1. |
- Baveja, P. P., et al.
(author)
-
Impact of photon lifetime on thermal rollover in 850-nm high-speed VCSELs
- 2012
-
In: Proceedings of SPIE - The International Society for Optical Engineering. - : SPIE. - 0277-786X .- 1996-756X. - 9780819489197 ; 8276
-
Conference paper (peer-reviewed)abstract
- We present an empirical thermal model for VCSELs based on extraction of temperature dependence of macroscopic VCSEL parameters from CW measurements. We apply our model to two, oxide-confined, 850-nm VCSELs, fabricated with a 9-mu m inner-aperture diameter and optimized for high-speed operation. We demonstrate that for both these devices, the power dissipation due to linear heat sources dominates the total self-heating. We further show that reducing photon lifetime down to 2 ps drastically reduces absorption heating and improves device static performance by delaying the onset of thermal rollover. The new thermal model can identify the mechanisms limiting the thermal performance and help in formulating the design strategies to ameliorate them.
|
|
2. |
- Davani, Hooman A., et al.
(author)
-
Polarization investigation of a tunable high-speed short-wavelength bulk-micromachined MEMS-VCSEL
- 2012
-
In: Proceedings of SPIE - The International Society for Optical Engineering. - : SPIE. - 0277-786X .- 1996-756X. - 9780819489197 ; 8276, s. Art. no. 82760T-
-
Conference paper (peer-reviewed)abstract
- We report the investigation of the state of polarization (SOP) of a tunable vertical-cavity surface-emitting laser (VCSEL) operating near 850 nm with a mode-hop free single-mode tuning range of about 12 nm and an amplitude modulation bandwidth of about 5 GHz. In addition, the effect of a sub-wavelength grating on the device and its influence on the polarization stability and polarization switching has been investigated. The VCSEL with an integrated sub-wavelength grating shows a stable SOP with a polarization mode suppression ratio (PMSR) more than 35 dB during the tuning.
|
|
3. |
- Haglund, Erik, 1985, et al.
(author)
-
Reducing the spectral width of high speed oxide confined VCSELs using an integrated mode filter
- 2012
-
In: Proceedings of SPIE - The International Society for Optical Engineering. - : SPIE. - 0277-786X .- 1996-756X. - 9780819489197 ; 8276, s. Article Number: 82760L-
-
Conference paper (peer-reviewed)abstract
- We have reduced the spectral width of high speed oxide confined 850 nm VCSELs using a shallow surface relief for suppression of higher order transverse modes. The surface relief acts as a mode filter by introducing a spatially varying and therefore mode selective loss. The VCSEL employs multiple oxide layers for reduced capacitance which leads to a strong index guiding and a large spectral width in the absence of a mode filter. With an appropriate choice of surface relief parameters, the RMS spectral width for a 5 jam oxide aperture VCSEL is reduced from 0.6 to 0.3 nm. The small signal modulation bandwidth is 19 GHz. Due to reduced effects of chromatic and modal fiber dispersion, the maximum error-free (bit-error-rate
|
|
4. |
- Kögel, Benjamin, 1979, et al.
(author)
-
Integrated MEMS-tunable VCSELs for reconfigurable optical interconnects
- 2012
-
In: Proceedings of SPIE - The International Society for Optical Engineering. - : SPIE. - 0277-786X .- 1996-756X. - 9780819489197 ; 8276, s. Article Number: 82760Q-
-
Conference paper (peer-reviewed)abstract
- A simple and low-cost technology for tunable vertical-cavity surface-emitting lasers (VCSELs) with curved movable micromirror is presented. The micro-electro-mechanical system (MEMS) is integrated with the active optical component (so-called half-VCSEL) by means of surface-micromachining, using a reflown photoresist droplet as sacrificial layer. The technology is demonstrated for electrically pumped, short-wavelength (850nm) tunable VCSEts. Fabricated devices with 10 mu m oxide aperture are singlemode with sidemode suppression >35 dB, tunable over 24 mit with output power up to 0.5 mW, and have a beam divergence angle
|
|
5. |
- Larsson, Anders, 1957, et al.
