1. |
|
|
2. |
- Okda, Sherif, et al.
(author)
-
Testing of the Aerodynamic Characteristics of an Inflatable Airfoil Section
- 2020
-
In: Journal of Aerospace Engineering. - 1943-5525 .- 0893-1321. ; 33:5
-
Journal article (peer-reviewed)abstract
- Inflatable structures are characterized by being light and easy to manufacture and deploy. Hence, they find many applications in aerospace and aeronautical engineering. In this paper, an inflatable segment with a The National Advisory Committee for Aeronautics (NACA) 0021 airfoil cross-section is designed, fabricated, and tested. The geometrical accuracy of the manufactured inflatable segment is measured using laser scanning. Measurements show that the average normalized error of the chord length and thickness are 2.97% and 0.554%, respectively. The aerodynamic behavior of the inflatable segment is then tested in a wind tunnel at different wind speeds and angles of attack. Lift forces are measured using a six-component balance, while the drag forces are calculated from the wake measurements. The lift and drag coefficients of the inflatable section are compared to those of a standard NACA 0021 airfoil. Finally, flow visualization is examined at different angles of attack using two methods: smoke and tufts. Both methods show that flow separation starts at 15° and full stall occurs at 25°. Results indicate that inflatables can find more applications in the design and construction of aerodynamic structures, such as wings.
|
|
3. |
|
|
4. |
-
INNOTRACK: Concluding technical report
- 2010
-
Editorial collection (peer-reviewed)abstract
- The track structure, rails, switches and crossings account for more than 50% of maintenance and renewal costs for the rail industry. To improve the competitiveness of rail transportation, the cost-efficiency of these areas needs to be addressed.This the background to INNOTRACK, an integrated research project funded by the European Commission’s 6th research framework pro- gramme. Running from September 2006 to December 2009, INN- OTRACK has developed a multitude of innovative solutions in the areas of track substructure, rails & welds, and switches & crossings. The solutions have been assessed from technical, logistics and life cycle cost point of views.This Concluding Technical Report of INNOTRACK includes an overview of the project. It further details implementable results, and clusters them into ”highlight” areas. In addition, the book acts as a ”key” to the vast amount of information from INNOTRACK: All sections refer to project reports where more information can be found.
|
|
5. |
|
|
6. |
- Heshmati, Mohsen, 1987, et al.
(author)
-
Dependency of cohesive laws of a structural adhesive in Mode-I and Mode-II loading on moisture, freeze-thaw cycling, and their synergy
- 2017
-
In: Materials and Design. - : Elsevier BV. - 1873-4197 .- 0264-1275. ; 122, s. 433-447
-
Journal article (peer-reviewed)abstract
- In recent years, adhesive bonding has found its way to construction applications such as bridges. Given the harsh conditions that such structures are usually exposed to, it is necessary to account for environmental factors, particularly moisture and temperature, in the design phase. Cohesive zone modelling has attracted much attention in the last decade as a promising method to design adhesive joints. Despite this interest, the effects of moisture and thermal cycles on cohesive laws have not been investigated to the knowledge of the authors. In this paper, we present a method to directly measure the environmental-dependent cohesive laws of a structural adhesive loaded in pure Mode-I and Mode-II. Special consideration is given to overcome issues such as the time-consuming nature of moisture ingression and specimen dimensions, which could be problematic due to the size-limitations of conditioning equipment. The accuracy of this method was verified through simulation of the experiments using the finite element analysis. The effects of exposure to 95% relative humidity, immersion in saltwater and distilled water, and freeze-thaw cycles in the presence or absence of moisture were investigated. The results indicate the damaging effects of combined saltwater and freeze-thaw cycles which were clearly reflected on the shape of the cohesive laws.
|
|
7. |
|
|
8. |
- Stylidis, Kostas, 1978, et al.
(author)
-
Perceived quality framework in product generation engineering: an automotive industry example
- 2019
-
In: Design Science. - : Cambridge University Press (CUP). - 2053-4701 .- 2053-4701. ; 5
-
Journal article (peer-reviewed)abstract
- Perceived quality refers to customers’ cognitive and emotional responses to a particular design, often also associated with craftsmanship and customer satisfaction. Previous research defined a taxonomy of perceived quality and provided understanding about how engineering design decisions impact customer satisfaction. Furthermore, development of new products is frequently based on carrying over attributes of existing products, either from the same producer or from competitors. Previous research offered a new product development methodology combining variations of subsystems to carry over from existing products. This brief presents how these two lines of research combined to design the central console of the Porsche Panamera automobile and discusses the opportunities and challenges posed in the practical implementation of this research.
|
|
9. |
- Eriksson, Sören, 1953-
(author)
-
China's aircraft industry: collaboration and technology transfer - the case of Airbus
- 2010
-
In: International Journal of Technology Transfer and Commercialisation (IJTTC). - : Inderscience Enterprises Ltd. - 1470-6075 .- 1741-5284. ; 9:4, s. 306-325
-
Journal article (peer-reviewed)abstract
- China has moved a long way in economic and industrial development during the last decades and has developed into a global player in many industries. With increased knowledge in high-technology industries, China has ambitions to move into sectors that necessitate a high level of research and development, such as the aerospace industry. China is now in the process of establishing a modern aircraft industry based on domestic efforts as well as agreements with foreign partners in the manufacturing of complete aircraft. This paper analyzes what measures have been taken by Airbus in the form of technology transfer and other supportive measures to strengthen its position in the Chinese market. The findings conclude that Airbus’ transfer should be looked upon as a broad spectrum of technology and knowledge transfer, which include aircraft manufacturing technology, as well as cabin crew training centre, establishment of a warehouse and suppliers ”village”, an engineering centre, maintenance and various service functions.
|
|
10. |
- Wadekar, Sandip, 1989
(author)
-
Large-Eddy Simulation of Gasoline Fuel Spray Injection at Ultra-High Injection Pressures
- 2021
-
Doctoral thesis (other academic/artistic)abstract
- Gasoline direct injection is a state-of-the-art technique that reduces hydrocarbon and particulate emissions. However, further improvement is needed to meet current as well as future emission regulations. A prominent solution is to increase the fuel injection pressure which allows faster fuel droplet atomization, quick evaporation and improves fuel-air mixture formation under realistic engine conditions. In this work, the gasoline fuel injection process at ultra-high injection pressures ranging from 200 to 1500 bar was analyzed using numerical models. In particular, the Large-Eddy Simulation (LES) method, with the standard Smagorinsky turbulence model, was utilized using the Eulerian formulation for the continuous phase. The discrete droplet phase was treated using a Lagrangian formulation together with spray sub-models. In the first part of study, spray was injected into an initially quiescent constant volume chamber using two different nozzle hole shape geometries: divergent and convergent. The numerical results were calibrated by reproducing experimentally observed liquid penetration length and efforts were made to understand the influence of ultra-high injection pressures on spray development. The calibrated models were then used to investigate the impact of ultra-high injection pressures on mean droplet sizes, droplet size distribution, spray-induced large-scale eddies and entrainment rate. The results showed that, at ultra-high injection pressures, the mean droplet sizes were significantly reduced and the droplets achieving very high velocities. Integral length scales of spray-induced turbulence and air entrainment rate were better for the divergent-shaped injector, and considerably larger at higher injection pressures compared to lower ones. In the second part of the study, four consecutive full-cycle cold flow LES simulations were carried out to generate realistic turbulence inside the engine cylinder. The first three cycles were ignored, with the fourth cycle being used to model the injection of the fuel using the divergent-shaped injector only (which was found to be better in the previous part of this study) at different injection pressures. In addition to the continuous gas phase (Eulerian) and the dispersed liquid (Lagrangian), the liquid film feature (Finite-Area) was used to model the impingement of fuel spray on the engine walls and subsequent liquid film formation. The simulation results were used to evaluate spray-induced turbulence, fuel-air mixing efficiency and the amount of liquid mass deposited on the walls. The limitation of the high-pressure injection technique with respect to liquid film formation was optimized using a start of injection (SOI) sweep. Overall results showed that the mixing efficiency increased at high injection pressure and that SOI should occur between early injection and late injection to optimize the amount of mass being deposited on the engine walls.
|
|
11. |
- Liu, Yuanhua, 1971, et al.
