Fritze, Stefan, et al. (author)
  • Elemental distribution and fracture properties of magnetron sputtered carbon supersaturated tungsten films
  • 2024
  • In: Surface & Coatings Technology. - : Elsevier BV. - 0257-8972 .- 1879-3347. ; 477
  • Journal article (peer-reviewed)abstract
    • The combination of strength and toughness is a major driving force for alloy design of protective coatings, and nanocrystalline tungsten (W)-alloys have shown to be promising candidates for combining strength and toughness. Here we investigate the elemental distribution and the fracture toughness of carbon (C) alloyed W thin films prepared by non-reactive magnetron sputtering. W:C films with up to ~4 at.% C crystallize in a body-centered-cubic structure with a strong 〈hh0〉texture, and no additional carbide phases are observed in the diffraction pattern. Atom probe tomography and X-ray photoelectron spectroscopy confirmed the formation of such a supersaturated solid solution. The pure W film has a hardness ~13 GPa and the W:C films exhibit a peak hardness of ~24 GPa. In-situ micromechanical cantilever bending tests show that the fracture toughness decreases from ~4.5 MPa·m1/2 for the W film to ~3.1 MPa·m1/2 for W:C films. The results show that C can significantly enhance the hardness of W thin films while retaining a high fracture toughness.
  •  
14.
  • Fritze, Stefan, et al. (author)
  • Hard and crack resistant carbon supersaturated refractory nanostructured multicomponent coatings
  • 2018
  • In: Scientific Reports. - : NATURE PUBLISHING GROUP. - 2045-2322. ; 8
  • Journal article (peer-reviewed)abstract
    • The combination of ceramic hardness with high crack resistance is a major challenge in the design of protective thin films. High entropy alloys have shown in earlier studies promising mechanical properties with a potential use as thin film materials. In this study, we show that small amounts of carbon in magnetron-sputtered multicomponent CrNbTaTiW films can lead to a significant increase in hardness. The film properties were strongly dependent on the metal composition and the most promising results were observed for TaW-rich films. They crystallised in a bcc structure with a strong (110) texture and coherent grain boundaries. It was possible to deposit films with 8 at.% C in a supersaturated solid-solution into the bcc structure without carbide formation. A major effect of carbon was a significant grain refinement, reducing the column diameter from approximately 35 to 10 nm. This resulted in an increase in hardness from 14.7 to 19.1 GPa while the reduced E-modulus stayed constant at 322 GPa. The carbon-containing films exhibited extremely little plastic deformation around the indent and no cracks were observed. These results show that supersaturation of carbon into high entropy films can be a promising concept to combine superior hardness with high crack resistance.
  •  
15.
  • Fritze, Stefan, et al. (author)
  • Influence of Carbon on Microstructure and Mechanical Properties of Magnetron Sputtered TaW Coatings
  • 2020
  • In: Materials & design. - : Elsevier. - 0264-1275 .- 1873-4197. ; 196
  • Journal article (peer-reviewed)abstract
    • (Ta,W) and (Ta,W):C films with-5 at.% C were deposited by non-reactive magnetron sputtering. They crystallised in a bcc structure with a columnar microstructure. The solid solubility of C in (Ta,W) alloys is very low, which suggests that the (Ta,W):C films are supersaturated with respect to carbon. This was confirmed by diffraction and atom probe tomography (APT) showing that carbon is in the as-deposited (Ta,W):C films homogeneously distributed in the structure without carbide formation or carbon segregation. Annealing at 900 degrees C for 2 h showed no significant column coarsening but an increased defect density at the column boundaries in the (Ta,W):C films. The films were still supersaturated with respect to carbon but APT showed a partial segregation of carbon presumably to defect-rich column boundaries after annealing. The (Ta,W) films exhibited a hardness of-12-13 GPa. Alloying with carbon increased the hardness to-17 GPa. The hardness increased to-19 GPa for the annealed (Ta,W):C films. This annealing-induced hardness increase was explained by C segregation to the more defect-rich column boundaries, which restricts dislocation movements. (Ta,W):C coatings may be a potential alternative to ceramic coatings, worth exploring further by small scale mechanical testing to investigate if these materials are ductile.
  •  
16.
  • Fritze, Stefan, et al. (author)
  • Influence of Deposition Temperature on the Phase Evolution of HfNbTiVZr High-Entropy Thin Films
  • 2019
  • In: Materials. - : MDPI. - 1996-1944. ; 12:4
  • Journal article (peer-reviewed)abstract
    • In this study, we show that the phase formation of HfNbTiVZr high-entropy thin films is strongly influenced by the substrate temperature. Films deposited at room temperature exhibit an amorphous microstructure and are 6.5 GPa hard. With increasing substrate temperature (room temperature to 275 degrees C), a transition from an amorphous to a single-phased body-centred cubic (bcc) solid solution occurs, resulting in a hardness increase to 7.9 GPa. A higher deposition temperature (450 degrees C) leads to the formation of C14 or C15 Laves phase precipitates in the bcc matrix and a further enhancement of mechanical properties with a peak hardness value of 9.2 GPa. These results also show that thin films follow different phase formation pathways compared to HfNbTiVZr bulk alloys.
  •  
17.
  • Fritze, Stefan, et al. (author)
  • Magnetron sputtering of carbon supersaturated tungsten films-A chemical approach to increase strength
  • 2021
  • In: Materials & design. - : Elsevier. - 0264-1275 .- 1873-4197. ; 208
  • Journal article (peer-reviewed)abstract
    • Tungsten (W)-based materials attract significant attention due to their superior mechanical properties. Here, we present a chemical approach based on the addition of carbon (C) for increased strength via the combination of three strengthening mechanisms in W thin films. W:C thin films with C concentrations up to-4 at.% were deposited by magnetron sputtering. All films exhibit a body-centred-cubic structure with strong texture and columnar growth behaviour. X-ray and electron diffraction measurements suggest the formation of supersaturated W:C solid solution phases. The addition of C reduced the average column width from-133 nm for W to-20 nm for the film containing-4 at.% C. The column refinement is explained by a mechanism where C acts as re-nucleation sites. The W film is-13 GPa hard, while the W:C films achieve a peak hardness of-24 GPa. The W:C films are-11 GPa harder than the W film, which is explained by a combination of grain refinement strengthening, solid solution strengthening and increased dislocation density. Additional micropillar compression tests showed that the flow stress increased upon C addition, from-3.8 to-8.3 GPa and no brittle fracture was observed.
  •  
18.