(author)
-
High-speed tunable and fixed-wavelength VCSELs for short-reach optical links and interconnects
- 2012
-
In: Proceedings of SPIE - The International Society for Optical Engineering. - : SPIE. - 0277-786X .- 1996-756X. - 9780819489197 ; 8276, s. Article Number: 82760H-
-
Conference paper (peer-reviewed)abstract
- This paper presents a review of recent work on high speed tunable and fixed wavelength vertical cavity surface emitting lasers (VCSELs) at Chalmers University of Technology. All VCSELs are GaAs-based, employ an oxide aperture for current and/or optical confinement, and emit around 850 nm. With proper active region and cavity designs, and techniques for reducing capacitance and thermal impedance, our fixed wavelength VCSELs have reached a modulation bandwidth of 23 GHz, which has enabled error-free 40 Gbps back-to-back transmission and 35 Gbps transmission over 100 m of multimode fiber. A MEMS-technology for wafer scale integration of tunable high speed VCSELs has also been developed. A tuning range of 24 nm and a modulation bandwidth of 6 GHz have been achieved, enabling error-free back-to-back transmission at 5 Gbps.
|
|
6. |
- Alexander, Naomi E., et al.
(author)
-
IMAGINE project : A low cost, high performance, monolithic passive mm-wave imager front-end
- 2012
-
In: Proceedings of SPIE - The International Society for Optical Engineering. - : SPIE. - 0277-786X .- 1996-756X. - 9780819492852
-
Conference paper (peer-reviewed)abstract
- The FP7 Research for SME project IMAGINE - a low cost, high performance monolithic passive mm-wave imager front-end is described in this paper. The main innovation areas for the project are: i) the development of a 94 GHz radiometer chipset and matching circuits suitable for monolithic integration. The chipset consists of a W-band low noise amplifier, fabricated using the commercially available OMMIC D007IH GaAs mHEMT process, and a zero bias resonant interband tunneling diode, fabricated using a patented epi-layer structure that is lattice matched to the same D007IH process; ii) the development of a 94 GHz antenna adapted for low cost manufacturing methods with performance suitable for real-time imaging; iii) the development of a low cost liquid crystal polymer PCB build-up technology with performance suitable for the integration and assembly of a 94 GHz radiometer module; iv) the assembly of technology demonstrator modules. The results achieved in these areas are presented.
|
|
7. |
- Andreani, P., et al.
(author)
-
The European ALMA Regional Centre: a model of user support
- 2014
-
In: Proceedings of SPIE - The International Society for Optical Engineering. - : SPIE. - 0277-786X .- 1996-756X. - 9780819496171 ; 9149, s. Art. no. 91490Y-
-
Conference paper (peer-reviewed)abstract
- The ALMA Regional Centres (ARCs) form the interface between the ALMA observatory and the user community from the proposal preparation stage to the delivery of data and their subsequent analysis. The ARCs provide critical services to both the ALMA operations in Chile and to the user community. These services were split by the ALMA project into core and additional services. The core services are financed by the ALMA operations budget and are critical to the successful operation of ALMA. They are contractual obligations and must be delivered to the ALMA project. The additional services are not funded by the ALMA project and are not contractual obligations, but are critical to achieve ALMA full scientific potential. A distributed network of ARC nodes (with ESO being the central ARC) has been set up throughout Europe at the following seven locations: Bologna, Bonn-Cologne, Grenoble, Leiden, Manchester, Ondrejov, Onsala. These ARC nodes are working together with the central node at ESO and provide both core and additional services to the ALMA user community. This paper presents the European ARC, and how it operates in Europe to support the ALMA community. This model, although complex in nature, is turning into a very successful one, providing a service to the scientific community that has been so far highly appreciated. The ARC could become a reference support model in an age where very large collaborations are required to build large facilities, and support is needed for geographically and culturally diverse communities.
|
|
8. |
- Antosiewicz, Tomasz, 1981, et al.