(author)
-
Considering the importance of user profiles in interface design
- 2009
-
In: User Interfaces. ; , s. 23-
-
Book chapter (other academic/artistic)abstract
- User profile is a popular term widely employed during product design processes by industrial companies. Such a profile is normally intended to represent real users of a product. The ultimate purpose of a user profile is actually to help designers to recognize or learn about the real user by presenting them with a description of a real user’s attributes, for instance; the user’s gender, age, educational level, attitude, technical needs and skill level. The aim of this chapter is to provide information on the current knowledge and research about user profile issues, as well as to emphasize the importance of considering these issues in interface design. In this chapter, we mainly focus on how users’ difference in expertise affects their performance or activity in various interaction contexts. Considering the complex interaction situations in practice, novice and expert users’ interactions with medical user interfaces of different technical complexity will be analyzed as examples: one focuses on novice and expert users’ difference when interacting with simple medical interfaces, and the other focuses on differences when interacting with complex medical interfaces. Four issues will be analyzed and discussed: (1) how novice and expert users differ in terms of performance during the interaction; (2) how novice and expert users differ in the perspective of cognitive mental models during the interaction; (3) how novice and expert users should be defined in practice; and (4) what are the main differences between novice and expert users’ implications for interface design. Besides describing the effect of users’ expertise difference during the interface design process, we will also pinpoint some potential problems for the research on interface design, as well as some future challenges that academic researchers and industrial engineers should face in practice.
|
|
12. |
- Nybacka, Mikael, et al.
(author)
-
Project: CASTT - Centre for Automotive Systems Technologies and Testing
- 2007
-
Other publication (pop. science, debate, etc.)abstract
- Through the Centre for Automotive Systems Technologies and Testing, Luleå University of Technology aims to first of all support automotive winter testing in Northern Sweden. This means to support the local automotive test entrepreneurs and through them their customers: the car manufacturers and their suppliers. To succeed in this task, the center relies on the university's areas of leading research and most importantly on the cooperation between those areas.
|
|
13. |
- Skagestad, Ragnhild, 1978, et al.
(author)
-
GCCSI Webinar: Cutting Cost of CO2 Capture in Process Industry (CO2stCap) Project overview & first results for partial CO2 capture at integrated steelworks
- 2017
-
Other publication (other academic/artistic)abstract
- GCCSI Webinar: Cutting Cost of CO2 Capture in Process Industry (CO2stCap) Project overview & first results for partial CO2 capture at integrated steelworks This publication has the format of a webinar: The CO2StCap project is a four year initiative carried out by industry and academic partners with the aim of reducing capture costs from CO2 intensive industries (more information here). The project, led by Tel-Tek, is based on the idea that cost reduction is possible by capturing only a share of the CO2 emissions from a given facility, instead of striving for maximized capture rates. This can be done in multiple ways, for instance by capturing only from the largest CO2 sources at individual multi-stack sites utilising cheap waste heat or adapting the capture volumes to seasonal changes in operations. The main focus of this research is to perform techno-economic analyses for multiple partial CO2 capture concepts in order to identify economic optimums between cost and volumes captured. In total for four different case studies are developed for cement, iron & steel, pulp & paper and ferroalloys industries. The first part of the webinar gave an overview of the project with insights into the cost estimation method used. The second part presented the iron & steel industry case study based on the Lulea site in Sweden, for which waste-heat mapping methodology has been used to assess the potential for partial capture via MEA-absorption. Capture costs for different CO2 sources were discussed, demonstrating the viability of partial capture in an integrated steelworks.
|
|
14. |
- Kyprianidis, Konstantinos, 1984, et al.
(author)
-
Multidisciplinary Analysis of a Geared Fan Intercooled Core Aero-Engine
- 2014
-
In: Journal of Engineering for Gas Turbines and Power. - : ASME International. - 1528-8919 .- 0742-4795. ; 136:1
-
Journal article (peer-reviewed)abstract
- The reduction of CO2 emissions is strongly linked with the improvement of engine specific fuel consumption, along with the reduction of engine nacelle drag and weight. One alternative design approach to improving specific fuel consumption is to consider a geared fan combined with an increased overall pressure ratio intercooled core performance cycle. The thermal benefits from intercooling have been well documented in the literature. Nevertheless, there is very little information available in the public domain with respect to design space exploration of such an engine concept when combined with a geared fan. The present work uses a multidisciplinary conceptual design tool to analyze the option of an intercooled core geared fan aero engine for long haul applications with a 2020 entry into service technology level assumption. With minimum mission fuel in mind, the results indicate as optimal values a pressure ratio split exponent of 0.38 and an intercooler mass flow ratio of 1.18 at hot-day top of climb conditions. At ISA midcruise conditions a specific thrust of 86 m/s, a jet velocity ratio of 0.83, an intercooler effectiveness of 56%, and an overall pressure ratio value of 76 are likely to be a good choice. A 70,000 lbf intercooled turbofan engine is large enough to make efficient use of an all-axial compression system, particularly within a geared fan configuration, but intercooling is perhaps more likely to be applied to even larger engines. The proposed optimal jet velocity ratio is actually higher than the value one would expect by using standard analytical expressions, primarily because this design variable affects core efficiency at midcruise due to a combination of several different subtle changes to the core cycle and core component efficiencies at this condition. The analytical expressions do not consider changes in core efficiency and the beneficial effect of intercooling on transfer efficiency, nor do they account for losses in the bypass duct and jet pipe, while a relatively detailed engine performance model, such as the one utilized in this study, does. Mission fuel results from a surrogate model are in good agreement with the results obtained from a rubberized-wing aircraft model for some of the design parameters. This indicates that it is possible to replace an aircraft model with specific fuel consumption and weight penalty exchange rates. Nevertheless, drag count exchange rates have to be utilized to properly assess changes in mission fuel for those design parameters that affect nacelle diameter.
|
|
15. |
- Mathern, Alexandre, 1986, et al.
(author)
-
Concrete Support Structures for Offshore Wind Turbines: Current Status, Challenges, and Future Trends
- 2021
-
In: Energies. - : MDPI AG. - 1996-1073 .- 1996-1073. ; 14:7
-
Research review (peer-reviewed)abstract
- Today’s offshore wind turbine support structures market is largely dominated by steel structures, since steel monopiles account for the vast majority of installations in the last decade and new types of multi-leg steel structures have been developed in recent years. However, as wind turbines become bigger, and potential sites for offshore wind farms are located in ever deeper waters and ever further from the shore, the conditions for the design, transport, and installation of support structures are changing. In light of these facts, this paper identifies and categorizes the challenges and future trends related to the use of concrete for support structures of future offshore wind projects. To do so, recent advances and technologies still under development for both bottom-fixed and floating concrete support structures have been reviewed. It was found that these new developments meet the challenges associated with the use of concrete support structures, as they will allow the production costs to be lowered and transport and installation to be facilitated. New technologies for concrete support structures used at medium and great water depths are also being developed and are expected to become more common in future offshore wind installations. Therefore, the new developments identified in this paper show the likelihood of an increase in the use of concrete support structures in future offshore wind farms. These developments also indicate that the complexity of future support structures will increase due to the development of hybrid structures combining steel and concrete. These evolutions call for new knowledge and technical know-how in order to allow reliable structures to be built and risk-free offshore installation to be executed.
|
|
16. |
- Mirkhalaf, S. Mohsen, 1982, et al.
