| 1. |
- Buckland, Philip I., 1973-, et al.
(author)
-
The Strategic Environmental Archaeology Database : a resource for international, multiproxy and transdisciplinary studies of environmental and climatic change
- 2015
-
Conference paper (peer-reviewed)abstract
- Climate and environmental change are global challenges which require global data and infrastructure to investigate. These challenges also require a multi-proxy approach, integrating evidence from Quaternary science and archaeology with information from studies on modern ecology and physical processes among other disciplines. The Strategic Environmental Archaeology Database (SEAD http://www.sead.se) is a Swedish based international research e-infrastructure for storing, managing, analysing and disseminating palaeoenvironmental data from an almost unlimited number of analysis methods. The system currently makes available raw data from over 1500 sites (>5300 datasets) and the analysis of Quaternary fossil insects, plant macrofossils, pollen, geochemistry and sediment physical properties, dendrochronology and wood anatomy, ceramic geochemistry and bones, along with numerous dating methods. This capacity will be expanded in the near future to include isotopes, multi-spectral and archaeo-metalurgical data. SEAD also includes expandable climate and environment calibration datasets, a complete bibliography and extensive metadata and services for linking these data to other resources. All data is available as Open Access through http://qsead.sead.se and downloadable software. SEAD is maintained and managed at the Environmental Archaeology Lab and HUMlab at Umea University, Sweden. Development and data ingestion is progressing in cooperation with The Laboratory for Ceramic Research and the National Laboratory for Wood Anatomy and Dendrochronology at Lund University, Sweden, the Archaeological Research Laboratory, Stockholm University, the Geoarchaeological Laboratory, Swedish National Historical Museums Agency and several international partners and research projects. Current plans include expanding its capacity to serve as a data source for any system and integration with the Swedish National Heritage Board's information systems. SEAD is partnered with the Neotoma palaeoecology database (http://www.neotomadb.org) and a new initiative for building cyberinfrastructure for transdisciplinary research and visualization of the long-term human ecodynamics of the North Atlantic funded by the National Science Foundation (NSF).
|
|
| 2. |
- Åkerfeldt, Pia, et al.
(author)
-
Electron backscatter diffraction characterization of fatigue crack growth in laser metal wire deposited Ti-6Al-4V
- 2018
-
In: Materials Characterization. - : Elsevier BV. - 1044-5803 .- 1873-4189. ; 135, s. 245-256
-
Journal article (peer-reviewed)abstract
- By additive manufacturing (AM) there is a feasibility of producing near net shape components in basically one step from 3D CAD model to final product. The interest for AM is high and during the past decade a lot of research has been carried out in order to understand the influence from process parameters on the microstructure and furthermore on the mechanical properties. In the present study laser metal wire deposition of Ti-6Al-4V has been studied in detail with regard to its fatigue crack propagation characteristics. Two specimen orientations, parallel and perpendicular to the deposition direction, have been evaluated at room temperature and at 250 °C. No difference in the fatigue crack growth rate could be confirmed for the two specimen orientations. However, in the fractographic study it was observed that the tortuosity varied between certain regions on the fracture surface. The local crack path characteristic could be related to the alpha colony size and/or the crystallographic orientation. Moreover, large areas exhibiting similar crystallographic orientation were observed along the prior beta grain boundaries, which were attributed to the wide alpha colonies frequently observed along the prior beta grain boundaries. © 2017 Elsevier Inc.
|
|
| 3. |
|
|
| 4. |
- Åkerfeldt, Maria, 1982, et al.
