1. |
- Adanez-Rubio, Inaki, et al.
(author)
-
Cu-Mn oxygen carrier with improved mechanical resistance: Analyzing performance under CLC and CLOU environments
- 2021
-
In: Fuel Processing Technology. - : Elsevier BV. - 0378-3820. ; 217
-
Journal article (peer-reviewed)abstract
- Chemical Looping Combustion process allows combustion of gaseous, liquid or solid fuels with CO capture. The oxygen necessary for combustion can be supplied using lattice oxygen (CLC) or oxygen uncoupling (CLOU) mechanisms. The present work studies the effects of kaolin addition on Cu–Mn oxygen carrier behavior for CLC and CLOU processes. Cu–Mn oxygen carrier was prepared by granulation with a composition: 27.2 wt% CuO, 52.8 wt% Mn O and 20 wt% kaolin. Oxygen release rates and fluidization behavior were analyzed by TGA and batch fluidized bed reactor. The oxygen carrier was studied for CH and synthetic biogas combustion in a 500 W CLC continuous unit for 50 h of combustion at temperatures up to 930 °C. No agglomeration problems were observed. Results found during biogas combustion were similar to methane combustion. The addition of 20 wt% kaolin changed the mixed oxide chemical composition generating Cu Mn O and improved significantly the oxygen carrier mechanical resistance, increasing the extrapolated lifetime to 19,000 h, 3.6 times over the value found for any Cu based oxygen carrier in CLC. However, the oxygen carrier reactivity had an important decrease with respect to a similar oxygen carrier without kaolin addition, whose fraction in oxygen carrier must be optimized. 2 3 4 4 th 1.2 1.8 4
|
|
2. |
- Adanez-Rubio, Inaki, et al.
(author)
-
Development of new Mn-based oxygen carriers using MgO and SiO 2 as supports for Chemical Looping with Oxygen Uncoupling (CLOU)
- 2023
-
In: Fuel. - : Elsevier BV. - 0016-2361. ; 337
-
Journal article (peer-reviewed)abstract
- Chemical Looping with Oxygen Uncoupling (CLOU) is a technological adaptation of CLC, most applicable for the combustion of solid fuels. In the CLOU process, an oxygen carrier in the fuel reactor, avoiding the direct contact of the fuel with the air, releases the oxygen needed for the fuel combustion. The oxygen carrier is regenerated with air in the interconnected air reactor. The present work explores the behavior of the system Mn/Mg/Si as oxygen carriers for chemical-looping with oxygen uncoupling (CLOU). Six different mixed oxides of the system Mn/Mg/Si were investigated for the CLC/CLOU process. Materials were prepared by spray drying with different metal ratios used in the investigation. The properties of interest for the viability of these materials are the lattice oxygen supply for CLC and the gaseous oxygen release for CLOU, properties that were explored in a TGA. Further, the fluidization behavior and the mechanical resistance were investigated in a batch fluidized bed reactor. In the TGA it was observed that the most reactive oxygen carriers for the CLOU process were materials without Si in the structure, more specifically M24Mg76 and M48Mg51 which had a molar ratio of Mn/Mg of 0.17 and 0.51 respectively. It was also observed that for the oxygen carriers with Si in the composition, the regeneration was very poor. Oxygen carriers M24Mg76 and M48Mg51 were selected for batch fluidized bed reactor testing showing good behavior with respect to the CLOU reactivity, and mechanical stability. One of the materials, the M24Mg76 showed activation during the experiments in the batch fluidized bed reactor experiments, increasing the oxygen transport capacity by 20 % during the experiment. However, 10 vol% of O2 was needed to regenerate both oxygen carriers at 850 °C. No agglomeration tendencies were seen, and the attrition rate was low, obtaining high-extrapolated lifetime values. The fact that highly reactive oxygen carriers can be made with cheap and highly available metals oxides, i.e. Mn and Mg, makes this system very promising and a possible alternative to benchmark Cu-based CLOU materials.
|
|
3. |
- Adanez-Rubio, Inaki, et al.
(author)
-
Use of a high-entropy oxide as an oxygen carrier for chemical looping
- 2024
-
In: Energy. - 0360-5442 .- 1873-6785. ; 298
-
Journal article (peer-reviewed)abstract
- One mixed oxide with 5 cations in equimolar proportions in the sublattice, to fulfil high-entropy oxide (HEO) criteria, has been developed and investigated as oxygen carrier for chemical looping combustion processes. As far as we know, nobody has explored this class of material for chemical looping combustion. Material is prepared by direct mixing of five metal oxides (CuO, Mn2O3, Fe2O3, TiO2, MgO), followed by calcination at 1000, 1100 and 1200 °C for 6 h in air. XRD characterization provides strong evidence that the synthesized oxygen carriers possess the hallmark properties of HEO, and SEM-EDX analysis shows an overall homogeneous metal distribution. Materials have one main cubic phase with the empirical formula MnCuMgFeTiO7, dominating under all conditions. One of the key objectives of this study is achieved, reduce chemical stress during redox cycles. Oxygen transfer capability is investigated by thermogravimetric analysis and batch fluidized bed reactor experiments for different fuels and atmospheres. Mass-based oxygen transport capacities for lattice oxygen and oxygen uncoupling are around 5.5 wt% and 1.1 wt%, respectively. This work opens up a new dimension for the future preparation of oxygen carriers for chemical looping processes, since the vast compositional space of HEO provides opportunities to tune both chemical and physical characteristics.
|
|
4. |
- Mendiara, Teresa, et al.
(author)
-
Effect of the Presence of Siloxanes in Biogas Chemical Looping Combustion
- 2021
-
In: Energy & Fuels. - : American Chemical Society (ACS). - 1520-5029 .- 0887-0624. ; 35:18, s. 14984-14994
-
Journal article (peer-reviewed)abstract
- Siloxanes are a group of Si-based impurities, common in biogas. Although normally present in relatively small amounts, their presence could be highly problematic, as the generated Si could be a precursor to abrasion and wear in downstream components. In this work, the siloxane effect in biogas chemical looping combustion (CLC) was evaluated. CLC of biogas could be an efficient way of achieving CO2 negative emissions. Two oxygen carriers (CuO-based and Fe2O3-based residue) were used in the combustion of a simulated biogas stream in a batch fluidized bed reactor. Here one of the most common siloxane compounds (hexamethyldisiloxane, L2) was utilized together with methane, the most common combustible component in biogas. The siloxane decomposed in the batch reactor, forming gaseous compounds and Si-based particles. The gaseous compounds formed (mainly CO, H2, CH4, and C2) were able to react with the oxygen carrier, whereas the Si originating from the siloxane interacted with the oxygen carrier particles. Elemental analyses of samples obtained from the reactor bed after combustion experiments revealed that significant amounts of Si from siloxane could be found in the oxygen carrier. The X-ray photoelectron spectroscopy (XPS) analyses of the same samples showed that silica in the oxygen carrier was mainly found at the surface of the particles and in the form of SiO2 or silicates/aluminosilicates. The XPS results were in agreement with a theoretical thermodynamic analysis performed to determine the possible stable Si-based species that may be formed. Although the deposition/formation of silica compounds in the oxygen carrier may lead to the agglomeration of particles, such a phenomenon was not observed in the present work.
|
|