(author)
-
A finite element based orientation averaging method for predicting elastic properties of short fiber reinforced composites
- 2020
-
In: Composites Part B-Engineering. - : Elsevier BV. - 1359-8368. ; 202
-
Journal article (peer-reviewed)abstract
- Short fiber reinforced composites have a variety of micro-structural parameters that affect their macromechanical performance. A modeling methodology, capable of accommodating a broad range of these parameters, is desirable. This paper describes a micro-mechanical model which is developed using Finite Element Analysis and Orientation Averaging. The model is applicable to short fiber reinforced composites with a wide variety of micro-structural parameters such as arbitrary fiber volume fractions, fiber aspect ratios and fiber orientation distributions. In addition to the Voigt and Reuss assumptions, an interaction model is developed based on the self-consistent assumption. Comparisons with experimental results, and direct numerical simulations of Representative Volume Elements show the capability of the model for fair predictions.
|
|
17. |
- Esmaeili, Ali, 1983, et al.
(author)
-
Modelling of temperature and strain rate dependent behaviour of pearlitic steel in block braked railway wheels
- 2021
-
In: Railway Engineering Science. - : Springer. - 2662-4745 .- 2662-4753. ; 29:4, s. 362-378
-
Journal article (peer-reviewed)abstract
- Block braked railway wheels are subjected to thermal and rolling contact loading. The thermal loading results in high temperatures and thermal stresses which cause slow time dependent processes such as creep, relaxation and static recovery of the wheel material. At the same time, the rolling contact loading implies a very fast mechanical load application. This paper is focused on material modeling of pearlitic steel for a wide range of loading rates at elevated temperatures. The starting point is a viscoplasticity model including nonlinear isotropic and kinematic hardening. The Delobelle overstress function is employed to capture strain rate dependent response of the material. The model also includes static recovery of the hardening to capture slower viscous (diffusion dominated) behaviour of the material. Experiments for the pearlitic wheel steel ER7 in terms of cyclic strain-controlled uniaxial tests with hold-time, uniaxial ratchetting tests including rapid cycles and biaxial cyclic tests with tension/compression and torsion are used to calibrate the material model. These experiments were performed under isothermal conditions at different temperatures. In the ratchetting tests, higher loading rates are obtained and these have been used to calibrate the high strain rate response of the viscoplasticity model. The paper is concluded with a numerical example of a block braked wheel where the importance of accounting for the viscoplasticity in modelling is highlighted.
|
|
18. |
- Shahroozi, Zahra, 1992-
(author)
-
Survivability control using data-driven approaches and reliability analysis for wave energy converters
- 2024
-
Doctoral thesis (other academic/artistic)abstract
- Wave energy, with five times the energy density of wind and ten times the power density of solar, offers a compelling carbon-free electricity solution. Despite its advantages, ongoing debates surround the reliability and economic feasibility of wave energy converters (WECs). To address these challenges, this doctoral thesis is divided into four integral parts, focusing on optimizing the prediction horizon for power maximization, analyzing extreme waves' impact on system dynamics, ensuring reliability, and enhancing survivability in WECs.Part I emphasizes the critical importance of the prediction horizon for maximal power absorption in wave energy conversion. Using generic body shapes and modes, it explores the effect of dissipative losses, noise, filtering, amplitude constraints, and real-world wave parameters on the prediction horizon. Findings suggest achieving optimal power output may be possible with a relatively short prediction horizon, challenging traditional assumptions.Part II shifts focus to WEC system dynamics, analyzing extreme load scenarios. Based on a 1:30 scaled wave tank experiment, it establishes a robust experimental foundation, extending into numerical assessment of the WEC. Results underscore the importance of damping to alleviate peak forces. Investigating various wave representations highlights conservative characteristics of irregular waves, crucial for WEC design in extreme sea conditions.Part III explores the computational intricacies of environmental design load cases and fatigue analyses for critical mechanical components of the WEC. The analysis is conducted for hourly sea state damage and equivalent two-million-cycle loads. Finally, a comparison of safety factors between the ultimate limit state and fatigue limit state unfolds, illustrating the predominant influence of the ultimate limit state on point-absorber WEC design.Part IV, centers on elevating survivability strategies for WECs in extreme wave conditions. Three distinct controller system approaches leverage neural networks to predict and minimize the line force. Distinct variations emerge in each approach, spanning from rapid detection of optimal damping to integrating advanced neural network architectures into the control system with feedback. The incorporation of a controller system, refined through experimental data, showcases decreases in the line force, providing a practical mechanism for real-time force alleviation.This thesis aims to contribute uniquely to the goal of advancing wave energy conversion technology through extensive exploration.
|
|
19. |
- Binder, Christian, 1988-, et al.
(author)
-
Phosphor Thermometry for In-Cylinder Surface Temperature Measurements in Diesel Engines
- 2019
-
In: Measurement science and technology. - 0957-0233 .- 1361-6501.
-
Journal article (other academic/artistic)abstract
- Surface temperature measurements in technically relevant applications can be very hallenging and yet of great importance. Phosphor thermometry is a temperature measurement technique that has previously been employed in technically relevant applications to obtain surface temperature. The technique is based on temperature-dependent changes in a phosphor’s luminescence. To improve the accuracy and precision of temperature measurements with this technique, the present study considers, by way of example, the impact of conditions inside the cylinder of a diesel engine on decay time based phosphor thermometry. After an initial, general assessment of the effect of prevailing measurement conditions, this research investigates errors caused by soot luminosity, extinction, signal trapping and changes of phosphors’ luminescence properties due to exposure to the harsh environment. Furthermore, preferable properties of phosphors which are suitable for in-cylinder temperature measurements are discussed. 16 phosphors are evaluated, including four which – to the authors’ knowledge –have previously not been used in thermometry. Results indicate that errors due to photocathode bleaching, extinction, signal trapping and changes of luminescence properties may cause an erroneous temperature evaluation with temperature errors in the order of serval tens of Kelvin.
|
|
20. |
- Yang, Shun-Han, 1987, et al.
(author)
-
Parametric study of the dynamic motions and mechanical characteristics of power cables for wave energy converters
- 2018
-
In: Journal of Marine Science and Technology. - : Springer Science and Business Media LLC. - 0948-4280 .- 1437-8213. ; 23:1, s. 10-29
-
Journal article (peer-reviewed)abstract
- A case study of a point-absorber wave energy converter (WEC) system is presented. The WEC system forms an array, with several WECs located around a central hub to which they are each connected by a short, free-hanging power cable. The objective of the study is to analyse the dynamic characteristics and estimate the fatigue life of the power cable which is not yet in use or available on the commercial market. Hence, a novel approach is adopted in the study considering that the power cable’s length is restricted by several factors (e.g., the clearances between the service vessel and seabed and the cable), and the cable is subject to motion and loading from the WEC and to environmental loads from waves and currents (i.e., dynamic cable). The power cable’s characteristics are assessed using a numerical model subjected to a parametric analysis, in which the environmental parameters and the cable’s design parameters are varied. The results of the numerical simulations are compared and discussed regarding the responses of the power cables, including dynamic motion, curvature, cross-sectional forces, and accumulated fatigue damage. The effects of environmental conditions on the long-term mechanical life spans of the power cables are also investigated. Important cable design parameters that result in a long power cable (fatigue) service life are identified, and the cable service life is predicted. This study contributes a methodology for the first-principle design of WEC cables that enables the prediction of cable fatigue life by considering environmental conditions and variations in cable design parameters.
|
|
21. |
- Chen, Zhe, et al.