(author)
-
Textile piezoelectric sensors – melt spun bi-component poly(vinylidene fluoride) fibres with conductive cores and poly(3,4-ethylene dioxythiophene)-poly(styrene sulfonate) coating as the outer electrode
- 2014
-
In: Fashion and Textiles. - : Springer Science and Business Media LLC. - 2198-0802. ; 1:1
-
Journal article (peer-reviewed)abstract
- The work presented here addresses the outer electroding of a fully textile piezoelectric strain sensor, consisting of bi-component fibre yarns of β-crystalline poly(vinylidene fluoride) (PVDF) sheath and conductive high density polyethylene (HDPE)/carbon black (CB) core as insertions in a woven textile, with conductive poly(3,4-ethylene dioxythiophene)-poly(styrene sulfonate) (PEDOT:PSS) coatings developed for textile applications. Two coatings, one with a polyurethane binder and one without, were compared for the application and evaluated as electrode material in piezoelectric testing, as well as tested for surface resistivity, tear strength, abrasion resistance and shear flexing. Both coatings served their function as the outer electrodes in the system and no difference in this regard was detected between them. Omission of the binder resulted in a surface resistivity one order of magnitude less, of 12.3 Ω/square, but the surface resistivity of these samples increased more upon abrasion than the samples coated with binder. The tear strength of the textile coated with binder decreased with one third compared to the uncoated substrate, whereas the tear strength of the coated textile without binder increased with the same amount. Surface resistivity measurements and scanning electron microscopy (SEM) images of the samples subjected to shear flexing showed that the coatings without the binder did not withstand this treatment, and that the samples with the binder managed this to a greater extent. In summary, both of the PEDOT:PSS coatings could be used as outer electrodes of the piezoelectric fibres, but inclusion of binder was found necessary for the durability of the coating.
|
|
| 5. |
- Chen, Zhe, et al.
(author)
-
Nano-scale characterization of white layer in broached Inconel 718
- 2017
-
In: Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. - Amsterdam : Elsevier BV. - 0921-5093 .- 1873-4936. ; 684, s. 373-384
-
Journal article (peer-reviewed)abstract
- The formation mechanism of white layers during broaching and their mechanical properties are not well investigated and understood to date. In the present study, multiple advanced characterization techniques with nano-scale resolution, including transmission electron microscopy (TEM), transmission Kikuchi diffraction (TKD), atom probe tomography (APT) as well as nano-indentation, have been used to systematically examine the microstructural evolution and corresponding mechanical properties of a surface white layer formed when broaching the nickel-based superalloy Inconel 718.TEM observations showed that the broached white layer consists of nano-sized grains, mostly in the range of 20–50 nm. The crystallographic texture detected by TKD further revealed that the refined microstructure is primarily caused by strong shear deformation. Co-located Al-rich and Nb-rich fine clusters have been identified by APT, which are most likely to be γ′ and γ′′ clusters in a form of co-precipitates, where the clusters showed elongated and aligned appearance associated with the severe shearing history. The microstructural characteristics and crystallography of the broached white layer suggest that it was essentially formed by adiabatic shear localization in which the dominant metallurgical process is rotational dynamic recrystallization based on mechanically-driven subgrain rotations. The grain refinement within the white layer led to an increase of the surface nano-hardness by 14% and a reduction in elastic modulus by nearly 10% compared to that of the bulk material. This is primarily due to the greatly increased volume fraction of grain boundaries, when the grain size was reduced down to the nanoscale.
|
|
| 6. |
- Lindberg, Siv M, et al.
(author)
-
A product semantic study of the influence of the sense of touch on the evaluation of wood-based materials
- 2013
-
In: Materials & design. - : Elsevier BV. - 0264-1275 .- 1873-4197 .- 0261-3069. ; 52, s. 300-307
-
Journal article (peer-reviewed)abstract
- Based on product semantics, this study investigated how the tactile attributes of wood and wood-based composites are perceived and interpreted semantically. The wood-based samples included ash, birch, elm, oak, pine, OSB (oriented strand board), two wood pulp-reinforced polylactide composites, Comp A and B and one wood-fiber reinforced polypropene composite, Comp C. The subjects rated the samples by the descriptive words natural, exclusive, eco-. friendly, rough, inexpensive, reliable, warm, modern, snug and solid. The most significant differences between the samples were found for roughness and for the descriptors, reliable, natural and solid. A principal component analysis yielded three attributes based on the tactile perceptions: reliable, old-. fashioned and smooth. The solid wood pieces were perceived as natural and oak was perceived as being exclusive. The composite materials presented a greater variation in terms of perceived attributes than the wood specimens.
|
|
| 7. |
- Sefer, Birhan, 1983-, et al.