  • Fritze, Stefan (author)
  • Microstructure and Mechanical Properties of Magnetron Sputtered Refractory Metal Thin Films
  • 2020
  • Doctoral thesis (other academic/artistic)abstract
    • The design and development of new multifunctional materials that exhibit a combination of high hardness and ductility, as well as a high corrosion resistance and thermal stability, is one of the key challenges in the field of material science. The focus of this thesis is on the development of novel multifunctional magnetron sputtered CrNbTaTiW–C based thin films. Carbon was selected as an alloying element to investigate if it could modify the microstructure (via grain refinement) and improve the properties (e.g. the hardness and ductility).TaW-rich and near-equimolar high entropy alloys in the CrNbTaTiW system were selected as starting points for this study. The latter alloys were predicted, based on empirical design rules, to form a single-phase solid solution. In contrast, thermodynamic calculations showed that the films at equilibrium should be composed of a mixture of several phases at temperatures below 1100 °C.  Experimentally, however, a single-phase bcc structure was observed for the deposited films and it was concluded that the films were kinetically and not entropy stabilised. A hypothesis is that the kinetics during sputtering allow a ’direct’ phase selection by tuning the process parameters and evidence of this was found in the HfNbTiVZr alloy system.The CrNbTaTiW–C system is, however, complex and additional studies were carried out on the W–C and TaW–C systems. All metallic films crystallised in a bcc structure with a <110> texture and the column width of these films varied between 25 nm and 80 nm. The films were very hard (~ 13 GPa), which was explained by the small grain size. A single-phase bcc structure was also obtained upon the addition of 5-10 at.% carbon for all compositions except the near-equimolar CrNbTaTiW. X-ray diffraction indicated a unit cell expansion, which was attributed to the formation of a supersaturated solid solution. Additional atom probe tomography (APT) studies on selected samples confirmed the formation of such solid solutions. The supersaturated solid solution is not thermodynamically stable and an annealing study showed that heat treatment yielded segregation and clustering of carbon at the grain boundaries. The addition of carbon had a grain refining effect in the W–C system and the multicomponent CrNbTaTiW–C system. In general, the addition of carbon increased the hardness, which was mainly caused by a reduced grain size in line with the Hall-Petch relationship. Excellent mechanical properties of carbon supersaturated films were further confirmed in pillar tests on W–C films, which showed very high yield strength (~ 9 GPa) and no brittle fracture. The results show that carbon can be used as a chemical approach to control the grain size and properties of these films. Multicomponent carbides with a B1 structure were formed at high carbon concentrations (~ 40 at.%). The microstructure of these films depended strongly on the process parameters and a higher deposition temperature was found to increase the film density and hardness. The TaW-rich carbide exhibited a very high hardness of ~ 35 GPa and excellent corrosion resistance.
  •  
19.
  • Goetz, Inga K., 1992-, et al. (author)
  • Convective Flow Redistribution of Oxygen by Laser Melting of a Zr-Based Amorphous Alloy
  • 2023
  • In: Materials. - : MDPI. - 1996-1944. ; 16:11
  • Journal article (peer-reviewed)abstract
    • Oxygen impurities play a crucial role in the glass-forming ability and crystallisation behaviour of metallic glasses. In the present work, single laser tracks were produced on Zr59.3-xCu28.8 Al10.4Nb1.5Ox substrates (x = 0.3, 1.3) to study the redistribution of oxygen in the melt pool under laser melting, which provides the basis for laser powder bed fusion additive manufacturing. Since such substrates are commercially not available, they were fabricated by arc melting and splat quenching. X-ray diffraction revealed that the substrate with 0.3 at.% oxygen was X-ray amorphous, while the substrate with 1.3 at.% oxygen was partially crystalline. Hence, it is evident that the oxygen content affects the crystallisation kinetics. Subsequently, single laser tracks were produced on the surface of these substrates, and the melt pools attained from the laser processing were characterised by atom probe tomography and transmission electron microscopy. Surface oxidation and subsequent convective flow redistribution of oxygen by laser melting were identified as causes of the presence of CuOx and crystalline ZrO nanoparticles in the melt pool. Bands of ZrO likely originate from surface oxides that were moved deeper into the melt pool by convective flow. The findings presented here highlight the influence of oxygen redistribution from the surface into the melt pool during laser processing.
  •  
20.
  • Goetz, Inga Katharina, 1992- (author)
  • Local structure and composition : in additively manufactured bulk metallic glasses and composites
  • 2023
  • Doctoral thesis (other academic/artistic)abstract
    • Additive manufacturing enables the production of complex multi-material geometries and bulk metallic glass parts beyond their critical casting thickness. The local modification of structure, composition, and properties is explored in this thesis with the aim to design novel composite materials and functional gradients. The present work contributes to the process understanding required to produce bulk metallic glass composites in the laser powder bed fusion process. The investigated material systems include zirconium and iron based metallic glasses, metallic glass - nitride composites, as well as laser nitriding of titanium.The onset of devitrification of metallic glasses due to the processing or post-processing heat treatments induces the formation of nanoscale clusters. Features of > 1 nm can be detected and reliably distinguished from random fluctuations by atom probe tomography. The progression of crystallisation depends on the oxygen content of the samples and the applied heating or cooling rates. In-depth understanding of the crystallisation processes can be used to optimise both compositions and processing conditions. The process atmosphere contains reactive species such as oxygen or nitrogen, which can be incorporated during different stages of processing by surface oxidation of the powder or substrate pieces as well as by reactions with the gas during processing. While an inert gas atmosphere with a low residual oxygen content is sufficient to hinder reactions with residual oxygen, a nitrogen atmosphere can be used for local laser nitriding and, thus, the fabrication of metallic glass – ceramic composites. Due to the decompositions of nitrides formed in the preceding process steps and the tendency of a metallic glass matrix to crystallise, which limits the processing conditions, the incorporation of nitrogen is restricted to the first few hundred nm from the surface for a Zr-based amorphous alloy. In titanium, as a crystalline example, nitrogen is incorporated throughout the molten pool.The nitride composites exhibit increased hardness depending on the local nitride fraction, which can thus be used to fabricate specific property gradients within or on a printed piece. With optimised process parameters, the amorphous fraction of a printed Fe-based bulk metallic glass can be tailored for improved soft magnetic properties.
  •  
21.
  •  
22.
  •  
23.