(author)
-
Nano-scale characterization of white layer in broached Inconel 718
- 2017
-
In: Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. - Amsterdam : Elsevier BV. - 0921-5093 .- 1873-4936. ; 684, s. 373-384
-
Journal article (peer-reviewed)abstract
- The formation mechanism of white layers during broaching and their mechanical properties are not well investigated and understood to date. In the present study, multiple advanced characterization techniques with nano-scale resolution, including transmission electron microscopy (TEM), transmission Kikuchi diffraction (TKD), atom probe tomography (APT) as well as nano-indentation, have been used to systematically examine the microstructural evolution and corresponding mechanical properties of a surface white layer formed when broaching the nickel-based superalloy Inconel 718.TEM observations showed that the broached white layer consists of nano-sized grains, mostly in the range of 20–50 nm. The crystallographic texture detected by TKD further revealed that the refined microstructure is primarily caused by strong shear deformation. Co-located Al-rich and Nb-rich fine clusters have been identified by APT, which are most likely to be γ′ and γ′′ clusters in a form of co-precipitates, where the clusters showed elongated and aligned appearance associated with the severe shearing history. The microstructural characteristics and crystallography of the broached white layer suggest that it was essentially formed by adiabatic shear localization in which the dominant metallurgical process is rotational dynamic recrystallization based on mechanically-driven subgrain rotations. The grain refinement within the white layer led to an increase of the surface nano-hardness by 14% and a reduction in elastic modulus by nearly 10% compared to that of the bulk material. This is primarily due to the greatly increased volume fraction of grain boundaries, when the grain size was reduced down to the nanoscale.
|
|
22. |
- Vernersson, Tore V, 1968, et al.
(author)
-
Wear of brake blocks for in-service conditions-Influence of the level of modelling
- 2014
-
In: Wear. - : Elsevier BV. - 0043-1648. ; 314:1-2, s. 125-131
-
Journal article (peer-reviewed)abstract
- Wear of brake blocks at tread braking of railway wheels is one of the key factors that control the time period between scheduled train maintenance and hence has a substantial impact on the life cycle cost of the vehicle. Wear simulations using two different numerical models, one thermal model and one thermoelastic model, are presented implementing wear rates for some brake block materials exploiting results from previously performed temperature-controlled pin-on-disc tests. It is found that the thermal model and the thermoelastic model give the same wear for cases when thermoelastic instability effects are small. However, for cases when the thermoelastic effects increase the local contact pressures and surface temperatures, large differences are found.
|
|
23. |
- Midya, Surajit, et al.
(author)
-
DC Component From Pantograph Arcing in AC Traction System : Influencing Parameters, Impact, and Mitigation Techniques
- 2011
-
In: IEEE transactions on electromagnetic compatibility (Print). - : IEEE conference proceedings. - 0018-9375 .- 1558-187X. ; 53:1, s. 18-27
-
Journal article (peer-reviewed)abstract
- Pantograph arcing in ac traction system generates transients, and causes asymmetries and distortion in supply voltage and current waveforms. These asymmetric voltage and current lead to a net dc component and harmonics that propagate within the traction power and signalling system and cause electromagnetic interference. This problem is enhanced during winter because of the layer of ice/snow on the overhead contact wire. The sliding contact becomes poor and a visible arc moves along with the pantograph. In this paper, it is shown how different parameters like traction current, line speed, power factor, and supply voltage influence the arcing, its characteristics, and the dc components. It is shown that the dc current component increases with increasing train speed and traction current, and reduces at a lower power factor. It is also discussed how the presence of an ice layer influences the arcing and the dc components. It is found that running the trains below the normal operating power factors is an effective choice to mitigate this problem. The findings presented in this paper could be beneficial to estimate the probable limit of the dc component at the planning stage so that proper precautions can be taken at the design stage itself.
|
|
24. |
- Ribeiro, Luis, et al.
(author)
-
Industrial Agents for the Fast Deployment of Evolvable Assembly Systems
- 2015. - 1st ed.
-
In: Industrial Agents. - Amsterdam, Netherlands : Elsevier. - 9780128003411 ; , s. 301-321, s. 301-322
-
Book chapter (peer-reviewed)abstract
- The current manufacturing scenario is characterized by high market unpredictability. Agility is therefore a central challenge for modern companies that need to understand and be proactive towards their product offer in respect to “what is offered, when it is offered, where, how and by whom” (Brown & Bessant 2003).The “what” and the “when” are particularly relevant to the research in emerging paradigms as they account for variety, customization and volume; and timing, speed and seasonality (Brown & Bessant 2003).In this scenario, several design approaches and models have been proposed in the last decade to enable re-configurability and subsequently enhance the companies’ ability to adjust their offer in nature and time.From a paradigmatic point of view research has concentrated on the organizational structure of the shop-floor and the associated controls aspects. Concepts like Reconfigurable Manufacturing Systems (RMS) (Koren & Shpitalni 2010) and Fractal Factories (FF) (Montreuil 1999) support the physical construction of production systems by regulating their layout and making a few assumptions on their logical organization. On the other hand, concepts like Bionic Manufacturing Systems (BMS)(Ueda 1992), Holonic Manufacturing Systems (HMS)(Van Brussel et al. 1998), Evolvable Assembly Systems (Ribeiro et al. 2010) essentially provide the theoretical guidelines for the logical/computational organization of the system (see (Tharumarajah 1996) for a comparison between BMS, HMS and FF and (Setchi & Lagos 2004) for the rationale supporting the shift from Dedicated Lines to Flexible Manufacturing System and finally RMS).While these paradigms provide the conceptual framework and the main design guidelines their actual interpretation and implementation has led to a wider set of architectures (Monostori, Váncza & Kumara 2006; Leitão 2009; Parunak 2000; Pěchouček & Mařík 2008).These architectures align the high-level principles with the technological offer and limitations while seeking to address the re-configurability requirements of (Mehrabi, Ulsoy & Koren 2000; Rösiö & Säfsten 2013):module mobility – modules are easy and quick to move and install;“diagnosability” – it is quick to identify the sources of quality and reliability problems;“integrability” – modules are easy to integrate into the rest of the system.“convertibility” – it is easy and quick to switch between existing products and it is easy to adapt the system to future products;scalability – it is easy to enlarge and downsize the production system;“automatibility” – a dynamic level of automation is enabled;modularity – all system elements are designed to be modular;customization – the capability and flexibility of the production system is designed according to the products to be produced in the system.Instant deployment, as addressed in the present chapter directly addresses mobility, “integrability”, “convertibility”, scalability and customization. Mechatronic modularity is a prerequisite and is enforced by the proposed architecture and the considered modular design. “Diagnosability” was not specifically tackled.In this context, the chapter analyses the agent-based architecture related with the Instantly Deployable Evolvable Assembly System (IDEAS) project that is inspired by the Evolvable Assembly System (EAS) paradigm (Ribeiro et al. 2010) as a mechanism to enable fast deployment of mechatronic modules. EAS advocates the use of process-oriented modules and envisions the production system as a collection of processes and the associated interacting agents.The architecture and the related test cases are used to draw the main lessons learned in respect to technological and conceptual implications.In this context, the remainder of this text is organized as follows: section 1.1 discusses the main deployment challenges, section 1.2 details the reference architecture and associated concepts, section 1.3 presents the principal implementation decisions, section 1.4 features the main lessons learned, sections 1.5 discusses the benefits of the proposed approach and finally section 1.6 reflects on the main conclusions.
|
|
25. |
- Kleyko, Denis, et al.
