1. |
- Abel, I, et al.
(author)
-
Overview of the JET results with the ITER-like wall
- 2013
-
In: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10, s. 104002-
-
Journal article (peer-reviewed)abstract
- Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Z(eff) (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. The re-establishment of the baseline H-mode and hybrid scenarios compatible with the new wall has required an optimization of the control of metallic impurity sources and heat loads. Stable type-I ELMy H-mode regimes with H-98,H-y2 close to 1 and beta(N) similar to 1.6 have been achieved using gas injection. ELM frequency is a key factor for the control of the metallic impurity accumulation. Pedestal temperatures tend to be lower with the new wall, leading to reduced confinement, but nitrogen seeding restores high pedestal temperatures and confinement. Compared with the carbon wall, major disruptions with the new wall show a lower radiated power and a slower current quench. The higher heat loads on Be wall plasma-facing components due to lower radiation made the routine use of massive gas injection for disruption mitigation essential.
|
|
2. |
- Romanelli, F, et al.
(author)
-
Overview of the JET results
- 2011
-
In: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 51:9
-
Journal article (peer-reviewed)abstract
- Since the last IAEA Conference JET has been in operation for one year with a programmatic focus on the qualification of ITER operating scenarios, the consolidation of ITER design choices and preparation for plasma operation with the ITER-like wall presently being installed in JET. Good progress has been achieved, including stationary ELMy H-mode operation at 4.5 MA. The high confinement hybrid scenario has been extended to high triangularity, lower ρ*and to pulse lengths comparable to the resistive time. The steady-state scenario has also been extended to lower ρ*and ν*and optimized to simultaneously achieve, under stationary conditions, ITER-like values of all other relevant normalized parameters. A dedicated helium campaign has allowed key aspects of plasma control and H-mode operation for the ITER non-activated phase to be evaluated. Effective sawtooth control by fast ions has been demonstrated with3He minority ICRH, a scenario with negligible minority current drive. Edge localized mode (ELM) control studies using external n = 1 and n = 2 perturbation fields have found a resonance effect in ELM frequency for specific q95values. Complete ELM suppression has, however, not been observed, even with an edge Chirikov parameter larger than 1. Pellet ELM pacing has been demonstrated and the minimum pellet size needed to trigger an ELM has been estimated. For both natural and mitigated ELMs a broadening of the divertor ELM-wetted area with increasing ELM size has been found. In disruption studies with massive gas injection up to 50% of the thermal energy could be radiated before, and 20% during, the thermal quench. Halo currents could be reduced by 60% and, using argon/deuterium and neon/deuterium gas mixtures, runaway electron generation could be avoided. Most objectives of the ITER-like ICRH antenna have been demonstrated; matching with closely packed straps, ELM resilience, scattering matrix arc detection and operation at high power density (6.2 MW m-2) and antenna strap voltages (42 kV). Coupling measurements are in very good agreement with TOPICA modelling. © 2011 IAEA, Vienna.
|
|
3. |
- Beurskens, M N A, et al.
(author)
-
H-mode pedestal scaling in DIII-D, ASDEX Upgrade, and JET
- 2011
-
In: Physics of Plasmas. - : AIP Publishing. - 1070-664X .- 1089-7674. ; 18:5
-
Journal article (peer-reviewed)abstract
- Multidevice pedestal scaling experiments in the DIII-D, ASDEX Upgrade (AUG), and JET tokamaks are presented in order to test two plasma physics pedestal width models. The first model proposes a scaling of the pedestal width Delta/a proportional to rho*(1/2) to rho* based on the radial extent of the pedestal being set by the point where the linear turbulence growth rate exceeds the E x B velocity. In the multidevice experiment where rho* at the pedestal top was varied by a factor of four while other dimensionless parameters where kept fixed, it has been observed that the temperature pedestal width in real space coordinates scales with machine size, and that therefore the gyroradius scaling suggested by the model is not supported by the experiments. The density pedestal width is not invariant with rho* which after comparison with a simple neutral fuelling model may be attributed to variations in the neutral fuelling patterns. The second model, EPED1, is based on kinetic ballooning modes setting the limit of the radial extent of the pedestal region and leads to Delta(psi) proportional to beta p(1/2). All three devices show a scaling of the pedestal width in normalised poloidal flux as Delta(psi) proportional to beta p(1/2), as described by the kinetic ballooning model; however, on JET and AUG, this could not be distinguished from an interpretation where the pedestal is fixed in real space. Pedestal data from all three devices have been compared with the predictive pedestal model EPED1 and the model produces pedestal height values that match the experimental data well.
|
|
4. |
- Leyland, M. J., et al.