  • Götz, Inga Katharina, 1992-, et al. (author)
  • Reactive metal additive manufacturing : Surface near ZrN - metallic glass composite formation and mechanical properties
  • 2023
  • In: Additive Manufacturing. - : Elsevier. - 2214-8604 .- 2214-7810. ; 66
  • Journal article (other academic/artistic)abstract
    • ZrN formation in a Zr-based bulk metallic glass is observed after processing using reactive laser powder bed fusion. Two processing routes employing nitrogen as a reactive process gas are explored: (1) Standard inert processing in argon followed by reactive remelting in nitrogen and (2) reactive processing in nitrogen. Incorporation of nitrogen is depth-dependent and both approaches result in a dispersion of ZrN nanocrystals in the amorphous matrix close to the surface. The process parameters can be adjusted to control the volume fraction of crystalline phases formed. Hence, it is shown that reactive additive manufacturing can be utilised to form bulk metallic glass-ceramic composites in surface near regions. Thereby we demonstrate that the reactive gas atmosphere utilised during additive manufacturing enables local tailoring of structure, composition, and mechanical properties in the vicinity of the surface.
  •  
24.
  • Haux, Caroline, 1960- (author)
  • Framkallning : Skrift, konsumtion och sexualitet i Karin Boyes Astarte och Henry Parlands Sönder
  • 2013
  • Doctoral thesis (other academic/artistic)abstract
    • This thesis is a comparative study in two novels which both try to understand modern life. The novels were both written between 1929 and 1930 as entries for the same major Nordic novel contest – Astarte in Sweden by Karin Boye, Sönder [To Pieces ]in Finland by the Finno-swedish author Henry Parland.This analysis tries to determine what is at stake in these novels by, apart from investigating them as novels in their own right, examining the complex interaction between a specific moment in history and the representation of that moment as literary text. The novels are examined as events in a specific historical situation; that is, how they write what is contemporary into themselves, trough answering the question about the historical moment that they themselves formulate. Four issues are fundamental to the study: The function of consumption and the commodity form in the novels. The way in which these novels render sexuality and desire. How other media forms function as aesthetic technologies for the novels. Lastly, aesthetics, writing and allegory: how the novels reflect on the possibility of representing this societal moment in history.A focus in the analysis is how woman is called forth as golden statue and photography, how she by letting herself be consumed as sexual symbol elicits male speech – thereby also making the speaker into author, and man. The economic side to this is the way in which men and women take on the form of commodities amongst themselves. It is in this sexual economy that they become men and women. The transformation of the sexed object into the systematic status of a sign, signifying its value, implies the simultaneous transformation of human relations into consumer relations: You consume or get consumed.
  •  
25.
  •  
26.
  • Holmberg, Max, et al. (author)
  • On Surface Losses in Direct Metal Laser Sintering Printed Millimeter and Submillimeter Waveguides
  • 2018
  • In: Journal of Infrared, Millimeter and Terahertz Waves. - : SPRINGER. - 1866-6892 .- 1866-6906. ; 39:6, s. 535-545
  • Journal article (peer-reviewed)abstract
    • Different lengths of WR3 (220-330 GHz) and WR10 (75-110 GHz) waveguides are fabricated through direct metal laser sintering (DMLS). The losses in these waveguides are measured and modelled using the Huray surface roughness model. The losses in WR3 are around 0.3 dB/mm and in WR10 0.05 dB/mm. The Huray equation model is accounting relatively good for the attenuation in the WR10 waveguide but deviates more in the WR3 waveguide. The model is compared to finite element simulations of the losses assuming an approximate surface structure similar to the resulting one from the DMLS process.
  •  
27.
  •  
28.
  • Högberg, Hans, 1968-, et al. (author)
  • Growth and characterization of MAX-phase thin films
  • 2005
  • In: Surface and Coatings Technology. - : Elsevier BV. - 0257-8972 .- 1879-3347. ; 193, s. 6-10
  • Journal article (peer-reviewed)abstract
    • We report that magnetron sputtering can be applied to synthesize MAX-phase films of several systems including Ti–Si–C, Ti–Ge–C, Ti–Al–C, and Ti–Al–N. In particular, epitaxial films of the known phases Ti3SiC2, Ti3GeC2, Ti2GeC, Ti3AlC2, Ti2AlC, and Ti2AlN as well as the newly discovered thin film phases Ti4SiC3, Ti4GeC3 and intergrown structures can be deposited at 900–1000 °C on Al2O3(0001) and MgO(111) pre-seeded with TiC or Ti(Al)N. From XTEM and AFM we suggest a growth and nucleation model where MAX-phase nucleation is initiated at surface steps or facets on the seed layer and followed by lateral growth. Differences between the growth behavior of the systems with respect to phase distribution and phase stabilities are discussed. Characterization of mechanical properties for Tin+1Si–Cn films with nanoindentation show decreased hardness from about 25 to 15 GPa upon penetration of the basal planes with characteristic large plastic deformation with pile up dependent on the choice of MAX material. This is explained by cohesive delamination of the basal planes and kink band formation, in agreement with the observations made for bulk material. Measurements of the electrical resistivity for Ti–Si–C and Ti–Al–N films with four-point probe technique show values of 30 and 39 μΩ cm, respectively, comparable to bulk materials.
  •  
29.
  • Jansson, Ulf, 1960-, et al. (author)
  • Carbon-containing multi-component thin films
  • 2019
  • In: Thin Solid Films. - : Elsevier BV. - 0040-6090 .- 1879-2731. ; 688
  • Research review (peer-reviewed)abstract
    • High entropy alloys (HEAs) have been a hot research area for many years. They are solid solutions of at least five elements in approximately equimolar compositions. The HEAs are assumed to be stabilized by a high entropy of mixing favouring a solid solution phase instead of a mixture of intermetallic phases. The importance of entropy of mixing and the true nature of HEAs are debated but the concept has contributed to an interesting development of new alloys. They idea of stabilizing solid solutions with many elements have recently been expanded to nitrides, borides, oxides and carbides. Furthermore, a growing number of thin film studies of these compounds are now published. In this paper we summarise recent results from studies of carbon-containing multi-component thin films based on the HEA concept. We will summarise some general observations connected to "high-entropy" materials. We also describe some general trends in metal-carbon interactions for transition metals and discuss how they should influence the formation of multi-component carbides. A summary of results on bulk multi-component carbide materials is also presented. We review published studies of carbon-containing multi-component thin films mainly deposited with magnetron-sputtering. The crystal structure, microstructure and properties of these films are described. Finally, we highlight some interesting topics for future research.
  •  
30.
  • Kadas, Krisztina, et al. (author)
  • Structural properties of amorphous metal carbides : Theory and experiment
  • 2012
  • In: Acta Materialia. - : Elsevier BV. - 1359-6454 .- 1873-2453. ; 60:12, s. 4720-4728
  • Journal article (peer-reviewed)abstract
    • By means of theoretical modeling and experimental synthesis and characterization, we investigate the structural properties of amorphous Zr-Si-C. Two chemical compositions are selected: Zr0.31Si0.29C0.40 and Zr0.60Si0.33C0.07. Amorphous structures are generated in the theoretical part of our work by the stochastic quenching (SQ) method, and detailed comparison is made regarding the structure and density of the experimentally synthesized films. These films are analyzed experimentally using X-ray absorption spectroscopy, transmission electron microscopy and X-ray diffraction. Our results demonstrate a remarkable agreement between theory and experiment concerning bond distances and atomic coordination of this complex amorphous metal carbide. The demonstrated power of the SQ method opens up avenues for theoretical predictions of amorphous materials in general.
