| 1. |
- Vernersson, Tore V, 1968, et al.
(author)
-
Wear of Railway brake block materials at elevated temperatures : pin-on-disc experiments
- 2012
-
In: Proceedings of Eurobrake 2012. - FISITA.
-
Conference paper (peer-reviewed)abstract
- An experimental study on a pin-on-disc rig is presented where the wear of some brake block materials at controlled elevated disc temperatures are reported. It is found for the three studied organic composite materials that the (specific) wear rate increases radically at a temperature of about 500 oC. For temperatures below 500 oC, the wear rate is found to increase with temperature. The cast iron material shows an increase of the wear rate up to 500 oC, after which a transition in the wear mechanism occurs and the wear rate is decreasing with increasing temperature. The studied sinter material shows a weak dependence of the wear rate with temperature.
|
|
| 2. |
- Mill, O., et al.
(author)
-
Analysis and development of hydro power research : synthesis within Swedish Hydro Power Centre
- 2010
-
Reports (other academic/artistic)abstract
- The market for hydropower re-investments in Sweden is approx 2.5 billion SEK/yr the coming decade. Large investments will also be carried out in Swedish tailing dams. This will result in challenging projects and need of experts. A crucial factor for a successful management of these challenges is the supply of engineers and researchers with hydro power and dam skills and knowledge. Swedish Hydro Power Centre (Svenskt vattenkraftcentrum, SVC) is a competence centre for university education and research environments within hydro power and mining dams. SVC comprises of two knowledge areas: Hydraulic Engineering and Hydro Turbines and Generators, respectively. SVC builds high-quality and long term sustainable knowledge at selected universities...
|
|
| 3. |
|
|
| 4. |
- Karlsson, Patrik, 1973-, et al.
(author)
-
Galling resistance and wear mechanisms for cold-work tool steels in lubricated sliding against high strength stainless steel sheets
- 2012
-
In: Wear. - Amsterdam : Elsevier. - 0043-1648 .- 1873-2577. ; 286-287, s. 92-97
-
Journal article (peer-reviewed)abstract
- Tool damage in sheet metal forming of stainless steel is of high concern for the forming industry. In the present work, ingot cast AISI D2 and advanced powder metallurgy tool steel (PM) cold-work tool steels were evaluated and ranked regarding wear mechanisms and galling resistance. Wear tests were performed using a slider-on-flat-surface (SOFS) tribometer in sliding against austenitic–ferritic (duplex) stainless steel sheets at different contact pressures in lubricated conditions. The best galling resistance was observed for the nitrogen alloyed PM tool steels. Abrasive scratching of the tool surfaces and transfer of sheet material due to adhesive wear were the main metal forming tool surface damage mechanisms. By increasing the hardness of one PM sheet metal forming tool grade, the galling resistance was enhanced.
|
|
| 5. |
- Karlsson, Patrik, 1973-, et al.
(author)
-
Galling resistance evaluation of tool steels by two different laboratory test methods for sheet metal forming
- 2012
-
In: Lubrication Science. - : John Wiley & Sons. - 0954-0075 .- 1557-6833. ; 24:6, s. 263-272
-
Journal article (peer-reviewed)abstract
- Adhesive accumulation of work material on the tool surface is today a major problem in many sheet metal-forming applications. Different laboratory test methods are used to investigate galling with respect to different tool materials, lubricants and process conditions. In the present study, the galling resistance of a modern nitrogen-alloyed powder metallurgy tool steel and an conventional ingot cast D2 type tool steel was evaluated under lubricated sliding against ferritic stainless steel sheets using a commercial pin-on-disc (POD) and an in-house made slider-on-flat-surface (SOFS) tribotester. The investigated tool steels ranked similarly in terms of galling resistanc in both test methods. However, sliding distances to galling were longer for the SOFS equipment due to continuous sliding on new lubricated sheet surface. Best performance was demonstrated by the powder metallurgy tool steel treated to 65 HRC. Differences in friction behaviour and galling initiation were analysed on the basis of the two different working conditions, i.e. open (SOFS) and closed (POD) tribosystems. Copyright © 2012 John Wiley & Sons, Ltd.
|
|
| 6. |
- Karlsson, Patrik, 1973-, et al.
(author)
-
Influence of tool steel hard phase orientation and shape on galling
- 2014
-
In: Advanced Materials Research. - : Trans Tech Publications. - 1022-6680 .- 1662-8985. ; 966-96, s. 249-258
-
Journal article (peer-reviewed)abstract
- Conventionally manufactured cold work tool steel is often used in sheet metal forming as die material. Due to the forging process, the as-cast network structure of carbides is broken into elongated particles. Depending on the tool cross-section, the orientation and shape of carbides in the active tool surface is different. In the present research, the influence of tool steel hard phase orientation and shape on galling was investigated. D2 type tool steel was cut in three different orientations and tested in lubricated sliding conditions against AISI 304 austenitic stainless steel. Tests were performed using a Slider-On-Flat-Surface and galling was detected by changes in friction and post-test microscopy. The lubricant was Castrol FST8 using 5 g/m2 sheet material. Results showed a strong correlation between sliding distance to galling and tool steel hard phase orientation and shape at low loads, whereas high load contact resulted in early galling in all cases. Material transfer was observed mainly to the tool steel matrix. The worst performance was observed for specimens cut so that the tool steel hard phase, M7C3 carbides in the D2 steel, were oriented along the sliding direction, which resulted in longer open tool matrix areas contacting the sheet material.
|
|
| 7. |
- Karlsson, Patrik, 1973-, et al.