(author)
-
Pedestal study across a deuterium fuelling scan for high delta ELMy H-mode plasmas on JET with the carbon wall
- 2013
-
In: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 53:8, s. 083028-
-
Journal article (peer-reviewed)abstract
- We present the results from a new fuelling scan database consisting of 14 high triangularity (delta similar to 0.41), type I ELMy H-mode JET plasmas. As the fuelling level is increased from low, (Gamma(D) similar to 0.2 x 10(22) el s(-1), n(e),(ped)/n(GW) = 0.7), to high dosing (Gamma(D) similar to 2.6 x 10(22) el s(-1), n(e, ped)/n(GW) = 1.0) the variation in ELM behaviour is consistent with a transition from 'pure type I' to 'mixed type I/II' ELMs (Saibene et al 2002 Plasma Phys. Control. Fusion 44 1769). However, the pulses in this new database are better diagnosed in comparison to previous studies and most notable have pedestal measurements provided by the JET high resolution Thomson scattering (HRTS) system. We continue by presenting, for the first time, the role of pedestal structure, as quantified by a least squares mtanh fit to the HRTS profiles, on the performance across the fuelling scan. A key result is that the pedestal width narrows and peak pressure gradient increases during the ELM cycle for low fuelling plasmas, whereas at high fuelling the pedestal width and peak pressure gradient saturates towards the latter half of the ELM cycle. An ideal MHD stability analysis shows that both low and high fuelling plasmas move from stable to unstable approaching the ideal ballooning limit of the finite peeling-ballooning stability boundary. Comparison to EPED predictions show on average good agreement with experimental measurements for both pedestal height and width however when presented as a function of pedestal density, experiment and model show opposing trends. The measured pre-ELM pressure pedestal height increases by similar to 20% whereas EPED predicts a decrease of 25% from low to high fuelling. Similarly the measured pressure pedestal width widens by similar to 55%, in poloidal flux space, whereas EPED predicts a decrease of 20% from low to high fuelling. We give two possible explanations for the disagreement. First, it may be that EPED under predicts the critical density, which marks the transition from kink-peeling to ballooning-limited plasmas. Second, the stronger broadening of the experimental pedestal width than predicted by EPED is an indication that other transport related processes contribute to defining the pedestal width such as enhanced inter-ELM transport as observed at high fuelling, for mixed type I/II ELMy pulses.
|
|
5. |
- Nave, M. F. F., et al.
(author)
-
JET intrinsic rotation studies in plasmas with a high normalized beta and varying toroidal field ripple
- 2012
-
In: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 0741-3335 .- 1361-6587. ; 54:7, s. 074006-
-
Journal article (peer-reviewed)abstract
- Understanding the origin of rotation in ion cyclotron resonance frequency (ICRF) heated plasmas is important for predictions for burning plasmas sustained by alpha particles, being characterized by a large population of fast ions and no external momentum input. The angular velocity of the plasma column has been measured in JET H-mode plasmas with pure ICRF heating both for the standard low toroidal magnetic ripple configuration, of about similar to 0.08% and, for increased ripple values up to 1.5% (Nave et al 2010 Phys. Rev. Lett. 105 105005). These new JET rotation data were compared with the multi-machine scaling of Rice et al (2007 Nucl. Fusion 47 1618) for the Alfven-Mach number and with the scaling for the velocity change from L-mode into H-mode. The JET data do not fit well any of these scalings that were derived for plasmas that are co-rotating with respect to the plasma current. With the standard low ripple configuration, JET plasmas with large ICRF heating power and normalized beta, beta(N) approximate to 1.3, have a very small co-current rotation, with Alfven-Mach numbers significantly below those given by the rotation scaling of Rice et al (2007 Nucl. Fusion 47 1618). In some cases the plasmas are actually counter-rotating. No significant difference between the H-mode and L-mode rotation is observed. Typically the H-mode velocities near the edge are lower than those in L-modes. With ripple values larger than the standard JET value, between 1% and 1.5%, H-mode plasmas were obtained where both the edge and the core counter-rotated.
|
|
6. |
- Versloot, T W, et al.
(author)
-
Comparison between dominant NB and dominant IC heated ELMy H-mode discharges in JET
- 2011
-
In: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 51:10, s. 103033-
-
Journal article (peer-reviewed)abstract
- The experiment described in this paper is aimed at characterization of ELMy H-mode discharges with varying momentum input, rotation, power deposition profiles and ion to electron heating ratio obtained by varying the proportion between ion cyclotron (IC) and neutral beam (NB) heating. The motivation for the experiment was to verify if the basic confinement and transport properties of the baseline ITER H-mode are robust to these changes, and similar to those derived mostly from dominant NB heated H-modes. No significant difference in the density and temperature profiles or in the global confinement were found. Although ion temperature profiles were seen to be globally stiff, some variation of stiffness was obtained in the experiment by varying the deposition profiles, but not one that could significantly affect the profiles in terms of global confinement. This analysis shows the thermal plasma energy confinement enhancement factor to be independent of the heating mix, for the range of conditions explored. Moreover, the response of the global confinement to changes in density and power were also independent of heating mix, reflecting the changes in the pedestal, which is in agreement with globally stiff profiles. Consistently, the pedestal characteristics (pressure and width) and their dependences on global parameters such as density and power were the same during NB only or with predominant IC heating.
|
|