  •  
31.
  • Karlsson, Dennis, 1991- (author)
  • Additive Manufacturing of Ferritic Materials : A Journey from Stainless Steels to High-Entropy Alloys
  • 2021
  • Doctoral thesis (other academic/artistic)abstract
    • Design of new materials with complex geometries is an important part of new innovative solutions for technical applications. With the use of additive manufacturing (AM), the design possibilities are endless and geometries that are impossible to manufacture by conventional techniques are available. However, the number of alloys commercially available is limited and extensive research is needed to establish new materials with unique properties. An important group of materials is ferritic stainless steels which have a body centered cubic crystal structure. They are often used for their high strength, corrosion resistance or electrical properties at high temperatures. However, they are often less ductile than austenitic stainless steels and issues with cracking may arise during thermal cycling in the L-PBF process. In this thesis, two AM techniques, laser powder bed fusion (L-PBF) and binder jetting were used to produce components of two different ferritic stainless steels and of the AlCoCrFeNi high-entropy alloy (HEA). The main objective was to investigate the microstructural development, phase stabilities and mechanical properties in relation to conventional manufacturing routes. Furthermore, thermodynamic calculations were used to explain the phase stabilities and solidification. L-PBF enables manufacturing of the ferritic stainless steels SS441 and SS446 with excellent mechanical properties. It was shown that solid particles may form in the melt and act as heterogeneous nucleation points, resulting in effective grain refinement for SS441. Other secondary phases can form during the thermal cycling in the L-PBF process, enhancing the mechanical properties. An example is the formation of austenite in SS446. Furthermore, the formation of solid particles and segregated microstructure during solidification was predicted by thermodynamic calculations.The AlCoCrFeNi alloy could be produced with an intriguing hierarchical microstructure and excellent mechanical properties using binder jetting and post-treatments. The microstructure of the final component can also be controlled by pre-annealing of the feedstock powder. Thermodynamic calculations were used to design the phase composition of the alloy. A characteristic single-phase solid solution is only observed at very high temperatures close to the melting point. Hence, the AlCoCrFeNi alloy is not a thermodynamically true HEA, but is stabilized due to kinetic effects during manufacturing.
  •  
32.
  • Karlsson, Dennis, et al. (author)
  • Additive manufacturing of the ferritic stainless steel SS441
  • 2020
  • In: Additive Manufacturing. - AMSTERDAM, NETHERLANDS : Elsevier BV. - 2214-8604 .- 2214-7810. ; 36
  • Journal article (peer-reviewed)abstract
    • In this study, the ferritic stainless steel SS441 was produced with excellent mechanical properties using laser powder bed fusion (L-PBF) compared to samples produced by conventional casting and hot-rolling. In addition, thermodynamic calculations were utilized to study the phase stability at elevated temperatures and to understand the solidification behavior. The hot-rolled sample showed a grain size up to several hundred mu m with additional precipitates of TiN and Nb(C,N). In contrast, the as-built L-PBF samples displayed a grain size in the mu m range. Spherical precipitates with a size of around 50 nm could be observed and were attributed to a corundum phase from the thermodynamic calculations. The printed material shows superior mechanical properties, with more than 30 times higher impact energy compared to the hot-rolled alloy (217 +/- 5 J vs. 7 +/- 0.5 J). Furthermore, the properties are anisotropic for the L-PBF produced alloy, with the highest tensile strength vertical to the build direction. The superior mechanical properties of the L-PBF produced sample can be attributed to a smaller grain size, giving a higher strength according to the Hall-Petch relationship. The anisotropy of the material can be eliminated by heat treatments at 900 degrees C followed by water quenching, but the absolute strength decreases slightly due to formation of intermetallic phases such as Nb(C,N) and the Fe2Nb Laves phase. The results clearly illustrates that L-PBF provides a promising manufacturing mute for enhanced strength of ferritic stainless steels.
  •  
33.
  • Karlsson, Dennis, et al. (author)
  • Binder jetting of the AlCoCrFeNi alloy
  • 2019
  • In: Additive Manufacturing. - : Elsevier. - 2214-8604 .- 2214-7810. ; 27, s. 72-79
  • Journal article (peer-reviewed)abstract
    • High density components of an AlCoCrFeNi alloy, often described as a high-entropy alloy, were manufactured by binder jetting followed by sintering. Thermodynamic calculations using the CALPHAD approach show that the high-entropy alloy is only stable as a single phase in a narrow temperature range below the melting point. At all other temperatures, the alloy will form a mixture of phases, including a sigma phase, which can strongly influence the mechanical properties. The phase stabilities in built AlCoCrFeNi components were investigated by comparing the as-sintered samples with the post-sintering annealed samples at temperatures between 900 °C and 1300 °C. The as-sintered material shows a dominant B2/bcc structure with additional fcc phase in the grain boundaries and sigma phase precipitating in the grain interior. Annealing experiments between 1000 °C and 1100 °C inhibit the sigma phase and only a B2/bcc phase with a fcc phase is observed. Increasing the temperature further suppresses the fcc phase in favor for the B2/bcc phases. The mechanical properties are, as expected, dependent on the annealing temperature, with the higher annealing temperature giving an increase in yield strength from 1203 MPa to 1461 MPa and fracture strength from 1996 MPa to 2272 MPa. This can be explained by a hierarchical microstructure with nano-sized precipitates at higher annealing temperatures. The results enlighten the importance of microstructure control, which can be utilized in order to tune the mechanical properties of these alloys. Furthermore, an excellent oxidation resistance was observed with oxide layers with a thickness of less than 5 μm after 20 h annealing at 1200 °C, which would be of great importance for industrial applications.
  •  
34.
