| 1. |
- Da Silva, Lucilene Moraes, et al.
(author)
-
Numerical investigation of film and impingement cooling schemes for gas turbine application
- 2018
-
In: Proceedings of the ASME Turbo Expo. ; 5A-2018
-
Conference paper (peer-reviewed)abstract
- In modern gas turbine engines, many sophisticated cooling schemes are used to maintain the turbine blade temperature in acceptable levels. These schemes, such as convective cooling, film cooling, impingement cooling and the use of pin fins, can be combined to increase the cooling effectiveness. Jet impingement cooling, pin fins and convective cooling are internal cooling techniques, in which the cooling is achieved based on coolant flow through internal blade channels decreasing the blade metal temperature. Film cooling is an external cooling technique, in which the cold fluid (air) is injected into the hot gas flow through discrete holes providing a coolant film at blade surface, protecting the blade metal. In this way, the present work refers to the numerical investigation of internal and external cooling strategies applied in gas turbines. The methodology developed to analyze such strategies is based on the flat-plate approach with laboratory length scales and Computational Fluid Dynamics (CFD) techniques, being the flow, in the study domain, considered viscous, turbulent and compressible. A commercial CFD program is used to solve the general equations of fluid mechanics with Reynolds Average Navier-Stokes (RANS) technique for steady state regime and Shear Stress Transport (SST) turbulence model to determine the flow eddy viscosity. The combined effects of internal and external cooling is studied through a highly sophisticated scheme, called louver, which combines the effects of impingement and film cooling. Pin fins and ribs turbulator geometries applied in the channel between the impingement and the film cooling have the purpose of evaluating the impact of these geometries on the film cooling effectiveness over the flat surface in comparison to the louver scheme without turbulator. This study concluded that, pin fins proved to be the most promise solution because they increased in 7% the film cooling effectiveness. Ribs also have a good potential to increase the effectiveness, because an increase of 4% in film cooling effectiveness was observed. In addition, the effects of the turbulator are dependent on their location, since the turbulator positioned near the film cooling hole exit showed improvements in the film cooling effectiveness in relation to the turbulator near of the impingement cooling jet.
|
|
| 2. |
- De Campos, Gustavo Bonolo, et al.
(author)
-
Propulsive efficiency of boundary layer ingestion propellers
- 2018
-
In: 31st Congress of the International Council of the Aeronautical Sciences, ICAS 2018.
-
Conference paper (peer-reviewed)abstract
- The pursuit of lower fuel consumption for aircraft is promoting a departure from contemporary arrangements. One example is the development of more synergetic airframe and propulsion system designs, which are expected to increase significantly aircraft efficiency mainly by means of boundary layer ingestion. By integrating propulsion and airframe, both systems will significantly impact each other. This mutual interference requires the development of novel performance evaluation methods that consider such effects. This manuscript introduces a propulsive efficiency equation for boundary layer ingestion propellers based on the power balance method. Two formulations are presented for numerical and analytical evaluations. The equation is bounded between 0 and 1 and allows a meaningful evaluation of shaft to propulsive powers conversion, which results in an accurate determination of thrust and drag. This manuscript is the first advance of a project that will develop an optimizing tool for boundary layer ingestion propellers based on computational fluid dynamic simulations. The results will be presented in subsequent manuscripts.
|
|
| 3. |
- Tavares Silva, Vinícius, 1991, et al.
(author)
-
A Propeller Model for Steady-State and Transient Performance Prediction of Turboprop and Counter-Rotating Open Rotor Engines
- 2018
-
In: Journal of Engineering for Gas Turbines and Power. - : ASME International. - 1528-8919 .- 0742-4795. ; 140:7, s. 1-13
-
Journal article (peer-reviewed)abstract
- This paper describes a methodology used for propeller performance estimation, which was implemented in an in-house modular program for gas turbine performance prediction. A model based on subsonic generic propeller maps and corrected for compressibility effects, under high subsonic speeds, was proposed and implemented. Considering this methodology, it is possible to simulate conventional turboprop architectures and counter-rotating open rotor (CROR) engines in both steady-state and transient operating conditions. Two simulation scenarios are available: variable pitch angle propeller with constant speed; or variable speed propeller with constant pitch angle. The simulations results were compared with test bench data and two gas turbine performance commercial software packages were used to fulfill the model validation for conventional turboprop configurations. Furthermore, a direct drive CROR engine was simulated using a variable inlet guide vanes (VIGV) control strategy during transient operation. The model has shown to be able to provide several information about propeller-based engine performance using few input data, and a comprehensive understanding on steady-state and transient performance behavior was achieved in the obtained results.
|
|
| 4. |
- Tavares Silva, Vinícius, 1991, et al.
(author)
-
Influence of Variable Geometry Compressor on Transient Performance of Counter-Rotating Open Rotor Engines
- 2018
-
In: Journal of Engineering for Gas Turbines and Power. - : ASME International. - 1528-8919 .- 0742-4795. ; 140:12
-
Journal article (peer-reviewed)abstract
- This work describes a methodology used for counter-rotating (CR) propellers performance estimation. The method is implemented in an in-house program for gas turbine performance prediction, making possible the simulation of the counter-rotating open rotor (CROR) architecture. The methodology is used together with a variable geometry compressor control strategy to avoid surge conditions. Two cases are simulated under transient operation for both fixed and variable geometry compressor. The influence of the variable geometry control on the transient performance of CROR engines is evaluated and a comprehensive understanding on the transient behavior of this type of engine could be obtained. It is shown that the use of the variable geometry compressor control does not significantly affect the overall engine performance, while avoiding the surge conditions, thus ensuring the engine operation safety.
|
|