(author)
-
Vehicle Classification using Road Side Sensors and Feature-free Data Smashing Approach
- 2016
-
In: 2016 IEEE 19th International Conference on Intelligent Transportation Systems (ITSC). - Piscataway : IEEE. - 9781509018895 - 9781509018888 - 9781509018901 ; , s. 1988-1993
-
Conference paper (peer-reviewed)abstract
- The main contribution of this paper is a study of the applicability of data smashing - a recently proposed data mining method - for vehicle classification according to the "Nordic system for intelligent classification of vehicles" standard, using measurements of road surface vibrations and magnetic field disturbances caused by passing vehicles. The main advantage of the studied classification approach is that it, in contrast to the most of traditional machine learning algorithms, does not require the extraction of features from raw signals. The proposed classification approach was evaluated on a large dataset consisting of signals from 3074 vehicles. Hence, a good estimate of the actual classification rate was obtained. The performance was compared to the previously reported results on the same problem for logistic regression. Our results show the potential trade-off between classification accuracy and classification method's development efforts could be achieved.
|
|
26. |
- Sarkar, Saptarshi, 1992, et al.
(author)
-
Transient torque reversals in indirect drive wind turblnes
- 2023
-
In: Wind Energy. - 1099-1824 .- 1095-4244. ; 26, s. 691-716
-
Journal article (peer-reviewed)abstract
- The adverse effect of transient torque reversals (TTRs) оп wind turЬine gearboxes сап Ье severe due to their magnitude and rapid occurrence compared with other equipment. The primary damage is caused to the bearings as the bearing loaded zone rapidly changes its direction. Other components are also affected Ьу TTRs (such as gear tooth); however, its impact оп bearings is the largest. While the occurrence and severity of TTRs are acknowledged in the industry, there is а lack of academic literature оп their initiation, propagation and the associated risk of damage. Furthermore, in the wide range of operation modes of а wind turЬine, it is not known which modes сап lead to TTRs. Further, the interdependence of TTRs оп environmental loading like the wind is also not reported. This paper aims to address these unknowns Ьу expanding оп the understanding of TTRs using а high-fidelity numerical model of an indirect drive wind turЬine with а douЬly fed induction generator (DFIG). То this end, а multibody model of the drivetrain is developed in SIMPACK. The model of the drivetrain is explicitly coupled to state-of-the-art wind turЬine simulator OpenFAST and а grid-connected DFIG developed in MATLAB®'s Simulink® allowing а coupled analysis of the electromechanical system. А metric termed slip risk duration is proposed in this paper to quantify the risk associated with the TTRs. The paper first investigates а wide range of IEC design load cases to uncover which load cases сап lead to TTRs. lt was found that emergency stops and symmetric grid voltage drops сап lead to TTRs. Next, the dependence of the TTRs оп inflow wind parameters is investigated using а sensitivity analysis. lt was found that the instantaneous wind speed at the onset of the grid fault or emergency shutdown was the most influential factor in the slip risk duration. The investigation enaЫes the designer to predict the occurrence of TTRs and quantify the associated risk of damage. The paper concludes with recommendations for utility-scale wind turЬines and directions for future research.
|
|
27. |
- Lejon, Marcus, 1986, et al.
(author)
-
Multidisciplinary Design of a Three Stage High Speed Booster
- 2017
-
In: ASME Turbo Expo 2017: Turbine Technical Conference and Exposition. - : ASME Press. ; 2B-2017
-
Conference paper (peer-reviewed)abstract
- The paper describes a multidisciplinary conceptual design of an axial compressor, targeting a three stage, high speed, high efficiency booster with a design pressure ratio of 2.8. The paper is outlined in a step wise manner starting from basic aircraft and engine thrust requirements, establishing the definition of the high speed booster interface points and its location in the engine. Thereafter, the aerodynamic 1D/2D design is carried out using the commercial throughflow tool SC90C. A number of design aspects are described, and the steps necessary to arrive at the final design are outlined. The SC90C based design is then carried over to a CFD based conceptual design tool AxCent, in which a first profiling is carried out based on a multiple circular arc blade definition. The design obtained at this point is referred to as the VINK compressor. The first stage of the compressor is then optimized using an in-house optimization tool, where the objective functions are evaluated from detailed CFD calculations. The design is improved in terms of efficiency and in terms of meeting the design criteria put on the stage in the earlier design phases. Finally, some aeromechanical design aspects of the first stage are considered. The geometry and inlet boundary conditions of the compressor are shared with the turbomachinery community on a public server. This is intended to be used as a test case for further optimization and analysis.
|
|
28. |
- Li, Xiaojian, 1991, et al.
(author)
-
Installation effects on engine design
- 2020
-
Conference paper (other academic/artistic)abstract
- Increasing the engine bypass ratio is one way to improve propulsive efficiency. However, an increase in the bypass ratio (BPR) has usually been associated with an increase in the fan diameter. Consequently, there can be a notable increase in the impact of the engine installation on the overall aircraft performance. In order to achieve a better balance between those factors, it requires novel nacelle and engine design concepts. This report mainly reviews installation effects on engine design. Firstly, the installation effects assessment methods are introduced. Then, the installation effects on engine cycle design, intake design and exhaust design are sequentially reviewed.
|
|
29. |
- Berbyuk, Viktor, 1953
(author)
-
Structural Dynamics Control, Third Edition
- 2020
-
Book (other academic/artistic)abstract
- Structural dynamics and especially one of its main problems, vibrations and vibration control, appear in vehicle engineering, high precision machines and mechanisms, robotics, civil engineering, wind turbines, biomechanics, and others. Over the last decades there has been much work concerned with the vibration control of different dynamical systems. The texbook “Structural Dynamics Control” aims at providing knowledge on modern methods and concepts of passive, semi-active and active vibration control, to cross the bridge between structural dynamics and control engineering, while providing an overview of the potential of smart materials, (magnetorheological fluids, magnetostrictive materials, and others), for sensing and actuating purposes in active vibration control. One of the aims of this textbook is to provide students and engineers with opportunity of becoming familiar with the standard methods of the classical calculus of variations, the linear quadratic regulator optimization methods, and modern optimal control theory with focus on their applications in structural dynamics for vibration attenuation and vibration suppression problems. The textbook consists of four main parts: Vibration dynamics, Passive and semi-active vibration control, Active and hybrid vibration control, and Applications. The textbook ends with the supplementary mathematics, list of Matlab codes and answers and hints for the exercises. The list of references consists of only those books and scientific papers which were used during preparation of the textbook or which have been recommended to stundents for additional information on a studied topic. The textbook is aimed at first towards graduate and postgraduate students following Master and PhD programmes related to structural dynamics, mechatronics, control engineering, automotive engineering, noise and vibrations. The only prerequisite for reading this book is basic knowledge in mechanics and some familiarity with vibrations, state space models and automatic control.
|
|
30. |
- De Backer, Jeroen, 1987-, et al.
(author)
-
Friction stir welding with robot for light vehicle design
- 2010
-
In: Proceedings from the 8<sup>th</sup> International Friction Stir Welding Symposium. - : The Welding Institute. - 1903761085 - 9781903761083
-
Conference paper (other academic/artistic)abstract
- Reducing weight is one of the enablers to design more environmentally friendly vehicles. Friction Stir Welding (FSW) supports low weight design through its capability to join different combinations of light weight materials, e.g. different aluminium alloys, but also through its possibilities in producing continuous joints. StiRoLight is a recently started project for robotised FSW for joining of light weight materials emphasising on the vehicle industry, an industry with a long-time experience of robotic welding. The first task involves investigation of force feedback for maintaining the desired contact force. Another important aspect in robotised FSW is the compliance of the robot, which may result in deviations from the pre-programmed path as a result of the high process forces experienced during the welding operation. The further exploration of three-dimensional FSW seams and definition of the process windows will be part of further research within this project.
|
|
31. |
- Eriksson, Lars, 1970-, et al.