  • Karlsson, Dennis, et al. (author)
  • Elemental segregation in an AlCoCrFeNi high-entropy alloy : A comparison between selective laser melting and induction melting
  • 2019
  • In: Journal of Alloys and Compounds. - : Elsevier BV. - 0925-8388 .- 1873-4669. ; 784, s. 195-203
  • Journal article (peer-reviewed)abstract
    • Additive manufacturing of a high-entropy alloy, AlCoCrFeNi, was studied with selective laser melting from gas atomized powder. A wide process parameter window in the SLM process was investigated but it was impossible to produce crack-free samples, attributed to stresses that originate during the building processes. The microstructure and elemental segregation in the SLM samples were compared with induction-melted AlCoCrFeNi. The induction-melted sample crystallizes in randomly oriented large grains (several hundred microns). Dendritic and inter-dendritic areas with slightly different chemical composition can be observed. Within these areas a spinodal decomposition occurs with a separation into FeCr- and NiAl-rich domains. Further spinodal decomposition within the FeCr-rich regions into Cr- and Fe-rich domains was observed by atom probe tomography.In contrast, the SLM-samples crystallizes in much smaller grains (less than 20 μm) with a dendrite-like substructure. These dendrite-like features exhibit distinct chemical fluctuations on the nm-scale. During annealing more pronounced chemical fluctuations and the formation of Cr-rich and Cr-poor regions can be observed. The difference in microstructure and spinodal decomposition between the induction-melted and SLM samples is attributed to the significantly higher cooling rate for SLM. This study shows that, by using different synthesis pathways, it is possible to modify the microstructure and segregation of element within alloys. This can be used to tune the materials properties, if the cracking behavior is handled e.g. by change of alloy composition to minimize phase transformations or use of a heating stage.
  •  
35.
  • Karlsson, Dennis, et al. (author)
  • Structure and Hydrogenation Properties of a HfNbTiVZr High-Entropy Alloy
  • 2018
  • In: Inorganic Chemistry. - : AMER CHEMICAL SOC. - 0020-1669 .- 1520-510X. ; 57:4, s. 2103-2110
  • Journal article (peer-reviewed)abstract
    • A high-entropy alloy (HEA) of HfNbTiVZr was synthesized using an arc furnace followed by ball milling. The hydrogen absorption mechanism was studied by in situ X-ray diffraction at different temperatures and by in situ and ex situ neutron diffraction experiments. The body centered cubic (BCC) metal phase undergoes a phase transformation to a body centered tetragonal (BCT) hydride phase with hydrogen occupying both tetrahedral and octahedral interstitial sites in the structure. Hydrogen cycling of the alloy at 500 degrees C is stable. The large lattice strain in the HEA seems favorable for absorption in both octahedral and tetrahedral sites. HEAs therefore have potential as hydrogen storage materials because of favorable absorption in all interstitial sites within the structure.
  •  
36.
  • Karlsson, Dennis, et al. (author)
  • Structure and phase transformations in gas atomized AlCoCrFeNi high entropy alloy powders
  • 2022
  • In: Journal of Alloys and Compounds. - : Elsevier BV. - 0925-8388 .- 1873-4669. ; 893
  • Journal article (peer-reviewed)abstract
    • In this study, the crystal structure and phase stability of gas atomized equiatomic AlCoCrFeNi powder was investigated. This alloy is usually described as a high entropy alloy forming a solid solution phase stabilized by a high mixing entropy. However, thermodynamic calculations show that the high entropy phase is stable only at very high temperatures close to the melting point and that a mixture of several phases are the most stable state at lower temperatures. This suggest that kinetic effects may influence the phase composition of atomized powder. The unique features of X-ray diffraction, neutron diffraction as well as transmission electron microscopy were used to study the atomic structure of the atomized powder in detail. The results show that the powder crystallises in an ordered B2 (CsCl-type) structure with a preferred site occupation of Al and Fe on the (1/2 1/2 1/2) position and Co and Ni on the (0 0 0) position. During heat-treatment of the powder, the B2 phase decomposes into fcc and sigma phases and the final phase composition is highly dependent on the heating rate. The effect of heat-treatment on the atomized powder was also investigated and revealed a significant phase transformation with e.g. the formation of sigma phase preferably at the surface of the powder particles. The phase content was also dependent on the size fraction of the powder particles. Sintering of green bodies made with different heat cycles showed that the phase composition of the starting material had a significant impact on the final phase composition and microstructure of the sintered components. The results illustrate the importance of well-defined powder materials for powder consolidation, especially additive manufacturing (binder jetting) of high entropy alloys.
  •  
37.
  • Kryshtal, O., et al. (author)
  • Microstructure and phase composition of the Ag-Al film wear track : Through-thickness characterization by advanced electron microscopy
  • 2019
  • In: Archives of Metallurgy and Materials. - : POLSKA AKAD NAUK, POLISH ACAD SCIENCES, INST METALL & MATER SCI PAS. - 1733-3490 .- 2300-1909. ; 64:1, s. 251-256
  • Journal article (peer-reviewed)abstract
    • Analytical transmission electron microscopy has been applied to characterize the microstructure, phase and chemical composition of the Ag-Al wear track throughout its thickness down to the atomic level. Microscopy findings have been correlated with Ag-Al film tribological properties to understand the effect of the hexagonal solid solution phase on the tribological properties of this film. Ag-25Al (at.%) films have been produced by simultaneous magnetron sputtering of components in Ar atmosphere under 1 mTorr pressure and subjected to pin-on-disc tribological tests. It has been shown that hcp phase with (001) planes aligned parallel to the film surface dominates both in as-deposited and in tribofilm areas of the Ag-Al alloy film. Possible mechanisms of reduced friction in easily oxidized Ag-Al system are discussed and the mechanism based on readily shearing basal planes of the hcp phase is considered as the most probable one.
  •  
38.
  • Lewin, Erik, et al. (author)
  • On the origin of a third spectral component of C1s XPS-spectra for nc-TiC/a-C nanocomposite thin films
  • 2008
  • In: Surface & Coatings Technology. - : Elsevier BV. - 0257-8972 .- 1879-3347. ; 202:15, s. 3563-3570
  • Journal article (peer-reviewed)abstract
    • X-ray photoelectron spectroscopy (XPS) spectra of sputter-etched nc-TiC/a-C nanocomposite thin films published in literature show an extra feature of unknown origin in the C1s region. This feature is situated between the contributions of carbide and the carbon matrix. We have used high kinetic energy XPS (HIKE-XPS) on magnetron-sputtered nc-TiC/a-C thin films to show that this feature represents a third chemical environment in the nanocomposites, besides the carbide and the amorphous carbon. Our results show that component is present in as-deposited samples, and that the intensity is strongly enhanced by Ar+-ion etching. This third chemical environment may be due to interface or disorder effects. The implications of these observations on the XPS analysis of nanocomposites are discussed in the light of overlap problems for ternary carbon based systems.
  •  
39.