(author)
-
Bi-metal coated aperture SNOM probes
- 2011
-
In: Proceedings of SPIE - The International Society for Optical Engineering. - : SPIE. - 0277-786X .- 1996-756X. - 9780819486608 ; 8070
-
Conference paper (peer-reviewed)abstract
- Aperture probes of scanning near-field optical microscopes (SNOM) offer resolution which is limited by a sum of the aperture diameter at the tip of a tapered waveguide probe and twice the skin depth in metal used for coating. An increase of resolution requires a decrease of the aperture diameter. However, due to low energy throughput of such probes aperture diameters usually are larger than 50 nm. A groove structure at fiber core-metal coating interface for photon-to-plasmon conversion enhances the energy throughput 5-fold for Al coated probes and 30-fold for Au coated probes due to lower losses in the metal. However, gold coated probes have lower resolution, first due to light coupling from the core to plasmons at the outside of the metal coating, and second due to the skin depth being larger than for Al. Here we report on the impact of a metal bilayer of constant thickness for coating aperture SNOM probes. The purpose of the bilayer of two metals of which the outer one is aluminum and the inner is a noble metal is to assure low losses, hence larger transmission. Using body-of-revolution finite-difference time-domain simulations we analyze properties of probes without corrugations to measure the impact of using a metal bilayer and choose an optimum bi-metal configuration. Additionally we investigate how this type of metalization works in the case of grooved probes.
|
|
9. |
- Antosiewicz, Tomasz, 1981, et al.
(author)
-
Magnetic probe for material characterization at optical frequencies
- 2011
-
In: Proceedings of SPIE - The International Society for Optical Engineering. - : SPIE. - 0277-786X .- 1996-756X. - 9780819486608 ; 8070
-
Conference paper (peer-reviewed)abstract
- Rapid development of novel, functional metamaterials made of purely dielectric, plasmonic, or composite structures which exhibit tunable optical frequency magnetic responses creates a need for new measurement techniques. We propose a method of actively measuring magnetic responses, i.e. magnetic dispersion, of such metamaterials within a wide range of optical frequencies with a single probe by exciting individual elementary cells within a larger matrix. The probe is made of a tapered optical fiber with a radially corrugated metal coating. It concentrates azimuthally polarized light in the near-field below the apex into a subwavelength size focus of the longitudinal magnetic field component. An incident azimuthally polarized beam propagates in the core until it reaches the metal stripes of constant angular width running parallel to the axis. For a broad frequency range light-to-plasmon coupling is assured as the lattice constant changes with the radius due to constant angular width. Bound plasmonic modes in slits between the metal stripes propagate toward the apex where circular currents in stripes and displacement currents in slits generate a strong longitudinal magnetic field. The energy density of the longitudinal magnetic component in the vicinity of the axis is much stronger than that of all the other components combined, what allows for pure magnetic excitation of magnetic resonances rather than by the electric field. The scattered signal is then measured in the far-field and analyzed.
|
|
10. |
- Antosiewicz, Tomasz, 1981, et al.
(author)
-
On the optical properties of plasmonic glasses
- 2014
-
In: Proceedings of SPIE - The International Society for Optical Engineering. - : SPIE. - 0277-786X .- 1996-756X. - 9781628415568 ; 9441, s. Art. no. 94411G-
-
Conference paper (peer-reviewed)abstract
- We report on the optical properties of plasmonic glasses which are metal-dielectric composites composed of metallic inclusions in a host dielectric medium. The investigated structures are of quasi-random nature, described by the pair correlation function, featuring a minimum center-to-center distance between metallic inclusions and long range randomness. Plasmonic glasses exhibiting short-range order only may be fabricated using bottom-up, self-assembly methods and have been utilized in a number of applications such as plasmonic sensing or plasmon-enhanced solar harvesting, and may be also employed for certain non-linear applications. It is therefore important to quantify their properties. Using theoretical methods we investigate optical of 1D, 2D, and 3D structures composed of amorphous distributions of metallic spheres. It is shown, that the response of the constituent element, i.e. The single sphere localized surface plasmon resonance, is modified by the scattered fields of the other spheres in such a way that its peak position, peak amplitude, and full-width at half-maximum exhibit damped oscillations. The oscillation amplitude is set by the particle density and for the peak position may vary by up to 0.3 eV in the optical regime. Using a modified coupled dipole approach we calculate the effective (average) polarizability of plasmonic glasses and discuss their spectra as a function of the dimensionality, angle of incidence and polarization, and the minimum center-to-center distance. The analytical model is complemented and validated by T-Matrix calculations of the optical cross-sections of amorphous arrays of metallic spheres obtained using a modification of the Random Sequential Adsorption algorithm for lines, surfaces, and volumes.
|
|