(author)
-
Dynamic Modeling, Simulation and Control of Turbochargers
- 2017
-
In: Dynamic Modeling, Simulation and Control of Turbochargers. - : Nova Science Publishers, Inc.. - 9781536122398 ; , s. 176-206
-
Book chapter (other academic/artistic)abstract
- Turbochargers stand for the dominating dynamics in engines and in the design, analysis, and optimization of new engines, it becomes more and more important to analyze system interactions and dynamics. In the development process, modeling, simulation, and optimization have evolved from being used in research to being stan- dard tools for engineers and play an important role in the engine development. To be successful in the process, one needs to both have component models, and methods and tools where system models can be built, analyzed, and optimized. The component models should also have capabilities to extrapolate behavior outside the nominal re- gion since design explorations can go to extreme points while searching for optimal solutions.The first part of the chapter summarizes the compressor and turbine maps and how they can be used in simulation models. A generic model structure for compressors and turbines that fit into an engine modeling and simulation framework is described. Then the Ellipse compressor flow model and the Enthalpy based efficiency model will be described, they have been developed so that they can be integrated in a simulation environment and also used in optimization. Their main features are that they are ca- pable of extrapolating compressor behavior outside the normal range of the map in a physically sane way. In addition to this, a tuning method has been developed that takes a normal manufacturer map and returns all model parameters for compressor flow and efficiency models. Thereafter, compact turbine flow and efficiency models will be described.Then the attention is turned to simulation and optimization applications where compressor models are used. First an engine experiment where compressor surge oc- curs is modelled and used to illustrate the extrapolation capabilities using the models presented. Then the scope is turned to control and optimization of turbocharger opera- tion on an engine, where the focus will be on a VGT controlled diesel engine equipped with EGR. First the steady state mapping of the engine is demonstrated, then optimal control of the turbo operation is investigated using modern computer tools for dynamic optimization.
|
|
32. |
- Stylidis, Kostas, 1978, et al.
(author)
-
Perceived quality of products: a framework and attributes ranking method
- 2020
-
In: Journal of Engineering Design. - : Informa UK Limited. - 1466-1837 .- 0954-4828. ; 31:1, s. 37-67
-
Journal article (peer-reviewed)abstract
- Perceived quality is one of the most critical aspects of product development that defines the successful design. This paper presents a new approach to perceived quality assessment by examining its elements, decomposed into a structure with the bottom-up sensory approach from the level of basic (‘ground’) attributes, covering almost every aspect of quality perception from the engineering viewpoint. The paper proposes a novel method for perceived quality attributes relative importance ranking, resulting in the balanced perceived quality of the final product within the given conditions. The proposed method helps to reach the equilibrium of the product’s quality equation from the perspective of design effort, time, and costs estimations. The authors introduce the Perceived Quality Framework (PQF), which is the taxonomy system for perceived quality attributes and the core of the attributes importance ranking (PQAIR) method. The research outcomes are based on findings of the qualitative exploratory study, including European and North American premium and luxury automotive manufacturers. An empirical structural validity test was performed to assess the usability and rigour of the proposed method. The results indicate that perceived quality evaluation can be significantly improved during all stages of product development.
|
|
33. |
- Vilardell, A. M., et al.
(author)
-
B2-structured Fe3Al alloy manufactured by laser powder bed fusion : Processing, microstructure and mechanical performance
- 2023
-
In: Intermetallics (Barking). - : Elsevier. - 0966-9795 .- 1879-0216. ; 156
-
Journal article (peer-reviewed)abstract
- Prealloyed Fe3Al was successfully manufactured by laser powder bed fusion. The best set of process parameters led to parts with a relative density of 99.5 %, a surface roughness, Sa, of 31.5 ± 5.6 μm and a hardness of 319 ± 14 HV0.1. Its microstructure as well as its mechanical properties at room and high temperatures were analyzed. The results of the chemical composition showed minor variations in aluminum content oscillating between 21 and 28 at.% along the melt pool. Additionally, elongated grains were observed to grow parallel to the building direction, as well as the development of a weak 001 texture along the building direction. The mechanical properties were influenced by the temperature. Compression tests showed a loss in strength with the increase in temperature, from a yield strength of 621 ± 40 MPa at room temperature to 89 ± 20 MPa at 650 °C. Reciprocating sliding wear tests showed that fragmentation of the intermetallic at room temperature occurs, whereas plastic deformation dominated at higher temperatures. For all temperatures, tribochemical wear was also present due to the oxidation of wear debris.
|
|
34. |
- Johansson, Björn, 1975, et al.
(author)
-
Power Level Sampling of Metal Cutting Machines for Data Representation in Discrete Event Simulation
- 2015
-
In: International Journal of Production Research. - : Informa UK Limited. - 0020-7543 .- 1366-588X. ; 53:23, s. 7060-7070
-
Journal article (peer-reviewed)abstract
- An extension to the application area for discrete event simulation (DES) has been ongoing since the last decade and focused only on economic aspects to include ecologic sustainability. With this new focus, additional input parameters, such as electrical power consumption of machines, are needed. This paper aim at investigating how NC machine power consumption should be represented in simulation models of factories. The study includes data-sets from three different factories. One factory producing truck engine blocks, one producing brake disc parts for cars and one producing forklift components. The total number of data points analysed are more than 2,45,000, where of over 1,11,000 on busy state for 11 NC machines. The low variability between busy cycles indicates that statistical representations are not adding significant variability. Furthermore, results show that non-value-added activities cause a substantial amount of the total energy consumption, which can be reduced by optimising the production flow using dynamic simulations such as DES.
|
|
35. |
- Stylidis, Kostas, 1978
(author)
-
Perceived Quality of Cars. A Novel Framework and Evaluation Methodology.
- 2019
-
Doctoral thesis (other academic/artistic)abstract
- The supremacy of the automotive manufacturers today is no longer driven by them achieving a superior manufacturing quality but increasingly depends on the customer’s quality perception. Average car consumers see a car’s quality as a fancy mixture of design, aesthetics, their own previous experiences and performance characteristics of the vehicle, unlike a combination of mechanical parts, software pieces, advanced materials, cutting-edge manufacturing processes, with technical knowledge, skills and high production volumes – all ingredients involved in the modern car creation. Perceived quality is one of the most critical aspects for product development that defines successful car design. Speaking of perceived quality, we are dealing with a complex, multifaceted adaptive system; a system where a human is the main agent. “Which product characteristics require the most attention for successful car design?” This is the question engineers and designers need to answer under the pressure of shrinking product development time, available technologies, and financial limitations, not to mention that the answer is expected to be given in numbers to sustain the fierce competition in today’s automotive industry. For this reason, the perceived quality must be understood and controlled during all stages of product development. The research presented in this thesis justifies the engineering viewpoint on perceived quality as an inevitable part of new product development. The core of this research is the Perceived Quality Framework (PQF), a taxonomy structure of perceived quality attributes and the Perceived Quality Attributes Importance Ranking (PQAIR) method, a novel method for perceived quality evaluation that can be applied to a variety of products, including cars. The PQF communicates the attribute-centric engineering viewpoint on quality perception, developed through cumulative studies in the premium and luxury market segment of the automotive industry. The PQAIR method equips engineers with practical tools for perceived quality evaluation. The proposed method helps to reach the equilibrium of the product’s quality equation from the perspective of design effort, time, and costs estimations. Altogether this introduces a new paradigm of perceived quality as the inevitable element integrated into the process of engineering endeavor regarding product attributes that communicates quality to the customer.
|
|
36. |
|
|
37. |
- Thulin, Oskar, 1987, et al.