  • Li, Wei, 1962-, et al. (author)
  • Foam cell death induced by 7β-hydroxycholesterol is mediated by labile iron-driven oxidative injury : Mechanisms underlying induction of ferritin in human atheroma
  • 2005
  • In: Free Radical Biology & Medicine. - : Elsevier BV. - 0891-5849 .- 1873-4596. ; 39:7, s. 864-875
  • Journal article (peer-reviewed)abstract
    • Human atherosclerotic lesions typically contain large amounts of ferritin associated with apoptotic macrophages and foam cells, although the reasons are unknown. In the present investigation, we studied the relationship between ferritin induction and occurrence of apoptosis in 7β-hydroxycholesterol (7β-OH)-treated monocytic cells and macrophages. We found that 7β-OH enlarges the intracellular labile iron pool, increases formation of reactive oxygen species (ROS), and induces ferritin and cytosolic accumulation of lipid droplets, lysosomal destabilization, and apoptototic macrophage death. Since ferritin is a phase II-type protective protein, our findings suggest that ferritin upregulation here worked as an inefficient defense mechanism. Addition to the culture medium of both a membrane-permeable iron chelator 10-phenanthroline and the non-membrane-permeable iron chelators apoferritin and desferrioxamine afforded significant protection against the 7β-OH-induced effects. Consequently, endocytosed iron compounds dramatically augmented 7β-OH-induced cytotoxicity. We conclude that oxidized lipid 7β-OH causes not only foam cell formation but also oxidative damage with abnormal metabolism of cellular iron. The findings suggest that modulation of iron metabolism in human atheroma may be a potential therapeutic strategy against atherosclerosis. © 2005 Elsevier Inc. All rights reserved.
  •  
40.
  •  
41.
  • Malinovskis, Paulius, et al. (author)
  • Synthesis and Characterisation of Nanocomposite Mo-Fe-B Thin Films Deposited by Magnetron Sputtering
  • 2021
  • In: Materials. - : MDPI. - 1996-1944. ; 14:7
  • Journal article (peer-reviewed)abstract
    • Several ternary phases are known in the Mo-Fe-B system. Previous ab initio calculations have predicted that they should exhibit a tempting mix of mechanical and magnetic properties. In this study, we have deposited Mo-Fe-B films with a Fe-content varying from 0-37 at.% using non-reactive DC (direct current) magnetron sputtering. The phase composition, microstructure, and mechanical properties were investigated using X-ray diffraction, scanning transmission electron microscopy, and nanoindentation measurements. Films deposited at 300 degrees C and with >7 at.% Fe are nanocomposites consisting of two amorphous phases: a metal-rich phase and a metal-deficient phase. Hardness and elastic modulus were reduced with increasing Fe-content from similar to 29 to similar to 19 GPa and similar to 526 to similar to 353 GPa, respectively. These values result in H-3/E-2 ratios of 0.089-0.052 GPa, thereby indicating brittle behaviour of the films. Also, no indication of crystalline ternary phases was observed at temperatures up to 600 degrees C, suggesting that higher temperatures are required for such films to form.
  •  
42.
  • Malinovskis, Paulius, et al. (author)
  • Synthesis and characterization of multicomponent (CrNbTaTiW)C films for increased hardness and corrosion resistance
  • 2018
  • In: Materials & design. - : Elsevier BV. - 0264-1275 .- 1873-4197. ; 149, s. 51-62
  • Journal article (peer-reviewed)abstract
    • Multicomponent carbide thin films of (CrNbTaTiW)C (30–40 at.% C) with different metal contents were depos-ited at different temperatures using non-reactive DC magnetron sputtering. The lattice distortion for the metallattice was estimated to vary from about 3 to 5%. Most films crystallized in the cubic B1 structure but Ta/W-rich films deposited at 600 °C exhibited a tetra gonal distortion. X-ray diffraction results sh ow that near-equimolar films exhibited a strong (111) texture. In contrast, Ta/W-rich films exhibited a shift from (111) to(100) texture at 450 °C. The in-plane relationship was determined to MC(111)[-12-1]//Al2O3(001)[110] with alattice mismatch of about 11% along the Al2O3[110] direction. A segregation of Cr to the grain boundaries was ob-served in all films. The microstructure was found to be the most important factor for high hardness. Less denseNb-rich and near-equimolar films deposited at low tem peratures exhib ited the low est hardnes s (12 GPa),while very dense Ta/W-rich high temperature films were found to be the hardest (36 GPa). No correlation wasfound between the lattice distortion and the hardness. Corrosion studies revealed that the multicomponentfilms exhibited excellent corrosion resistance, superior to that of a reference hyper-duplex stainless steel, in1.0 M HCl.
  •  
43.
  • Marattukalam, Jithin J., et al. (author)
  • Development of process parameters for selective laser melting of a Zr-based bulk metallic glass
  • 2020
  • In: Additive Manufacturing. - : Elsevier. - 2214-8604 .- 2214-7810. ; 33
  • Journal article (peer-reviewed)abstract
    • Parameters for selective laser melting of Zr59.3Cu28.8Al10.4Nb1.5 (trade name AMZ4), allowing crack-free bulk metallic glass with low porosity, have been developed. The phase formation was found to be strongly influenced by the heating power of the laser. X-ray amorphous samples were obtained with laser power at and below 75 W. The as-processed bulk metallic glass was found to devitrify by a two-stage crystallization process within which the presence of oxygen was concluded to play an essential role. At laser powers above 75 W, the observed crystallites were found to be a cubic phase (Cu2Zr4O). The hardness and Young’s modulus in the as-processed samples was found to increase marginally with increased fraction of the crystalline phase.
  •  
44.
  • Marattukalam, Jithin James (author)
  • Tailoring structure and morphology during additive manufacturing of metallic components
  • 2021
  • Doctoral thesis (other academic/artistic)abstract
    • The work described in this thesis explores the use of laser process parameters to functionalize the material properties by the control of microstructure and optimization of morphology in components by selective laser melting. The microstructure in amorphous and crystalline metallic alloy systems is influenced by changing the laser power density and scanning strategies respectively. A combination of X-ray/neutron diffraction and optical/electron microscopy is used to evaluate the microstructure and phase formation in SLM components. The influence of the microstructure on the mechanical properties of as-printed samples was investigated using hardness and uniaxial tensile testing methods. To begin with, the process parameters for selective laser melting of a Zr-based bulk metallic glass Zr59.3Cu28.8Al10.4Nb1.5 (trade name AMLOY-ZR01) are developed to obtain high density and crack-free bulk components. The influence of oxygen on the thermal stability and crystallization pathway in AMLOY-ZR01 was found to be significant in determining the formation of metastable crystalline phases within the amorphous matrix. It was also shown that the mechanical properties in AMLOY-ZR01 can be influenced by changing the amount of crystalline phases formed within the amorphous matrix.  This was achieved by changing the laser power density during the SLM process. The alloy composition was also investigated for its biocompatibility, and the cell-material interactions under in-vitro test conditions showed no cytotoxic effect. These findings demonstrate that AMLOY-ZR01 is a promising candidate for orthopedic bio-implant applications. The latter half of this work demonstrates the influence of microstructure and crystallographic texture on the mechanical properties of 316L SS. This was achieved by changing the "laser scanning methodology" during the SLM process and a correlation between the applied scanning methodology and structure-property relation was identified.  A single crystalline-like texture can be obtained using a bi-directional scanning methodology, whereas a fiber texture is achieved when rotating the laser scan vectors by 67° to melt consecutive powder bed layers. The mechanical properties of 316L SS are influenced by the type of laser scan used to fabricate the components, as it dictates the final grain orientation within the SLM samples. It is also shown that the scanning patterns can be altered during the SLM process to create position-specific crystallographic grain orientation within the component. This opens up the possibility to fabricate functionally graded components which contain a spatial variation in composition and/or microstructure for the specific purpose of controlling material properties. Finally, the functionalization of material properties through design of components by additive manufacturing was demonstrated by fabricating waveguides with the specific geometries.