(author)
-
Chemical Milling of Cast Ti-6Al-4V and Ti-6Al-2Sn-4Zr-2Mo Alloys in Hydrofluoric-Nitric Acid Solutions
- 2017
-
In: Corrosion. - : Association for Materials Protection and Performance (AMPP). - 0010-9312 .- 1938-159X. ; 73:4, s. 394-407
-
Journal article (peer-reviewed)abstract
- The behavior of cast Ti-6Al-4V and Ti-6Al-2Sn-4Zr-2Mo during chemical milling in hydrofluoric-nitric (HF-HNO3) acid solutions with 1:3 and 1:11 molar ratios was investigated using electrochemical and atomic force microscopy (AFM) techniques. Faster corrosion rate in 1:3 solutions was measured for Ti-6Al-4V than for Ti-6Al-2Sn-4Zr-2Mo, whereas in 1:11 solution Ti-6Al-2Sn-4Zr-2Mo exhibited higher corrosion rate. Scanning Kelvin probe force microscopy measurements revealed difference in the Volta potential between the α-laths and the β-layers in the Widmansttäten microstructure indicating operation of microgalvanic cells between the microconstituents when in contact with HF-HNO3 solution. The AFM topography measurements demonstrated faster corrosion of the α-laths compared to the β-layers, in both alloys. In 1:3 solutions, higher α/β height difference was measured in Ti-6Al-4V, whereas in 1:11 solution, the difference was higher in Ti-6Al-2Sn-4Zr-2Mo. The results revealed that the chemical milling behavior of the two investigated alloys is controlled by the microscopic corrosion behavior of the individual microconstituents.
|
|
| 8. |
|
|
| 9. |
- Grolig, Jan Gustav, 1986
(author)
-
Coated Ferritic Stainless Steels as Interconnects in Solid Oxide Fuel Cells - Material Development and Electrical Properties
- 2015
-
Doctoral thesis (other academic/artistic)abstract
- Solid oxide fuel cells (SOFCs) are attracting increasing interest as devices with potentialuses in decentralized and clean electricity and heat production. Several challengeswith respect to materials have to be overcome to achieve efficiencies and life-spansthat are sufficient for long-term applications.An important element of an SOFC stack is the interconnect component, which connectstwo adjacent fuel cell elements. Interconnects, which are commonly composedof ferritic stainless steels, have to be corrosion-resistant, mechanically stable and costoptimized.This work aimed to investigate economic solutions for interconnect materials and tounderstand the underlying mechanisms of degradation and electrical conduction ofthese materials. Mainly two substrates, a commercially available steel (AISI 441) anda ferritic stainless steel that was optimized for an SOFC application (Sandvik SanergyHT) were combined with different barrier coatings and exposed to a cathode-sideatmosphere. A method was developed that allows for the electrical characterizationof promising material systems and model alloys, thereby facilitating a fundamentalunderstanding of the dominant electrical conduction processes linked to the oxidescales that grow on interconnects. The AISI 441 steel coated with reactive elementsand cobalt showed good corrosion and chromium evaporation profiles, while AISI 441coated with cerium and cobalt also had promising electrical properties. The SanergyHT steel was examined with coatings of copper and iron and copper and manganese,respectively. The corrosion and chromium evaporation profiles of Sanergy HT wereimproved by coating with copper and iron. The copper and iron-coated Sanergy HTshowed lower area specific resistance values than cobalt-coated Sanergy HT. Chromia,which is the main constituent of oxide scales, was synthesized using differentmethods. The electrical properties of chromia were found to be sensitive to not onlyimpurities, but also heat treatment. Finally the electrical properties of cobalt- andcobalt cerium-coated Sanergy HT steels were investigated. It was revealed that theaddition of cerium improved the conductivity of the interconnect by both slowingdown chromia growth and preventing the outward diffusion of iron into the spinel.
|
|
| 10. |
- Neikter, Magnus, et al.
(author)
-
Microstructure and Defects in Additive Manufactured Titanium : a Comparison Between Microtomography and Optical Microscopy
- 2017
-
Conference paper (other academic/artistic)abstract
- The aim of this work has been to compare two different analysing methods; x-ray microtomography and light optical microscopy, when it comes to defects and microstructure of additively manufactured Ti-6Al-4V. The results show that both techniques have their pros and cons:microtomography is the preferred choice for defect detection by analysing the full 3D sample volume, while light optical microscopy is better for analysing finer details in 2D.
|
|