(author)
-
First and Second Law Analysis of Radical Intercooling Concepts
- 2018
-
In: Journal of Engineering for Gas Turbines and Power. - : ASME International. - 1528-8919 .- 0742-4795. ; 140:8, s. 081201-081201-10
-
Journal article (peer-reviewed)abstract
- An exergy framework was developed taking into consideration a detailed analysis of the heat exchanger (HEX) (intercooler (IC)) component irreversibilities. Moreover, it was further extended to include an adequate formulation for closed systems, e.g., a secondary cycle (SC), moving with the aircraft. Afterward, the proposed framework was employed to study two radical intercooling concepts. The first proposed concept uses already available wetted surfaces, i.e., nacelle surfaces, to reject the core heat and contributes to an overall drag reduction. The second concept uses the rejected core heat to power a secondary organic Rankine cycle and produces useful power to the aircraft-engine system. Both radical concepts are integrated into a high bypass ratio (BPR) turbofan engine, with technology levels assumed to be available by year 2025. A reference intercooled cycle incorporating a HEX in the bypass (BP) duct is established for comparison. Results indicate that the radical intercooling concepts studied in this paper show similar performance levels to the reference cycle. This is mainly due to higher irreversibility rates created during the heat exchange process. A detailed assessment of the irreversibility contributors, including the considered HEXs and SC, is made. A striking strength of the present analysis is the assessment of the component-level irreversibility rate and its contribution to the overall aero-engine losses.
|
|
38. |
- Thulin, Oskar, 1987
(author)
-
On the Analysis of Energy Efficient Aircraft Engines
- 2017
-
Doctoral thesis (other academic/artistic)abstract
- Aero engine performance analysis is highly multidimensional using various measures of component performance such as turbomachinery and mechanical efficiencies, and pressure loss coefficients. Using conventional performance analysis, relying on only the laws of thermodynamics, it is possible to understand how the performance parameters affect the component performance, but it is difficult to directly compare the magnitude of various loss sources. A comprehensive framework has been detailed to analyze aero engine loss sources in one common currency. As the common currency yields a measure of the lost work potential in every component, it is used to relate the component performance to the system performance. The theory includes a more detailed layout of all the terms that apply to a propulsion unit than presented before. The framework is here adopted to real gases to be used in state of the art performance codes. Additionally, the framework is further developed to enable detailed studies of two radical intercooling concepts that either rejects the core heat in the outer nacelle surfaces or uses the core heat for powering of a secondary cycle. The theory is also extended upon by presenting the installed rational efficiency, a true measure of the propulsion subsystem performance, including the installation effects of the propulsion subsystem as it adds weight and drag that needs to be compensated for in the performance assessment.
|
|
39. |
- Högman, Ulf, 1961, et al.
(author)
-
Requirements on New Technology and the Technology Implementation Process
- 2010
-
In: 8th International NordDesign Conference, NordDesign 2010; Goteborg; Sweden; 25 August 2010 through 27 August 2010. ; 2, s. 289-300
-
Conference paper (peer-reviewed)abstract
- In literature, many authors have pointed to the importance of technology and technology development for company competitiveness. In this study we aim to study the technology in more detail and attempt to develop an understanding on the requirements and needs on “technology” from the perspective of product development. The research question which we aim to answer in this study is:“What are the requirements on maturity of technology when this technology is about to enter into the product development process?“A qualitative research strategy, based on three study cases involving 17 interviewees, has been chosen. All three cases come from one single company, Volvo Aero Corporation (VAC) in Sweden, in the context of the aero engine industry. The study contributes with a broad mapping of requirements and how they relate to different categories of technologies, showing big differences both regarding content and timing. It is concluded that attention should be payed both to how the organization builds new capabilities and to the capabilities of the technology itself. A surprisingly complicated picture on the requirements relating to the implementation of new technologies has emerged in the study. This contributes to the understanding regarding the difficulties of developing new technology and integrating it into an application.
|
|
40. |
- Li, Xiaojian, 1991, et al.
(author)
-
A new method for performance map prediction of automotive turbocharger compressors with both vaneless and vaned diffusers
- 2021
-
In: Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering. - : SAGE Publications. - 2041-2991 .- 0954-4070. ; 235:6, s. 1734-1747
-
Journal article (peer-reviewed)abstract
- A new approach to predict the performance maps of automotive turbocharger compressors is presented. Firstly, a polynomial equation is applied to fit the experimental data of flow coefficient ratios for the centrifugal compressors with both vaneless and vaned diffusers. Based on this equation, the choke and surge flow coefficients under different machine Mach numbers can be quickly predicted. Secondly, a physically based piecewise elliptic equation is used to define compressors’ characteristic curves in terms of efficiency ratio. By introducing the flow coefficient ratio into the efficiency correlation, the empirical coefficients in the piecewise elliptic equation are uniquely calibrated by the experimental data, forming a unified algebraic equation to match the efficiency maps of the compressors with both vaneless and vaned diffusers. Then, a new universal equation, which connects the work coefficient, the impeller outlet flow coefficient and the non-dimensional equivalent impeller outlet width, is derived by using classical aerothermodynamic method. The off-design pressure ratio is predicted based on the equivalent impeller outlet width with less knowledge of the compressor geometry and no empirical coefficients. Finally, three state-of-the-art turbocharger compressors (one with vaneless diffuser, two with vaned diffusers) are chosen to validate the proposed method, and the results show a satisfactory accuracy for the performance map prediction. This method can be used for the preliminary design of turbocharger compressors with both vaneless and vaned diffusers, or to assess the design feasibility and challenges of the given design specifications.
|
|
41. |
- Ågren, Magnus, 1984, et al.
(author)
-
The manager perspective on requirements impact on automotive systems development speed
- 2018
-
In: Proceedings - 2018 IEEE 26th International Requirements Engineering Conference, RE 2018. - : IEEE. ; , s. 17-28
-
Conference paper (peer-reviewed)abstract
- Context: Historically, automotive manufacturers have adopted rigid requirements engineering processes, which allowed them to meet safety-critical requirements while integrating thousands of physical and software components into a highly complex and differentiated product. Nowadays, needs of improving development speed are pushing companies in this domain towards new ways of developing software. Objectives: We aim at obtaining a manager perspective on how the goal to increase development speed impacts how software intense automotive systems are developed and their requirements managed. Methods: We used a qualitative multiple-case study, based on 20 semi-structured interviews, at two automotive manufacturers. Our sampling strategy focuses on manager roles, complemented with technical specialists. Results: We found that both a requirements style dominated by safety concerns, and decomposition of requirements over many levels of abstraction impact development speed negatively. Furthermore, the use of requirements as part of legal contracts with suppliers hiders fast collaboration. Suggestions for potential improvements include domain-specific tooling, model-based requirements, test automation, and a combination of lightweight pre-development requirements engineering with precise specifications post-development. Conclusions: We offer an empirical account of expectations and needs for new requirements engineering approaches in the automotive domain, necessary to coordinate hundreds of collaborating organizations developing software-intensive and potentially safety-critical systems.
|
|
42. |
- Han, Weiji, 1987, et al.
(author)
-
Next-Generation Battery Management Systems: Dynamic Reconfiguration
- 2020
-
In: IEEE Industrial Electronics Magazine. - 1941-0115 .- 1932-4529. ; 14:4, s. 20-31
-
Journal article (peer-reviewed)abstract
- Batteries are widely applied to the energy storage and power supply in portable electronics, transportation, power systems, communication networks, etc. They are particularly demanded in the emerging technologies of vehicle electrification and renewable energy integration for a green and sustainable society. To meet various voltage, power, and energy requirements in large-scale applications, multiple battery cells have to be connected in series and/or parallel. While battery technology has advanced significantly in the past decade, existing battery management systems (BMSs) mainly focus on state monitoring and control of battery systems packed in fixed configurations. In fixed configurations, though, the battery system performance is in principle limited by the weakest cells, which can leave large parts severely underutilized. Allowing dynamic reconfiguration of battery cells, on the other hand, allows individual and flexible manipulation of the battery system at cell, module, and pack levels, which may open up a new paradigm for battery management. Following this trend, this paper provides an overview of next-generation BMSs featuring dynamic reconfiguration. Motivated by numerous potential benefits of reconfigurable battery systems (RBSs), the hardware designs, management principles, and optimization algorithms for RBSs are sequentially and systematically discussed. Theoretical and practical challenges during the design and implementation of RBSs are highlighted in the end to stimulate future research and development.