  •  
45.
  • Marattukalam, Jithin James, et al. (author)
  • The effect of laser scanning strategies on texture, mechanical properties, and site-specific grain orientation in selective laser melted 316L SS
  • 2020
  • In: Materials & design. - : Elsevier BV. - 0264-1275 .- 1873-4197. ; 193
  • Journal article (peer-reviewed)abstract
    • Selective laser melting has been used to demonstrate the striking effect of laser scanning strategies on the crystalline texture in 316L SS. The aligned crystal orientation along the tensile direction (Z-axis) could be varied using the scanning strategy. A strong 〈100〉 single crystalline-like texture is obtained in the direction of the laser scan and a 〈110〉 texture was observed in the build direction when using a bidirectional scan without rotation. Fiber texture was observed along the tensile direction when the bi-directional laser scanning vectors were rotated by 67° (Rot-scan) for each layer. The study highlights a correlation between laser scanning strategies with resulting textures, microstructure, and mechanical properties in as-printed bulk 316L SS. The hardness, Young's modulus, and ultimate tensile strength were significantly influenced by the final microstructure, crystallographic texture, and porosity. Furthermore, the applied laser scanning strategies made it possible to tailor crystallographic textures locally within the component. This was demonstrated by printing characters with a fiber texture, in a matrix with ⟨100⟩ texture parallel to the Z-axis.
  •  
46.
  • Medina, León Zendejas, et al. (author)
  • Phase formation in magnetron sputtered CrMnFeCoNi high entropy alloy
  • 2020
  • In: Surface & Coatings Technology. - : Elsevier BV. - 0257-8972 .- 1879-3347. ; 403
  • Journal article (peer-reviewed)abstract
    • Thin films of the CrMnFeCoNi high entropy alloy were deposited by magnetron sputtering from a sintered equimolar target. The substrate temperature and bias were varied during deposition, and the structure, morphology and elemental distribution were studied in detail. All films formed phase mixtures of multiple crystal structures. This contrasts with studies on the bulk alloy, where it typically forms a single phase with a simple cubic closed packed (ccp) structure, with other phases precipitating only after long annealing times. For higher substrate temperatures, we observed a mixture of phases with ccp and bcc (body centered cubic) structures, and the intermetallic phases o-phase and L1(0), the first three being the predicted equilibrium phases at the deposition temperature. For room temperature depositions, we found evidence of very limited diffusion of metal atoms during the deposition. These films formed a mixture of a ccp and the intermetallic chi-phase. Two mechanisms can be distinguished that govern the phase formation at lower and higher temperatures. From the present results and comparisons with the literature, we also discuss why the small grain size, the low process temperature, and the fast surface diffusion during synthesis causes magnetron sputtering to yield different results compared to bulk synthesis from the melt. These principles explain why it is easier to form the equilibrium phases by sputtering, and why a single ccp phase should not be expected as a rule for this deposition method. Following the thermodynamic principles of high entropy alloys, this may also be the case in other high entropy alloy systems.
  •  
47.
  • Mockuté, Aurelija, et al. (author)
  • Synthesis and characterization of (Ti1-xAlx)B2+Delta thin films from combinatorial magnetron sputtering
  • 2019
  • In: Thin Solid Films. - : ELSEVIER SCIENCE SA. - 0040-6090 .- 1879-2731. ; 669, s. 181-187
  • Journal article (peer-reviewed)abstract
    • (Ti1-xAlx)B2+Delta films with a lateral composition gradient of x = [0.30-0.66] and Delta = [0.07-1.22] were deposited on an Al2O3 wafer by dual magnetron sputtering at 400 degrees C from sintered TiB2 and AlB2 targets. Composition analysis indicates that higher Ti:Al ratios favor overstoichiometry in B and a reduced incorporation of O. Transmission electron microscopy reveals distinctly different microstructures of Ti- and Al-rich compositions, with formation of characteristic conical growth features for the latter along with a lower degree of crystallinity and significantly less tissue phase from B segregation at the grain boundaries. For Al-rich films, phase separation into Ti- and Al-rich diboride nanometer-size domains is observed and interpreted as surface-initiated spinodal decomposition. The hardness of the films ranges from 14 to 28 GPa, where the higher values were obtained for the Ti-rich regions of the metal boride.
  •  
48.
  • Moro, Marcos V., et al. (author)
  • Accurate high-resolution depth profiling of magnetron sputtered transition metal alloy films containing light species : A multi-method approach
  • 2019
  • In: Thin Solid Films. - : Elsevier BV. - 0040-6090 .- 1879-2731. ; 686
  • Journal article (peer-reviewed)abstract
    • We present an assessment of a multi-method approach based on ion beam analysis to obtain high-resolution depth profiles of the total chemical composition of complex alloy systems. As a model system we employ an alloy based on several transition metals and containing light species. Samples have been investigated by a number of different ion-beam based techniques, i.e., Rutherford Backscattering Spectrometry, Particle-Induced X-ray Emission, Elastic Backscattering Spectrometry and Time-of-Flight/Energy Elastic Recoil Detection Analysis. Sets of spectra obtained from these different techniques were analyzed both independently and following an iterative and self-consistent approach yielding a more accurate depth profile of the sample, including both metallic heavy constituents (Cr, Fe and Ni) as well as the rather reactive light species (C, O) in the alloy. A quantitative comparison in terms of achievable precision and accuracy is made and the limitations of the single method approach are discussed for the different techniques. The multi-method approach is shown to yield significantly improved and accurate information on stoichiometry, depth distribution and thickness of the alloy with the improvements being decisive for a detailed correlation of composition to the material properties such as corrosion strength. The study also shows the increased relative importance of experimental statistics for the achievable accuracy in the multi-method approach.