(author)
-
Influence of tool steel microstructure on friction and initial material transfer
- 2014
-
In: Wear. - : Elsevier. - 0043-1648 .- 1873-2577. ; 319:1-2, s. 12-18
-
Journal article (peer-reviewed)abstract
- An investigation was conducted to study the influence of tool steel microstructure on initial material transfer and friction. Two different powder metallurgy tool steels and an ingot cast tool material were tested in dry sliding against 1.4301, 1.4162, Domex 355 MC and Domex 700 MC sheet materials. It was found that tool steel hard phase heights influence initial material transfer and friction. The coefficient of friction increased with decreasing tool steel hard phase heights at 50 N normal load and initial material transfer occurred around protruding hard phases. At higher load of 500 N the sheet material adhered to both the tool steel matrix and hard phases. Coefficient of friction decreased with increasing proof strength of the sheet material at 500 N normal load.
|
|
| 8. |
- Karlsson, Patrik, 1973-, et al.
(author)
-
Influence of work material proof stress and tool steel microstructure on galling initiation and critical contact pressure
- 2013
-
In: Tribology International. - Amsterdam : Elsevier. - 0301-679X .- 1879-2464. ; 60, s. 104-110
-
Journal article (peer-reviewed)abstract
- EN 1.4301 (austenitic), EN 1.4509 (ferritic), EN 1.4162 (duplex) and EN 1.4310 C1000 (metastable austenitic) stainless steels were tested in lubricated sliding against an ingot cast EN X153WCrMoV12 and powder metallurgy nitrogen alloyed Uddeholm Vancron 40 tool steels to reveal critical to galling contact pressure, Pcr. The calculated Pcr were higher for steels with higher strength. At P>Pcr, due to plastic flow of sheet material, the tool is damaged substantially and wear-induced matrix damage causes rapid galling initiation. At P
|
|
| 9. |
- Abbasi, Saeed, 1973-, et al.
(author)
-
Temperature and Thermoelastic Instability at Tread Braking Using Cast Iron Friction Material
- 2013
-
In: Wear. - : Elsevier BV. - 0043-1648 .- 1873-2577. ; 314:1–2, s. 171-180
-
Journal article (peer-reviewed)abstract
- Braking events in railway traffic often induce high frictional heating and thermoelastic instability (TEI) at the interfacing surfaces. In the present paper, two approaches are adopted to analyse the thermomechanical interaction in a pin-on-disc experimental study of railway braking materials. In a first part, the thermal problem is studied to find the heat partitioning between pin and disc motivated by the fact that wear mechanisms can be explained with a better understanding of the prevailing thermal conditions. The numerical model is calibrated using the experimental results. In a second part, the frictionally induced thermoelastic instabilities at the pin-disc contact are studied using a numerical method and comparing them with the phenomena observed in the experiments. The effects of temperature on material properties and on material wear are considered. It is found from the thermal analysis that the pin temperature and the heat flux to the pin increase with increasing disc temperatures up to a transition stage. This agrees with the behaviour found in the experiments. Furthermore, the thermoelastic analysis displays calculated pressure and the temperature distributions at the contact interface that are in agreement with the hot spot behaviour observed in the experiments.
|
|
| 10. |
- Caprioli, Sara, 1978
(author)
-
Thermal impact on rolling contact fatigue of railway wheels
- 2014
-
Doctoral thesis (other academic/artistic)abstract
- Rolling contact fatigue (RCF) is a very common and costly damage mechanism for rails and wheels. This thesis investigates the influence of combined thermal and mechanical loading on RCF of railway wheels on the basis of numerical predictions. The established computational framework includes heat flux analyses, (two- and three-dimensional) elastoplastic finite element simulations and subsequent RCF life analyses. The computational framework is employed to quantify the influence of various operational parameters and modelling presumptions such as applied heat and tangential stress characteristics, load application schemes, mesh densities etc. Examples of results include quantifications of how partial slip conditions result in higher plastic strain magnitudes in a thin layer at the wheel tread surface, and differences in material responses between accelerating and braking wheels.The numerical model was extended to incorporate surface initiated cracks. With the extended model it is shown that 1 mm deep cracks have a substantial influence on the state of stress and strain in the bulk material between surface cracks. Further, comparisons between radial (thermal) and inclined (RCF) surface cracks show that the deformation of significantly inclined cracks (30 degrees) is more severe than that of radial cracks. Further, acceleration is found to give larger crack face displacements. However braking tends to induce tensile residual stresses that open the crack mouth, thus allowing fluid penetration that can promote crack growth. Also thermal loading is found to cause a significant crack mouth opening that is decreased by subsequent rolling contact.In a final study numerical RCF predictions are compared to full-scale experimental studies carried out at the Railway Technical Research Institute in Japan. Thermal loading tuned towards measurements by thermocameras and thermocouples are introduced in a truncated loading scheme corresponding to the test configuration. Estimated crack initiation life is found to be in good agreement with test results. The investigation also shows the significant influence of the employed material model. In addition to thermomechanical fatigue analyses, the case of purely thermal fracture has been investigated. This study quantified how the risk of fracture and resulting crack sizes depend on braking conditions and initial surface cracks. The results of this thesis are believed to be of importance in defining and enforcing sustainable operational conditions and maintenance actions. Further, this thesis provides tools to establish root causes and pertinent mitigating actions when thermomechanical wheel cracking nevertheless occurs.
|
|