|
|
43. |
- Somhorst, Joop, 1965
(author)
-
Thermal insulation of the combustion chamber in a light duty diesel engine
- 2024
-
Doctoral thesis (other academic/artistic)abstract
- Reduction of heat loss from the combustion chamber in an engine has great potential to decrease fuel consumption and CO2 emissions. Research on thermal barrier coatings (TBC) has been performed since the early eighties to address this potential. However, reported results for engine efficiency improvements with insulation show a large spread and there is no consensus on the actual benefits of TBCs. The purpose of this PhD project was to make an accurate assessment of state-of-the-art TBCs and establish what coating properties are required to improve indicated engine efficiency. Cylinder pressure data and measured heat losses to the piston cooling oil in a light duty single cylinder engine formed the basis for the experimental research. A robust and automated measurement method was developed and combined with statistical modeling of the data. Plasma sprayed yttria stabilized zirconia and anodized alumina were selected to establish the effectiveness of state-of-the-art TBCs. These coatings, applied on the piston top, did not improve indicated efficiency. The high surface roughness of the coatings was an important contributor to the poor performance. Experiments with a novel coating technology: suspension plasma spraying and a new material gadolinium-zirconate, led to a slightly improved indicated efficiency. Details in the heat release analysis indicated that the high open porosity in this coating might lead to increased heat losses and fuel entrainment. An investigation of possible charge entrainment effects in a standard plasma sprayed zirconia thermal barrier coating was performed, using a combination of engine experiments, CFD simulations and a 0D crevice model. The crevice model predicted the observed deviations of the apparent rate of heat release surprisingly well, which is strong evidence for the existance and significance of this crevice effect. To significantly increase engine efficiency with thermal insulation, materials with further reduced thermal conductivity and volumetric heat capacity are needed, while negative effects such as high surface roughness and crevice effects from permeable porosity should be minimized.
|
|
44. |
- Lindskog, P, et al.
(author)
-
Optimization as a tool for characterization of advanced constitutive models describing powder compaction
- 2007
-
In: Proceedings of the Euro PM 2007 Congress and Exhibition. - Shrewsbury : European Powder Metallurgy Association. ; , s. 381-386
-
Conference paper (peer-reviewed)abstract
- The applicability of optimization procedures used in combination with advanced constitutive models, describing dry pressing powder compaction, is investigated by aid of standard finite ele- ment and optimization commercial packages. It is found that, at fairly general conditions, this can be expected to be a very advantageous approach at material characterization
|
|
45. |
- Sandberg, Marcus, et al.
(author)
-
A modelling methodology for assessing use of datacenter waste heat in greenhouses
- 2017
-
Conference paper (peer-reviewed)abstract
- In Sweden, the number of datacenters establishments are steadily increasing thanks to green, stable and affordable electricity, free air cooling, advantageous energy taxes and well-developed Internet fiber infrastructures. Even though datacenters use a lot of energy, the waste heat that they create is seldom reused. A possible cause is that this waste heat is often low grade and airborne: it is therefore hard to directly inject it into a district heating system without upgrades, which require additional energy and equipment that generate extra costs. One option for reusing this heat without needs for upgrades is to employ it for heating up greenhouses. But assessing the feasibility of this approach by building physical prototypes can be costly, therefore using computer models to simulate real world conditions is an opportunity. However, there is a lack of computer modelling methodologies that can assess the possibility of using waste heat from datacenters in greenhouses in cold climates.The objective of this paper is therefore to propose such a methodology and discuss its benefits and drawbacks in comparison with other research studies. This methodology combines computational fluid dynamics, process modelling and control engineering principles into a computer model that constitutes a decision support system to study different waste heat and greenhouse or mushroom house scenarios.The paper validates the strategy through a case study in northern Sweden, where we assess the amount of produced waste heat by collecting temperature, relative humidity, and fan speed data for the air discharged from the datacenter.The resulting methodology, composed by conducting measurements and computer models, calculations can then be used for other datacenter operators or greenhouse developers to judge whether it is possible or not to build greenhouses using datacenter waste heat.
|
|
46. |
- De Vin, Leo, 1957-
(author)
-
Credibility of Simulation Results – a Philosophical Perspective on Virtual Manufacturing
- 2012
-
In: Proceedings of the 13th Mechatronics Forum International Conference. - Linz : TRAUNER Verlag. - 9783990330463 ; , s. 784-791
-
Conference paper (peer-reviewed)abstract
- This paper describes the factors that play a role in credibility of simulation results. It focuses on virtual manufacturing and in particular resource simulation as an example. However, a simulation model can be used in a number of different ways. Verification and validation of models is amongst other factors important for credibility. In this area, much work has been carried out in defense research. There are also some striking similarities between virtual manufacturing and information fusion, in particular in the field of human competence development related to credibility of simulations.
|
|
47. |
- Tofique, Muhammad Waqas, 1986-, et al.
(author)
-
Development of the distributed dislocation dipole technique for the analysis of closure of complex fractures involving kinks and branches
-
Other publication (other academic/artistic)abstract
- This paper presents the development of the distributed dislocation dipole technique (DDDT) for the analysis of crack surface closure of crack cases involving kinks and branches. Crack cases in which closure occurs are analyzed by reformulating the Bueckner's principle taking the contact stresses at the contacting portions of the crack surfaces into account. Stress intensity factors corresponding to opening and sliding mode of deformation at the crack tips are computed. Three test cases involving kinked and/or branched cracks with at least one of the crack segments undergoing crack surface closure when subjected to remote tensile loading are analyzed. The results obtained from the DDDT are compared to those obtained from the Finite Element Method (FEM) analysis of the same crack cases. This comparison shows that the computation of stress intensity factors for the crack cases involving crack surface closure are less acurate compared to fully open crack cases. However, the stress intensity factors are still computed to an accuracy of within 2 percent if the Jacobi polynomial expansions of at least the sixth order are used to represent the crack surface opening and sliding displacements. Higher order Jacobi polynomials lead to increased accuracy.
|
|
48. |
|
|
49. |
- Blomé, Mikael, et al.
(author)
-
Course Supervision Challenges in PhD Education
- 2012
-
In: 7:e Pedagogiska Inspirationskonferensen 2012. - 2003-3761 .- 2003-377X. ; 7
-
Conference paper (peer-reviewed)abstract
- A large portion of the PhD education in Sweden is dedicated to courses. This made it interesting to explore potential course supervision challenges in the PhD programme. A multiple-case study was conducted to identify such challenges and explore how these are perceived by students and supervisors at the Faculty of Engineering of Lund University. By interviewing students and supervisors in five different research groups, insights were gained into how the main stakeholders reason about courses. The findings indicate that courses that are to be included in the education are characterized by a large degree of freedom tailored to individual student needs and preferences. However, the type, timing, availability, value, and convalidation of courses are challenges that limit this freedom.
|
|
50. |
- Isaksson, Ola, 1969, et al.
(author)
-
Trends, observations and drivers for change in systems engineering design
- 2017
-
In: Proceedings of the International Conference on Engineering Design, ICED. - : The Design Society. ; 3, s. 201-210
-
Conference paper (peer-reviewed)abstract
- Manufactures, developing products, need to adapt and improve their practices taking advantage of technology advancements and simultaneously develop products and solutions to fit a new world. This paper discusses how societal and technological trends drive the need for change and evolution in what is called Systems Engineering Design (SED), indicating a systems view on engineering design. Through an analysis and selected examples it is argued that SED capabilities need to better address the width and complexity of design problem, takes advantages of increased computational power and sensing technologies to master future challenges. An important factor for successful deployment and change in industrial context, is the need for interactive and visual AIDS and easily accessible support methods. This can pave the way also for advanced SED support.
|
|