  •  
49.
  • Mukhamedov, Boburjon, et al. (author)
  • Tetragonal distortion in magnetron sputtered bcc-W films with supersaturated carbon
  • 2022
  • In: Materials & design. - : Elsevier Science Ltd. - 0264-1275 .- 1873-4197. ; 214
  • Journal article (peer-reviewed)abstract
    • Carbon has a low solid solubility in bcc tungsten at equilibrium. However, metastable supersaturated solid solutions can be synthesized with magnetron sputtering. Here, we present a systematic study on the phase stability and mechanical properties of such supersaturated W-C solid solutions. H-2h scans show a split of the 200/020 and the 002 peaks for supersaturated films which is explained by a tetragonal distortion of the bcc structure. This split increases with increasing C content and is maximized at 4 at.% C, where we observe an a/b axis of 3.15-3.16 A and a c-axis of 3.21-3.22 A. We performed first-principles calculations of lattice parameters, mixing enthalpies, elastic constants and polycrystalline elastic moduli for cubic and tetragonal W-C solid solutions. Calculations show that tetragonal structure is more stable than the bcc supersaturated solid solution and the calculated lattice parameters and Youngs moduli follow the same trends as the experimental ones as a function of C concentration. The results suggest that supersaturated films with lattice distortion can be used as a design approach to improve the properties of transition metal films with a bcc structure. (c) 2022 The Authors. Published by Elsevier Ltd.
  •  
50.
  • Osinger, Barbara, 1995- (author)
  • Investigation of compositionally complex refractory metal based thin films
  • 2024
  • Doctoral thesis (other academic/artistic)abstract
    • The search for new and improved materials has led to the discovery and establishment of compositionally complex or high-entropy materials. The work in this thesis is focused on the investigation of new compositionally complex materials based on the refractory metals of groups 4-6. The materials in this work were synthesised using non-reactive dc magnetron sputtering and three material systems have been studied: HfNbTiVZr-C, CrTiTaWNb-C and Nb-Mo-C. In the context of compositionally complex materials, this thesis aims to contribute specifically to questions regarding (i) the prediction of phase formation and stability (ii) the chemical interaction between atoms (iii) the correlation between the material properties and compositional complexity. The prediction of phase formation and stability using calculated phase diagram (CALPHAD) methods was studied in the HfNbTiVZr-C system. The findings suggest that CALPHAD methods are promising predictive tools, although kinetic effects during synthesis need to be taken into consideration. Furthermore, theoretical, and experimental evidence of charge transfer effects was demonstrated within the HfNbTiVZr-C system. The results of ab initio materials simulations and X-ray Photoelectron Spectroscopy (XPS) measurements highlight the importance of understanding and considering the local chemical environment and chemical interactions in compositionally complex materials.The approach of metal alloying according to the valence electron concentration (VEC) to tune the mechanical properties was studied in the Nb-Mo-C system. The findings show the importance of microstructural effects on the mechanical properties in the studied thin film materials, which can overshadow the compositional or VEC variations. The response to Xe heavy-ion irradiation was studied in the CrTiTaWNb-C system using in situ irradiation experiments. This work presents a comparison between three different compositions: a TaW-rich alloy and carbide thin film as well as a near-equimolar carbide film. The findings indicate that both microstructure and chemical homogeneity play important roles when it comes to radiation damage tolerance in compositional complex materials.This thesis demonstrates the elaborate and multifaceted nature of compositionally complex materials. Whether it comes to the fundamental understanding or the effective implementation of a materials design tool, many factors need to be taken into consideration, including chemical interactions between the constituent elements and microstructural effects.
  •  
Skapa referenser, mejla, bekava och länka
  • Result 1-50 of 73
Type of publication
journal article (56)
doctoral thesis (8)
other publication (3)
conference paper (3)
editorial collection (1)
research review (1)
show more...
licentiate thesis (1)
show less...
Type of content
peer-reviewed (58)
other academic/artistic (15)
Author/Editor
Jansson, Ulf, 1960- (56)
Lewin, Erik, Dr. 197 ... (16)
Sahlberg, Martin, 19 ... (14)
Riekehr, Lars (12)
Berastegui, Pedro (8)
Osinger, Barbara (8)
show more...
Hjörvarsson, Björgvi ... (7)
Nyholm, Leif, 1961- (7)
Hultman, Lars, 1960- (6)
Jansson, Ulf (6)
Taher, Mamoun (6)
Cedervall, Johan (6)
Malinovskis, Paulius (6)
Lindwall, Greta (5)
Lindblad, Rebecka, D ... (5)
Alling, Björn (4)
Abrikosov, Igor (4)
Schneider, Jochen M. (4)
Tylén, Ulf, 1938 (4)
Donzel-Gargand, Oliv ... (4)
Bake, Björn, 1939 (4)
Ekberg-Jansson, Ann, ... (4)
Mao, Fang (4)
Hans, Marcus (3)
Gamstedt, E. Kristof ... (3)
Wilhelmsson, Ola (3)
Andersson, Anna M (3)
Vikgren, Jenny, 1957 (3)
von Fieandt, Linus (3)
Ek, Gustav (3)
Andersson, Joakim (2)
Primetzhofer, Daniel (2)
Dancila, Dragos (2)
Thuvander, Mattias, ... (2)
Palisaitis, Justinas (2)
Hjörvarsson, Björgvi ... (2)
Rydberg, Anders (2)
Ström, Petter (2)
Kádas, Krisztina (2)
Persson, Per O A (2)
Holländer Pettersson ... (2)
Johansson, Niklas (2)
Larsson, Sven, 1943 (2)
Boijsen, Marianne, 1 ... (2)
Casillas Trujillo, L ... (2)
Odqvist, Joakim (2)
Tavares da Costa, Ma ... (2)
Schuisky, Mikael (2)
Harlin, Peter (2)
Iusan, Diana (2)
show less...
University
Uppsala University (64)
Linköping University (14)
Royal Institute of Technology (8)
University of Gothenburg (6)
Luleå University of Technology (2)
Stockholm University (2)
show more...
Chalmers University of Technology (2)
Karlstad University (2)
Lund University (1)
show less...
Language
English (71)
Swedish (2)
Research subject (UKÄ/SCB)
Natural sciences (48)
Engineering and Technology (23)
Medical and Health Sciences (5)
Social Sciences (1)
Humanities (1)

Year

Kungliga biblioteket hanterar dina personuppgifter i enlighet med EU:s dataskyddsförordning (2018), GDPR. Läs mer om hur det funkar här.
Så här hanterar KB dina uppgifter vid användning av denna tjänst.

 
pil uppåt Close

Copy and save the link in order to return to this view